CR0078-P Cradles
Quick Reference Guide
2 CR0078-P Cradles
Zebra reserves the right to make changes to any product to improve reliability,
function, or design.
Zebra does not assume any product liability arising out of, or in connection with,
the application or use of any product, circuit, or application described herein.
No license is granted, either expressly or by implication, estoppel, or otherwise
under any patent right or patent, covering or relating to any combination, system,
apparatus, machine, material, method, or process in which Zebra products might
be used. An implied license exists only for equipment, circuits, and subsystems
contained in Zebra products.
This product may include Software, Commercial Third Party Software, and
Publicly Available Software. Refer to the Product Reference Guide for complete
copyright, conditions and disclaimer information.
Warranty
For the complete Zebra hardware product warranty statement, go to:
http://www.zebra.com/warranty.
For Australia Only
This warranty is given by Zebra Technologies Asia Pacific Pte. Ltd., 71 Robinson
Road, #05-02/03, Singapore 068895, Singapore. Our goods come with
guarantees that cannot be excluded under the Australia Consumer Law. You are
entitled to a replacement or refund for a major failure and compensation for any
other reasonably foreseeable loss or damage. You are also entitled to have the
goods repaired or replaced if the goods fail to be of acceptable quality and the
failure does not amount to a major failure.
Zebra Technologies Corporation Australia’s limited warranty above is in addition
to any rights and remedies you may have under the Australian Consumer Law. If
you have any queries, please call Zebra Technologies Corporation at
+65 6858 0722. You may also visit our website: http://www.zebra.com for the most
updated warranty terms.
Quick Reference Guide 3
Introduction
The cordless scanner cradle model CR0078 (part CR0078-P) acts as a stand,
charger and host communication interface for DS6878 cordless scanners. The
CR0078-P cradle receives data from the scanner via a Bluetooth radio, and sends
that data to the host through an attached cable. The cradle also charges the
scanner’s internal battery pack when the scanner is inserted. The cradle must be
powered by an external power supply.
This document provides basic instructions on setting up and using the cradle.
Configurations
This guide includes information on the following configurations:
• CR0078-PC1F09BWR - Cordless scanner cradle; hands-free presentation,
charging, Bluetooth, FIPS, healthcare white
• CR0078-PC1F007WR - Cordless scanner cradle; hands-free presentation,
charging, Bluetooth, FIPS, twighlight black
Accessories
The following equipment is needed:
• Power Supply (see Power Supply on page 11 for detailed requirements)
•Line Cord
• Host Cable
IMPORTANT For USB interface, only use a cable with a shielded modular
plug (for example: CBA-U21-S07ZAR or CBA-U29-S15ZAR)
Save the shipping container for storing or shipping. Inspect all equipment for
damage. If anything is damaged or missing, call an authorized Customer Support
Representative immediately.
4 CR0078-P Cradles
Front
Back
Charging/
Communication
Contacts
Latch
LED
Pager Button
Rubber Foot
Rubber Foot
Rubber Foot
Rubber Foot
Power Port
Host Port
Host Cable Groove
Power Cable Groove
Host Cable Groove
Power Cable Groove
Cable Support Hook
Cable Support Hook
Mounting Hole
Mounting Hole
Cradle Parts
Quick Reference Guide 5
Power Port
Host Port
Power Port
Host Port
Connect to
appropriate host
Power
Alternate
Host Groove
Alternate
Power Groove
If the cradle does not recognize the host, d
isconnect the power supply,
then reconnect after connecting the host cable.
Cradle Connections
Important: Connect the interface cable and power supply in the following order to
ensure proper operation of the scanner and cradle:
1. Insert the interface cable into the cradle’s host port.
2. Connect the other end of the interface cable to the host.
3. Connect the power supply to the cradle’s power port.
4. Connect the appropriate cable to the power supply and AC power source.
5. Thread the interface cable over the cable support hook (see Cradle Parts on
page 4) and run the host and power cables into their respective cable grooves.
6. If necessary, scan the appropriate host bar code (for non-autodetected
interfaces). Refer to the DS6878 Product Reference Guide, p/n 72-131700-xx.
Changing the Host Interface
To connect to a different host, or to the same host through a different cable:
1. Unplug the power supply from the cradle.
2. Unplug the interface cable from the host.
3. Connect the interface cable to the new host, or the new interface cable to the
4. Reconnect the power supply.
5. If necessary, scan the appropriate host bar code with a paired scanner (for
existing host.
non-autodetected interfaces). Refer to the DS6878 Product Reference Guide,
p/n 72-131700-xx.
Loading...