Chevy Tahoe Installation Instructions
1) Carefully remove the trim panel as shown using trim panel removal tools to avoid
damage.
2) There are many retaining clips so work slowly all around the edges to release .
For more information, contact your local Motion Reseller or Motion Representative.
© 2011 Motion Computing, Inc. All rights reserved. Motion and Motion Computing are registered trademarks of Motion Computing, Inc
.
www.MotionComputing.com
Chevy Tahoe Installation Instructions
3) Remove the upper right radio retaining screw as shown.
4) Remove the upper left radio retaining screw as shown.
For more information, contact your local Motion Reseller or Motion Representative.
© 2011 Motion Computing, Inc. All rights reserved. Motion and Motion Computing are registered trademarks of Motion Computing, Inc
.
www.MotionComputing.com
Chevy Tahoe Installation Instructions
5) Remove the lower right radio retaining screw as shown.
6) Remove the lower left radio retaining screw as shown.
For more information, contact your local Motion Reseller or Motion Representative.
© 2011 Motion Computing, Inc. All rights reserved. Motion and Motion Computing are registered trademarks of Motion Computing, Inc
.
www.MotionComputing.com
Chevy Tahoe Installation Instructions
7) Remove both heater control retaining screws. Only right hand screw is pictured.
8) Remove both switch panel retaining screws. Only left hand screw is pictured.
For more information, contact your local Motion Reseller or Motion Representative.
© 2011 Motion Computing, Inc. All rights reserved. Motion and Motion Computing are registered trademarks of Motion Computing, Inc
.
www.MotionComputing.com
Chevy Tahoe Installation Instructions
9) Remove the left hand fascia retaining screw as shown.
10) Remove the right hand fascia retaining screw as shown.
For more information, contact your local Motion Reseller or Motion Representative.
© 2011 Motion Computing, Inc. All rights reserved. Motion and Motion Computing are registered trademarks of Motion Computing, Inc
.
www.MotionComputing.com
Chevy Tahoe Installation Instructions
11) Remove the heater and switch panel units as shown.
12) Remove the radio head unit disconnecting all of the wiring looms shown.
For more information, contact your local Motion Reseller or Motion Representative.
© 2011 Motion Computing, Inc. All rights reserved. Motion and Motion Computing are registered trademarks of Motion Computing, Inc
.
www.MotionComputing.com
Chevy Tahoe Installation Instructions
13) Remove the right hand chassis retaining bolt as shown.
14) Remove the left hand chassis retaining bolt as shown.
For more information, contact your local Motion Reseller or Motion Representative.
© 2011 Motion Computing, Inc. All rights reserved. Motion and Motion Computing are registered trademarks of Motion Computing, Inc
.
www.MotionComputing.com
Chevy Tahoe Installation Instructions
15) Fit the Left Hand Side Bracket 032-02-0301 as shown. Temporarily secure in place using
two screws removed in steps 4 and 6.
16) Ensure that the bracket is pushed firmly in the direction of the arrow as you tighten the
screws.
For more information, contact your local Motion Reseller or Motion Representative.
© 2011 Motion Computing, Inc. All rights reserved. Motion and Motion Computing are registered trademarks of Motion Computing, Inc
.
www.MotionComputing.com
Chevy Tahoe Installation Instructions
17) Fit two self tapping screws 039-02-0423 in the positions indicated in red below. Note
that the picture below only shows one screw.
For more information, contact your local Motion Reseller or Motion Representative.
© 2011 Motion Computing, Inc. All rights reserved. Motion and Motion Computing are registered trademarks of Motion Computing, Inc
.
www.MotionComputing.com
Chevy Tahoe Installation Instructions
18) Fit the fascia retaining screw removed in step 9 as shown. Note that the metal of the
bracket is designed to bend and will be pulled in by the screw. Ensure that it is fully
tightened.
For more information, contact your local Motion Reseller or Motion Representative.
© 2011 Motion Computing, Inc. All rights reserved. Motion and Motion Computing are registered trademarks of Motion Computing, Inc
.
www.MotionComputing.com
Chevy Tahoe Installation Instructions
19) Fit one self tapping screws 039-02-0423 into the side as shown.
20) Fit one self tapping screws 039-02-0423 into the side as shown.
For more information, contact your local Motion Reseller or Motion Representative.
© 2011 Motion Computing, Inc. All rights reserved. Motion and Motion Computing are registered trademarks of Motion Computing, Inc
.
www.MotionComputing.com
Chevy Tahoe Installation Instructions
21) Refit the chassis retaining bolt removed in step 14 as shown.
22) Note that the metal of the bracket is designed to bend and will be pulled in by the
screw. Ensure that it is fully tightened.
For more information, contact your local Motion Reseller or Motion Representative.
© 2011 Motion Computing, Inc. All rights reserved. Motion and Motion Computing are registered trademarks of Motion Computing, Inc
.
www.MotionComputing.com
Chevy Tahoe Installation Instructions
23) Remove the lower screw which was temporarily fitted in step 15.
24) Remove the upper screw which was temporarily fitted in step 15.
For more information, contact your local Motion Reseller or Motion Representative.
© 2011 Motion Computing, Inc. All rights reserved. Motion and Motion Computing are registered trademarks of Motion Computing, Inc
.
www.MotionComputing.com
Chevy Tahoe Installation Instructions
25) Repeat steps 15 to 24 for the Right Side Bracket 032-02-0300 pictured below.
For more information, contact your local Motion Reseller or Motion Representative.
© 2011 Motion Computing, Inc. All rights reserved. Motion and Motion Computing are registered trademarks of Motion Computing, Inc
.
www.MotionComputing.com
Chevy Tahoe Installation Instructions
26) Replace the cable looms removed in step 12 and refit the radio head unit.
27) Refit the four radio retaining screws as shown.
For more information, contact your local Motion Reseller or Motion Representative.
© 2011 Motion Computing, Inc. All rights reserved. Motion and Motion Computing are registered trademarks of Motion Computing, Inc
.
www.MotionComputing.com
Chevy Tahoe Installation Instructions
28) Refit the heater control unit and secure with the left hand retaining screw as shown.
29) Refit the right hand retaining screw to the heater control unit as shown.
For more information, contact your local Motion Reseller or Motion Representative.
© 2011 Motion Computing, Inc. All rights reserved. Motion and Motion Computing are registered trademarks of Motion Computing, Inc
.
www.MotionComputing.com
Chevy Tahoe Installation Instructions
30) Refit the switch panel unit and secure with the left hand retaining screw as shown.
31) Refit the right hand retaining screw to the switch panel unit as shown.
For more information, contact your local Motion Reseller or Motion Representative.
© 2011 Motion Computing, Inc. All rights reserved. Motion and Motion Computing are registered trademarks of Motion Computing, Inc
.
www.MotionComputing.com
Chevy Tahoe Installation Instructions
32) The vehicle should now look like the below photograph and is ready to have the trim
panel refitted.
Note that it may be necessary to bend out the two metal tabs indicated slightly to make
fitting of the trim panel easier.
For more information, contact your local Motion Reseller or Motion Representative.
© 2011 Motion Computing, Inc. All rights reserved. Motion and Motion Computing are registered trademarks of Motion Computing, Inc
.
www.MotionComputing.com
Chevy Tahoe Installation Instructions
33) Once the trim panel is securely back in place, fit the Front Bracket 032-02-0299 as
shown.
Use four screws TD503712 and four lock washers TD503481 in the positions shown and
tighten securely.
For more information, contact your local Motion Reseller or Motion Representative.
© 2011 Motion Computing, Inc. All rights reserved. Motion and Motion Computing are registered trademarks of Motion Computing, Inc
.
www.MotionComputing.com
Chevy Tahoe Installation Instructions
34) Fit the Docking Station / Tilt & Rotate
Assembly to the front bracket as shown using
the provided M8 fasteners.
NOTE:- It may be necessary to temporarily
remove the rubber edge strip to allow for
correct fitment.
Ensure that the location lugs are correctly
engaged before final tightening to prevent
unwanted rotation.
For more information, contact your local Motion Reseller or Motion Representative.
© 2011 Motion Computing, Inc. All rights reserved. Motion and Motion Computing are registered trademarks of Motion Computing, Inc
.
www.MotionComputing.com
Loading...