Zebra MNT-VC80-ADPB1-1 Adapter Bracket Kit for Honeywell U-Mount

Introduction
Screw
Split Lock Washer
Flat Washer
Adapter Bracket (2) M6X1X17 (4)
Mounting Bracket
Note: Dependent on the desired height, attach the U-Mount Bracket to either the top two or bottom two holes located on the Adapter Bracket.
Adapter Bracket
M6X1X17 (4)
Scanner Holder
M6X1X17 (4)
Mounting Bracket
Adapter Bracket
M6X1X17 (4)
Scanner Holder
This installation guide provides instruction on how to install the Adapter Bracket Kit (P/N: MNT-VC80-ADPB1-1) to attach the VH10 or the VC80 to the Honeywell U-Mount Bracket.
WARNING! The vehicle computer and bracket must be firmly
CAUTION Mounts used in industrial or vibration generating
secured to a surface that can support the vehicle computer’s weight.
Always use four 11mm holes with M10 screws to mount the bracket to the desired location. Using different holes and screws may cause damage and/or injury.
environments may be subjected to fatigue, stress, and/or part wear. A periodic inspection of the mounting hardware and mounts should be performed to ensure parts are retightened to the correct torque, free from fractures, excessive wear, and/or other environmental damage. Any parts found to be unsafe should be removed and replaced immediately. After inspection or replacement of parts, readjust the mount as required.
Contents
The Adapter Bracket kit includes:
Adapter Bracket (quantity: 2)
M6X1X17 screws and washers (quantity: 8 each)
Installation guide (quantity: 1)
Required Tools
Socket and Torque wrench for the M6 and M10 screws.
ADAPTER BRACKET KIT
FOR HONEYWELL U-MOUNT
INSTALLATION GUIDE
3. Install the subassembly to the Mounting Bracket using the
M6X1X17 screws and washers. Adjust the VC to the desired angle. Torque the M6 screws to 3.9 Nm (34.5 in-lbs).
Scanner Holder
The Scanner Holder attachment (P/N: KT-SCANMNT-VC80-R) is not included in the Adapter Bracket kit and must be purchased separately.
To attach the Scanner Holder:
1. Install the Adapter Bracket on one side of VC using the M6X1X17 screws and washers.
2. Install the Adapter Bracket and Scanner Holder subassembly on the other side of the VC using the M6X1X17 screws. Torque the screws to 3.9 Nm (34.5 in-lbs).
Installation
WARNING! Always disconnect the VC from all battery and
A/C power before servicing components.
To install the Adapter Bracket:
1. Screw the Adapter Brackets onto the VC using the M6X1X17 screws and washers.
a. Insert the Split Lock Washer on the screw. b. Insert the Flat Washer on the screw. c. Torque the screws to 3.9 Nm (34.5 in-lbs).
2. Mount the Mounting Bracket (P/N: VM1010BRKT) in the desired
location using the M10X1.5X50 screws, split lock washers, and flat washers (not included in the Adapter Bracket kit). Torque the screws to 42 Nm (31 ft-lbs).
Zebra Technologies Corporation, Inc. 3 Overlook Point Lincolnshire, IL 60069, U.S.A. http://www.zebra.com
Zebra and the stylized Zebra head are trademarks of ZIH Corp., registered in many jurisdictions worldwide. All other trademarks are the property of their respective owners. © 2016 Symbol Technologies LLC, a subsidiary of Zebra Technologies Corporation. All rights reserved.
3. Mount the Mounting Bracket (P/N: VM1010BRKT) in the desired location using the M10X1.5X50 screws and washers (not included in the Adapter Bracket kit). Torque the screws to 42 Nm (31 ft-lbs).
4. Install the subassembly to the Mounting Bracket using the M6X1X17 screws and washers. Adjust the VC to the desired angle. Torque the M6 screws to 3.9 Nm (34.5 in-lbs).
MN-002934-01 Rev A 10/2016
Loading...