MT
2000
Series
Quick Start Guide
http://www.zebra.com/mt2000
POST IN WORK AREAPOST IN WORK AREA
Refer to User Guide for detailed information
8
9
Insert Scanner in Cradle
Desk Cradle
1
2
3
4
5
10
11
12
13
14
15
1 Left soft & ALT key
2 Tab & * key
6
7
3 Keypad
4 Orange key
5 Blue key
6 Battery
7 Tether Plate
8 LED Indicator
9 Scan Window
10 4-way Navigation key
1 1 Right soft & CTRL key
12 Cold boot trigger
13 LED Indicator (MT2090 Only)
14 Enter key
15 Scan Trigger
Wall Cradle
Forklift Cradle
BATTERY INSERTION
1 2
CONNECTIONS
Cradle Cable Connections
RS-232
BATTERY REMOVAL
1
2
HOST INTERFACES
Keyboard Wedge
3
Host
Power
Scanner Cable Connection
(USB & RS-232 only)
NOTE: Cables may vary depending on configuration. When using an external power supply, insert the
power cable into the cradle first, then insert the host cable. Connect the power cable to an AC outlet last.
USB
OR
IBM 46XX
OR
TROUBLESHOOTING
Refer to the MT2000 Series User Guide Troubleshooting section for further information.
Scanner not working
No power to scanner
Check battery
Scanner decoding bar code, but data not transmitting to host
Scanner not paired to host-connected cradle
Pair the scanner to the cradle (using the
PAIR bar code on the cradle)
NOTE: If data is still not transmitting to host, it may be necessary to recycle power on the cradle.
NOTE: Under certain circumstances, a fully discharged battery can take up to 30
minutes to charge before the scanner is operational. Refer to the User Guide for
detailed information.
Cradle not programmed for correct host interface
Check scanner host parameters or
edit options
Interface cable is loose
Check for loose cable
connections
Scanner not decoding bar code
Scanner not programmed
for bar code type
Ensure scanner is programmed
to read type of bar code being
scanned
Bar code unreadable
Ensure bar code is not defaced;
try scanning test bar code of same
bar code type
Scanned data incorrectly displayed on host
Paired cradle host communication parameters do not match the host’s parameters
Check cradle host parameters or edit options
Scanning application is not running
From the Home screen display on the
scanner, select Scan Item to run the
scanning application
RS-232 Host Types
STANDARD RS-232
ICL RS-232
MT2000 SERIES PROGRAMMING BAR CODES
Host Types Host Mode
Keyboard Wedge Host Types
CABLE PRIORITY
IBM PC/AT and IBM PC COMPATIBLE
Radio Communications Host Types
WIRELESS ONLY
Miscellaneous
CABLE ONLY
NIXDORF RS-232 MODE B
NIXDORF RS-232 MODE A
FUJITSU RS-232
CRADLE HOST
BLUETOOTH KEYBOARD EMULATION (HID SLAVE)
SERIAL PORT PROFILE (SLAVE)
Restore Defaults
Note: Paired scanners disconnect from the cradle
when Restore Defaults is scanned.
RESTORE DEFAULTS
Set Factory Defaults
Note: The Set Factory Defaults parameter only
changes the scanner’s programmable parameters to
the factory defaults.
SET FACTORY DEFAULTS
USB Host Types
HID KEYBOARD EMULATION
ACTIVESYNC HOST
OPOS/JPOS
IBM HAND-HELD USB
IBM 46XX Host Types
PORT 5B
SERIAL PORT PROFILE (MASTER)
PORT 9B
Scan to Add an Enter Key
(Carriage Return/Line Feed)
SCAN OPTIONS
<DATA><SUFFIX>
ENTER
Unpairing/Disconnection
UNPAIR/DISCONNECT
注
MT
2000
Series
Quick Start Guide
DESK-TO-WALL MOUNT CRADLE CONVERSION
(MT2090 only)
POST IN WORK AREAPOST IN WORK AREA
NOTE: When mounting a cradle on a wall, ensure the Wall Mount Conversion Dial on the back of the cradle is in the correct position before mounting. Refer to the User Guide for detailed information about single slot, four slot and forklift cradles.
SCANNER INDICATIONS
Scanner Beeper Indications
Standard Use
Low-medium-high beeps
Power up
Short low-high beeps
Scanner has paired with
the cradle
Normal beep
Bar code decoded [if
decode beeper enabled]
Short high-low beeps
Scanner has unpaired
with the cradle
4 long low beeps
Transmission error
detected; data is ignored
Long low-high beeps or
Long low-high-low-high beeps
Unsuccessful pairing attempt
Parameter Menu Scanning
High-low-high-low beeps
Successful program exit with change
in the parameter setting
Long low-high beeps
Input error, incorrect programming
sequence, or Cancel bar code scanned
Scanner Display Indications
Battery Strength Battery Charging/AC Power Wireless Signal Strength
Low battery; recharge Low battery
=
NOTE: If this icon displays in red, the scanner
battery is critically low and must be recharged
Battery 25% full
=
Battery 50% full
=
Battery 75% full
=
Battery full
=
=
Battery 25% full
=
Battery 50% full
=
Battery 75% full
=
Battery full
=
Scanner LED Indications
Standard Use
O
No power applied to scanner (battery
discharged or removed); scanner
is in low power and ready to scan;
or, battery is fully charged and scanner
is ready to scan
Charging Use
Green Flash
Scanner charging
(when cradle is
powered from external
power supply)
Battery Problem
Battery fault
=
?
Battery fault/AC power
=
?
Connection Icons
R
U
applied
Bluetooth active
=
(STB2078 only)
RS-232 cable attached
=
USB cable attached
=
Green
Bar code successfully
decoded
Red
Data transmission
error or scanner malfunction
No signal or
=
not associated
Very low signal
=
Low signal
=
Medium signal
=
=
Good signal
Excellent signal
=
Waste Electrical and Electronic Equipment (WEEE)
English: For EU Customers: All products at the end of their life must be returned
to Zebra for recycling. For information on how to return product, please go to:
http://www.zebra.com/weee.
Bulgarish: За клиенти от ЕС: След края на полезния им живот всички
продукти трябва да се връщат на Zebra за рециклиране. За информация
относно връщането на продукти, моля отидете на адрес:
http://www.zebra.com/weee.
Čeština: Pro zákazníky z EU: Všechny produkty je nutné po skonèení jejich
životnosti vrátit spoleènosti Zebra k recyklaci. Informace o zpùsobu vrácení
produktu najdete na webové stránce: http://www.zebra.com/weee.
Dansk: Til kunder i EU: Alle produkter skal returneres til Zebra til recirkulering,
når de er udtjent. Læs oplysningerne om returnering af produkter på:
http://www.zebra.com/weee.
Deutsch: Für Kunden innerhalb der EU: Alle Produkte müssen am Ende ihrer
Lebensdauer zum Recycling an Zebra zurückgesandt werden. Informationen zur
Rücksendung von Produkten finden Sie unter http://www.zebra.com/weee.
Ελληνικά: Για πελάτες στην Ε.Ε.: Όλα τα προϊόντα, στο τέλος της διάρκειας
ζωής τους, πρέπει να επιστρέφονται στην Zebra για ανακύκλωση. Για
περισσότερες πληροφορίες σχετικά με την επιστροφή ενός προϊόντος,
επισκεφθείτε τη διεύθυνση http://www.zebra.com/weee στο Διαδίκτυο.
Eesti: EL klientidele: kõik tooted tuleb nende eluea lõppedes tagastada
taaskasutamise eesmärgil Zebra'ile. Lisainformatsiooni saamiseks toote
tagastamise kohta külastage palun aadressi: http://www.zebra.com/weee.
Español: Para clientes en la Unión Europea: todos los productos deberán
entregarse a Zebra al final de su ciclo de vida para que sean reciclados. Si desea
más información sobre cómo devolver un producto, visite:
http://www.zebra.com/weee.
Français : Clients de l'Union Européenne : Tous les produits en fin de cycle de
vie doivent être retournés à Zebra pour recyclage. Pour de plus amples
informations sur le retour de produits, consultez : http://www.zebra.com/weee.
Hrvatski: Za kupce u Europskoj uniji: Svi se proizvodi po isteku vijeka trajanja
moraju vratiti tvrtki Zebra na recikliranje. Informacije o načinu vraćanja proizvoda
potražite na web-stranici: www.zebra.com/weee.
Italiano: per i clienti dell'UE: tutti i prodotti che sono giunti al termine del
rispettivo ciclo di vita devono essere restituiti a Zebra al fine di consentirne il
riciclaggio. Per informazioni sulle modalità di restituzione, visitare il seguente sito
Web: http://www.zebra.com/weee.
Latviešu: ES klientiem: visi produkti pēc to kalpošanas mūža beigām ir
jānogādā atpakaļ Zebra otrreizējai pārstrādei. Lai iegūtu informāciju par produktu
nogādāšanu Zebra, lūdzu, skatiet: http://www.zebra.com/weee.
Lietuvių: ES vartotojams: visi gaminiai, pasibaigus jų eksploatacijos laikui, turi
būti grąžinti utilizuoti į kompaniją „Zebra“. Daugiau informacijos, kaip grąžinti
gaminį, rasite: http://www.zebra.com/weee.
Magyar: Az EU-ban vásárlóknak: Minden tönkrement terméket a Zebra
vállalathoz kell eljuttatni újrahasznosítás céljából. A termék visszajuttatásának
módjával kapcsolatos tudnivalókért látogasson el a http://www.zebra.com/weee
weboldalra.
Malti: Għal klijenti fl-UE: il-prodotti kollha li jkunu waslu fl-aħħar tal-ħajja ta' l-użu
tagħhom, iridu jiġu rritornati għand Zebra għar-riċiklaġġ. Għal aktar tagħrif dwar kif
għandek tirritorna l-prodott, jekk jogħġbok żur: http://www.zebra.com/weee.
Nederlands: Voor klanten in de EU: alle producten dienen aan het einde van
hun levensduur naar Zebra te worden teruggezonden voor recycling. Raadpleeg
http://www.zebra.com/weee voor meer informatie over het terugzenden van
producten.
Polski: Klienci z obszaru Unii Europejskiej: Produkty wycofane z eksploatacji
nale¿y zwróciæ do firmy Zebra w celu ich utylizacji. Informacje na temat zwrotu
produktów znajduj¹ siê na stronie internetowej http:/www.zebra.com/weee.
Português: Para clientes da UE: todos os produtos no fim de vida devem ser
devolvidos à Zebra para reciclagem. Para obter informações sobre como devolver
o produto, visite: http://www.zebra.com/weee.
Românesc: Pentru clienţii din UE: Toate produsele, la sfârşitul duratei lor de
funcţionare, trebuie returnate la Zebra pentru reciclare. Pentru informaţii despre
returnarea produsului, accesaţi: http://www.zebra.com/weee.
Slovenčina: Pre zákazníkov z krajín EU: Všetky výrobky musia byť po uplynutí
doby ich životnosti vrátené spoločnosti Zebra na recykláciu. Bližšie informácie o
vrátení výrobkov nájdete na: http://www.zebra.com/weee.
Slovenski: Za kupce v EU: vsi izdelki se morajo po poteku življenjske dobe
vrniti podjetju Zebra za reciklažo. Za informacije o vraèilu izdelka obišèite:
http://www.zebra.com/weee.
Suomi: Asiakkaat Euroopan unionin alueella: Kaikki tuotteet on palautettava
kierrätettäväksi Zebra-yhtiöön, kun tuotetta ei enää käytetä. Lisätietoja tuotteen
palauttamisesta on osoitteessa http://www.zebra.com/weee.
Svenska: För kunder inom EU: Alla produkter som uppnått sin livslängd måste
returneras till Zebra för återvinning. Information om hur du returnerar produkten
finns på http://www.zebra.com/weee.
Türkçe: AB Müşterileri için: Kullanım süresi dolan tüm ürünler geri dönüştürme
için Zebra'ya iade edilmelidir. Ürünlerin nasıl iade edileceği hakkında bilgi için
Software Support
Zebra wants to ensure that customers have
the latest entitled software at the time of device* purchase in
order to keep the device operating at peak performance levels.
To conrm that your Zebra device* has the latest entitled
software available at the time of purchase, visit:
www.zebra.com/support. Check for the
latest software from Support > search for the device and
select Support > Software Downloads.
If your device does not have the latest entitled software as of
your device purchase date, e-mail Zebra at
entitlementservices@zebra.com and ensure you include
the following essential device information:
• Model number
• Serial number
• Proof of purchase
• Title of the software download you are requesting.
If it is determined by Zebra that your device is entitled to the
latest version of software as of the date you purchased your
device, you will receive an e-mail containing a link directing
you to a Zebra Web site to download the appropriate software.
* This applies to Zebra Mobile Computing devices and select
Advanced Data Capture devices.
Ergonomic
Recommendations
Caution: In order to avoid or minimize the potential
risk of ergonomic injury follow the
recommendations below. Consult with your local
Health & Safety Manager to ensure that you are
adhering to your company’s safety programs to
prevent employee injury.
• Reduce or eliminate repetitive motion
• Maintain a natural position
• Reduce or eliminate excessive force
• Keep objec ts that are used
frequently within easy reach
• Perform tasks at correct heights
• Reduce or eliminate vibration
• Reduce or eliminate direct pressure
• Provide adjustable workstations
• Provide adequate clearance
• Provide a suitable working environment
• I mprove work procedures
RECOMMENDED USAGE GUIDE -
OPTIMUM BODY POSTURE
Low scanning Extended range scanning
Alternate left
and right knees
Avoid extreme wrist angles
Avoid bending and reaching
AVOID BENDING
Upright body posture
AVOID EXTREME
WRIST ANGLES
MT
All Zebra devices are designed to be compliant with rules and regulations in locations they
are sold and will be labeled as required.
Local language translations are available at the following website: www.zebra.com/support.
Any changes or modications to Zebra equipment, not expressly approved
by Zebra, could void the user’s authority to operate the equipment.
CAUTION:
Only use Zebra approved and UL Listed accessories, battery packs and battery chargers.
Do NOT attempt to charge damp/wet mobile computers or batteries. All components must be dry
before connecting to an external power source.
Wireless Device Country Approvals
Regulatory markings, subject to certication, are applied to the device signifying the radio(s) is/are approved for use
in the following countries: United States, Canada, Japan, China, S. Korea, Australia, and Europe 1.
Please refer to the Zebra Declaration of Conformity (DoC) for details of other country markings.
This is available at http://www.zebra.com/doc.
Note 1: For 2.4GHz or 5GHz Products: Europe includes, Austria, Belgium, Bulgaria, Czech Republic, Cyprus, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Liechtenstein, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Slovak Republic, Slovenia, Spain, Sweden, Switzerland and the United Kingdom.
Operation of the device without regulatory approval is illegal.
Frequency of Operation – FCC and IC
5 GHz Only
The use in the UNII (Unlicensed National Information Infrastructure) band 1 5150-5250 MHz band is
restricted to Indoor Use Only; any other use will make the operation of this device illegal.
2.4 GHz Only
The available channels for 802.11 b/g operation in the US are Channels 1 to 11. The range of channels is limited by rmware.
2000
Series
Health and Safety Recommendations
Warnings for Use of Wireless Devices
Please observe all warning notices with regard to the usage of wireless devices
Safety in Hospitals
Wireless devices transmit radio frequency energy and may aect medical electrical equipment.
Wireless devices should be switched o wherever you are requested to do so in hospitals, clinics or health care
facilities. These requests are designed to prevent possible interference with sensitive medical equipment.
Pacemakers
Pacemaker manufacturers recommended that a minimum of 15cm (6 inches) be maintained between a handheld
wireless device and a pacemaker to avoid potential interference with the pacemaker. These recommendations
are consistent with independent research and recommendations by Wireless Technology Research.
Persons with Pacemakers:
• Should ALWAYS keep the device more than 15cm (6 inches) from their pacemaker when turned ON.
• Should not carry the device in a breast pocket.
• Should use the ear furthest from the pacemaker to minimise the potential for interference
• If you have any reason to suspect that interference is taking place, turn OFF your device.
Other Medical Devices
Please consult your physician or the manufacturer of the medical device, to determine if the operation of your
wireless product may interfere with the medical device.
RF Exposure Guidelines
Safety Information
Reducing RF Exposure – Use Properly
Only operate the device in accordance with the instructions supplied.
International
The device complies with internationally recognized standards covering human exposure to electromagnetic
elds from radio devices.
EU
Handheld Devices
To comply with EU RF exposure requirements, this device must be operated in the hand with a minimum
separation distance of 20 cm or more from a person’s body. Other operating congurations should be avoided.
For information on “International” human exposure to electromagnet elds refer to the Zebra
Declaration of Conformity (DoC) at http://www.zebra.com/doc.
US and Canada
Handheld Devices
To comply with FCC RF exposure requirements, this device must be operated in the hand with a minimum
separation distance of 20 cm or more from a person’s body. Other operating congurations should be avoided.
Ukraine: This equipment corresponds to requirements of the Technical Regulation No. 1057, 2008 on restrictions
as to the use of some dangerous substances in electric and electronic devices.
For Australia Only:
For Australia Only. This warranty is given by Zebra Technologies Asia Pacic Pte. Ltd., 71 Robinson Road,
#05-02/03, Singapore 068895, Singapore. Our goods come with guarantees that cannot be excluded under
the Australia Consumer Law. You are entitled to a replacement or refund for a major failure and
compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods
repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major
failure.
Zebra Technologies Corporation Australia’s limited warranty above is in addition to any rights and remedies
you may have under the Australian Consumer Law. If you have any queries, please call Zebra Technologies
Corporation at +65 6858 0722. You may also visit our website: http://www.zebra.com for the most updated
warranty terms.
REGULATORY INFORMATION
Batteries
Charging
To charge the device battery, the battery and charger temperatures must be between + 32 º F and + 104 º F (0 º C and + 40 º C).
Please follow the local regulations when disposing of re-chargeable batteries.
Taiwan - Recycling
EPA (Environmental Protection Administration) requires dry battery producing or importing rms in accordance
with Article 15 of the Waste Disposal Act are required to indicate the recycling marks on the batteries used in
sales, giveaway or promotion. Contact a qualied Taiwanese recycler for proper battery disposal.
Battery Information
Zebra rechargeable battery packs are designed and constructed to the highest standards within the industry.
However, there are limitations to how long a battery can operate or be stored before needing replacement. Many
factors aect the actual life cycle of a battery pack, such as heat, cold, harsh environmental conditions and severe
drops.
When batteries are stored over six (6) months, some irreversible deterioration in overall battery quality may occur.
Store batteries at half of full charge in a dry, cool place, removed from the equipment to prevent loss of capacity,
rusting of metallic parts and electrolyte leakage. When storing batteries for one year or longer, the charge level
should be veried at least once a year and charged to half of full charge.
Replace the battery when a signicant loss of run time is detected.
Standard warranty period for all Zebra batteries is 30 days, regardless if the battery was purchased separately
or included as part of the mobile computer or bar code scanner. For more information on batteries, visit:
http://www.zebra.com/batterybasics
Battery Safety Guidelines
• The area in which the units are charged should be clear of debris and combustible materials or chemicals.
Particular care should be taken where the device is charged in a non commercial environment.
• Follow battery usage, storage, and charging guidelines found in the user's guide.
• Improper battery use may result in a re, explosion, or other hazard.
• To charge the mobile device battery, the battery and charger temperatures must be
between +32 º F and +104 º F (0 º C and +40 º C)
• Do not use incompatible batteries and chargers. Use of an incompatible battery or charger may present a risk
of re, explosion, leakage, or other hazard. If you have any questions about the compatibility of a battery or
a charger, contact Zebra support.
• For devices that utilize a USB port as a charging source, the device shall only be connected to products that
bear the USB-IF logo or have completed the USB-IF compliance program.
• Do not disassemble or open, crush, bend or deform, puncture, or shred.
• Severe impact from dropping any battery-operated device on a hard surface could cause the battery to overheat.
• Do not short circuit a battery or allow metallic or conductive objects to contact the battery terminals.
• Do not modify or remanufacture, attempt to insert foreign objects into the battery, immerse or expose to water
or other liquids, or expose to re, explosion, or other hazard.
• Do not leave or store the equipment in or near areas that might get very hot, such as in a parked vehicle or
near a radiator or other heat source. Do not place battery into a microwave oven or dryer.
• Battery usage by children should be supervised.
• Please follow local regulations to promptly dispose of used re-chargeable batteries.
• Do not dispose of batteries in re.
• Seek medical advice immediately if a battery has been swallowed.
• In the event of a battery leak, do not allow the liquid to come in contact with the skin or eyes. If contact has
been made, wash the aected area with large amounts of water and seek medical advice.
• If you suspect damage to your equipment or battery, contact Zebra support to arrange
for inspection.
Radio Frequency Interference Requirements- FCC
a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference in
a residential installatio. This equipment generates, uses and can radiate radio
FOR HOME OR OFFICE USE
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment o and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help.
Radio Transmitters (Part 15)
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Radio Frequency Interference Requirements- Canada
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Radio Transmitters
For RLAN Devices:
The use of 5 GHz RLAN’s, for use in Canada, have the following restrictions:
• Restricted Band 5.60 – 5.65 GHz
This device complies with RSS 210 of Industry & Science Canada. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Label Marking: The Term "IC:" before the radio certication only signies that Industry Canada technical
specications were met.
Marking and European Economic Area (EEA)
Note: This equipment has been tested and found to comply with the limits for
AVOID REACHING
Statement of Compliance
Zebra hereby declares that this radio equipment is in compliance with Directive 2011/65/EU and 1999/5/EC or
2014/53/EU (2014/53/EU supersedes 1999/5/EC from 13th June 2017). The full text of the EU Declaration of
Conformity is available at the following internet address: http://www.zebra.com/doc
Japan (VCCI) - Voluntary Control Council for Interference
この装置は、情報処理装置等電波障害自主規制協議会（ＶＣＣＩ）の基準に基づくクラスB情報技術装置です。
この装置は、家庭環境で使用することを目的としていますが、この装置がラジオやテレビジョン受信機に近接
して使用されると、受信障害を引き起こすことがあります。 取扱説明書に従って正しい取り扱いをして下さい。
This is a Class B product based on the standard of the Voluntary Control Council for Interference from Information
Technology Equipment (VCCI). If this is used near a radio or television receiver in a domestic environment, it may
cause radio interference. Install and use the equipment according to the instruction manual
Other Countries
Brazil
1. Este equipamento não tem direito à proteção contra interferência prejudicial e não pode causar interferência em
sistemas devidamente autorizados.
2. Este produto está homologado pela Anatel de acordo com os procedimentos regulamentados para avaliação da
conformidade de produtos para telecomunicações e atende aos requisitos técnicos aplicados, incluindo os
limites de exposição da Taxa de Absorção Especíca referente a campos elétricos, magnéticos e eletromagnéticos
de radiofrequência.
Valores de SAR medidos:
Corpo: 0.0 W/kg
Mexico - Restrict Frequency Range to: 2.450 – 2.4835 GHz.
Sri Lanka - Restrict Frequency Range to: 2.400 – 2.430 GHz.
Eurasian Customs Union
Евразийский Таможенный Союз
Данный продукт соответствует требованиям знака EAC.
Taiwan -
臺灣
低功率電波輻射性電機管理辦法
第十二條
經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、
加大功率或變更原設計之特性及功能。
第十四條
低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，
並改善至無干擾時方得繼續使用。
前項合法通信，指依電信規定作業之無線電通信。
低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。
限制頻率範圍是： 2.400 - 2.4835 GHz。 最大發射功率: 27dBm
5.250 - 5.350 GHz。 最大發射功率: 17dBm
5.725 - 5.850 GHz。 最大發射功率: 24dBm
2.4GHz： 11個通道
5GHz： 8個通道
在5.25-5.35 赫頻帶內操作之無線資訊傳輸設備，限於室內使用。
Laser Labels
In accordance with Clause 5. IEC 825 and EN60825, the following information is provided to the user
Laser Devices
Complies with 21CFR1040.10 & 1040.11 except for deviations pursuant to Laser Notice NO. 50, dated June 24,
2007 and IEC/EN 60825-1:2007 and/or IEC/EN 60825-1:2014.
The laser classication is marked on one of the labels on the device.
Class 1 Laser devices are not considered to be hazardous when used for their intended purpose. The following
statement is required to comply with US and international regulations:
Caution: Use of controls, adjustments or performance of procedures other than those specied herein may result
in hazardous laser light exposure.
Class 2 laser scanners use a low power, visible light diode. As with any very bright light source, such as the sun,
the user should avoid staring directly into the light beam. Momentary exposure to a Class 2 laser is not known
to be harmful.
CAUTION- CLASS 2 LASER LIGHT WHEN OPEN. DO NOT
STARE INTO THE BEAM. ATTENTION- LUMIÉRE LASER
EN CAS D'OUVERTURE. NE PAS REGARDER DANS LE FAISCEAU.
VORSICHT- LASERLICHT KLASSE 2, WENN ABDECKUNG GEÖFFNET.
NICHT IN DEN STRAHL BLICKEN.
意：打开时及联锁失效时有激光辐射 勿直视光束
Zebra Technologies Corporation
Lincolnshire, IL U.S.A.
http://www.zebra.com
ZEBRA and the stylized Zebra hea are trademarks of Zebra Technologies Corporation, registered in many
jurisdictions worldwide. All other trademarks are the property of their respective owners.
© 2017-2019 Zebra Technologies Corporation and/or its affiliates. All rights reserved.
72-117308-05 Revision A May 2019
MT
2000
Series
The use of 5GHz RLAN’s throughout the EEA, have the following restriction:
• 5.15 - 5.35 GHz is restricted to indoor use only.
http://www.zebra.com/mt2000
Loading...