Zebra 10/100 User Manual

47619L-006

ZebraNet®

10/100 Print Server

User Guide

© 2011 ZIH Corp. The copyrights in this manual and the software and/or firmware in the label printer described

therein are owned by ZIH Corp. Unauthorized reproduction of this manual or the software and/or firmware in the
label printer may result in imprisonment of up to one year and fines of up to $10,000 (17 U.S.C.506). Copyright
violators may be subject to civil liability.

This product may contain ZPL

®

, ZPL II®, and ZebraLink™ programs; Element Energy Equalizer® Circuit; E3®; and

Monotype Imaging fonts. Software © ZIH Corp. All rights reserved worldwide.
ZebraLink and all product names and numbers are trademarks, and Zebra, the Zebra logo, ZPL, ZPL II, Element

Energy Equalizer Circuit, and E

3

Circuit are registered trademarks of ZIH Corp. All rights reserved worldwide.

All other brand names, product names, or trademarks belong to their respective holders. For additional trademark
information, please see “Trademarks” on the product CD.

Proprietary Statement This manual contains proprietary information of Zebra T echnologies Corporation and its

subsidiaries (“Zebra Technologies”). It is intended solely for the information and use of parties operating and
maintaining the equipment described herein. Such proprietary information may not be used, reproduced, or disclosed
to any other parties for any other purpose without the express, written permission of Zebra Technologies Corporation.

Product Improvements Continuous improvement of products is a policy of Zebra Technologies Corporation.

All specifications and designs are subject to change without notice.

Liability Disclaimer Zebra Technologies Corporation takes steps to ensure that its published Engineering

specifications and manuals are correct; however, errors do occur. Zebra Technologies Corporation reserves the right
to correct any such errors and disclaims liability resulting therefrom.

Limitation of Liability In no event shall Zebra Technologies Corporation or anyone else involved in the creation,

production, or delivery of the accompanying product (including hard ware and software) be liab le for any damages
whatsoever (including, without limitation, consequential damages including loss of busin ess profi ts, business
interruption, or loss of business information) arising out of the use of, the results of use of, or inability to use such
product, even if Zebra Technologies Corporation has been advised of the possibility of such damages. Some
jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation
or exclusion may not apply to you.

Part Number: 47619L-006 Rev. A

Contents

About This Document . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Who Should Use This Document. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

How This Document Is Organized . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Contacts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Document Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Related Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

1 • Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Browser Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Supported Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Compatibility. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Installation Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

External 10/100 PS Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

2 • Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

External 10/100 PS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

Before You Begin. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

Illustration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

Installation Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

Internal 10/100 PS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

02/01/2011 ZebraNet® 10/100 Print Server User Guide 47619L-006 Rev. A

4

Contents

3 • Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

Default User ID and Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

Printing a Configuration Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

Assigning an IP Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30

With Dynamic Host Configuration Protocol (DHCP) . . . . . . . . . . . . . . . . .30

Without DHCP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30

Assigning an IP Address with DHCP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

Assigning an IP Address via ZebraNet Bridge. . . . . . . . . . . . . . . . . . . . . .31

Assigning an IP address from the Printer LCD . . . . . . . . . . . . . . . . . . . . .31

Assigning an IP address via a Telnet session . . . . . . . . . . . . . . . . . . . . . .32

Setting and Monitoring Alerts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34

ZebraLink Alerts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34

Using ZebraNet Bridge. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36

Using WebView . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36

Checking 10/100 PS Configuration Settings . . . . . . . . . . . . . . . . . . . . . . . . . .39

Using ZebraNet Bridge. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39

Using WebView . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39

Enabling Protocols. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43

Using WebView . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43

Defaulting the 10/100 PS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46

Using WebView . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46

Using ZebraNet Bridge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47

Using the Test Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47

4 • Printing Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Berkeley Software Distribution (BSD)-Style Print Queue. . . . . . . . . . . . . . . . .50

Configuring the Print Queue. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50

System V Queue Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51

Configuring Operating System V Queue for ZebraNet Printing . . . . . . . . .51

Prerequisites . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51

UNIX Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51

5 • Using Printing Protocols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

IPP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54

FTP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55

47619L-006 Rev. A ZebraNet® 10/100 Print Server User Guide 02/01/2011

Contents

A • ZebraLink WebView . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

WebView . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58

Home Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58

View Printer Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60

View and Modify Printer Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61

Directory Listing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67

Printer Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68

Print Server Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70

Zebra BASIC Interpreter (ZBI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70

B • 10/100 Print Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

10/100 PS Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72

Status and Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72

Print Server Status. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .81

Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .83

Restore. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .84

Setting the Primary Network Print Server . . . . . . . . . . . . . . . . . . . . . . . . .85

TCP/IP Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .89

5

C • Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93

Control Panel Menu Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .94

Wired Network Parameters on the LCD. . . . . . . . . . . . . . . . . . . . . . . . . . .94

D • Hardware Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97

Troubleshooting the 10/100 PS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .98

Resetting to Factory Default . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .98

10/100 PS Status Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .98

10/100 PS Network Status/Activity Indicator . . . . . . . . . . . . . . . . . . . . . . .99

ZebraNet Bridge Discovery or Configuration Problems. . . . . . . . . . . . . .100

Unable to Print . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .100

Unable to Configure Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .102

HP JetAdmin or HP Web JetAdmin . . . . . . . . . . . . . . . . . . . . . . . . . . .102

E • Frequently Asked Questions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103

Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111

02/01/2011 ZebraNet® 10/100 Print Server User Guide 47619L-006 Rev. A

Contents

Notes • ___________________________________________________________________

__________________________________________________________________________

__________________________________________________________________________

__________________________________________________________________________

__________________________________________________________________________

__________________________________________________________________________

__________________________________________________________________________

__________________________________________________________________________

__________________________________________________________________________

__________________________________________________________________________

6

47619L-006 Rev. A ZebraNet® 10/100 Print Server User Guide 02/01/2011

About This Document

This section provides you with contact information, documen t struc ture and organization, and
additional reference documents.

Contents

Who Should Use This Document. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

How This Document Is Organized . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Contacts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Document Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Related Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

02/01/2011 ZebraNet® 10/100 Print Server User Guide 47619L-006 Rev. A

About This Document

8

Who Should Use This Document

Who Should Use This Document

This User Guide is intended to be used by any person who will install and work with the
10/100 PS.

How This Document Is Organized

This User Guide is set up as follows:

Section Description

Introduction This chapter provides a high-level overview of the

Getting Started This chapter provides you with information and

10/100 PS device, installation types, standard
network configurations, and how to work with
10/100 PS.

procedures for working with the most frequently
used 10/100 PS features.

Installation This chapter provides information on how to

install the 10/100 PS.

Printing Configurations This chapter provides information and instructions

on configuring your printer for use with a BSD or
System V Queue.

Using Printing Pro toc ol s In this chapter, you are given steps to set up your

10/100 PS to support Internet Printing Protocol
(IPP) and File Transfer Protocol (FTP).

ZebraLink WebView This appendix describes the ZebraLink WebView

functionality on your ZebraLink-enabled printer
with a 10/100 PS.

10/100 Print Server This appendix provides you with details on the

10/100 PS features that were not covered in the
chapter Getting Started on page 27.

Hardware Troubl eshooting This section provides you with solutions to k nown

issues.

Frequently Asked Questions This section provides a group of frequently asked

questions (FAQs) about 10/100 PS.

Glossary This appendix is a list of terms and associated

definitions.

47619L-006 Rev. A ZebraNet® 10/100 Print Server User Guide 02/01/2011

Contacts

About This Document

Technical Support via the Internet is available 24 hours per day, 365 days per year.

Web Site: www.zebra.com
E-mail Back Technical Library:

E-mail address: [e-mail]
Subject line: Emaillist

Self Service Knowledge Base: www.zebra.com/knowledgebase
Online Case Registration: www.zebra.com/techrequest

Contacts

9

Which Department

Do You Need?

Regional Headquarters Zebra Technologies Corporation

475 Half Day Road, Suite 500
Lincolnshire, IL 60069 USA

T: [phone]
Toll-f ree [phone]
F: [phone]

Technical Support

For questions on the
operation of Zebra
equipment and software,
please call your distributor.
For additional assistance,
contact us.

Please have your model and
serial numbers available.

Repair Service
Department

For back-to-base service
and repair.

Technical Training
Department

For Zebra product training
courses.

Inquiry Department

For product literature and
distributor and dealer
information.

Customer Service
Department (US)

Internal Sales
Department (UK)

For printers, parts, media,
and ribbon, please call your
distributor or contact us.

Key:

T: Telephone
F: Facsimile
E: E-mail

T: +1 877 ASK ZEBRA (275 9327)
F: [phone]

Hardware: [e-mail]
Software: [e-mail]

Kiosk printers:

T: [phone]
E: [e-mail]

T: +1 877 ASK ZEBRA (275 9327)
F: [phone]

E: [e-mail]
To request a repair in the U.S.,

go to www.zebra.com/repair
T: [phone]

T: [phone]
F: [phone]

E: [e-mail]

T: +1 877 ASK ZEBRA (275 9327)
E: [e-mail]

T: +1 877 ASK ZEBRA (275 9327)
E: [e-mail]

The Americas

.

Europe, Middle East,

and Africa

Zebra Technologies Europe
Limited
Dukes Meadow
Millboard Road
Bourne End
Buckinghamshire, SL8 5XF
United Kingdom

T: [phone]
F: [phone]

T: [phone]
F: [phone]

E: [e-mail]

T: [phone]
F: [phone]

New requests: [e-mail]
Status updates:

[e-mail]

T: [phone]
F: [phone]

E: [e-mail]

T: [phone]
F: [phone]

E: [e-mail]

T: [phone]
F: [phone]

E: [e-mail]

Asia Pacific

and India

Zebra Technologies Asia Pacific
Pte. Ltd.
120 Robinson Road
#06-01 Parakou Building
Singapore 068913

T: + 65 6858 0722
F: [phone]

T: [phone]
F: [phone]

E: China: [e-mail]

All other areas:

[e-mail]

T: [phone]
F: [phone]

E: China: [e-mail]

All other areas:

[e-mail]

T: + 65 6858 0722
F: [phone]

E: China: [e-mail]

All other areas:

[e-mail]

E: China:

[e-mail]

All other areas:

[e-mail]
m

T: [phone]
F: [phone]

E: China: [e-mail]

All other areas:

[e-mail]

02/01/2011 ZebraNet® 10/100 Print Server User Guide 47619L-006 Rev. A

About This Document

10

Document Conventions

Document Conventions

The following conventions are used throughout this document to convey certain information:

Alternate Color (online only) Cross-references contain links to other sections in this guide.
If you are viewing this guide online, click the blue text to jump to its location.

Command Line Examples All command line examples appear in Courier New font.
For example, type the following to get to the Post-Install scripts in the

Ztools

Files and Directories All file names and directories appear in Courier New font. For
example, the

Cautions, Important, Note, and Example

Caution • Warns you of the potential for electrostatic discharge.

bin directory:

Zebra<version number>.tar file and the /root directory.

Caution • Warns you of a potential electric shock situation.

Caution • Warns you of a situation where excessive heat could cause a burn.

Caution • Advises you that failure to take or avoid a specific action could result in physical

harm to you.

Caution • Advises you that failure to take or avoid a specific action could result in physical

harm to the hardware.

Caution • Advises you need to wear protective eye wear.

Important • Advises you of informatio n that is essential to complete a task.

Note • Indicates neutral or positive information that emphasizes or supplements important

points of the main text.

Example • Provides an example, often a scenario, to better clarify a section of text.

47619L-006 Rev. A ZebraNet® 10/100 Print Server User Guide 02/01/2011

About This Document

1

2

Document Conventions

Illustration Instructions Used when an illustration contains either information about a
dialog box or step(s) to accomplish in a dialog box.

One illustration instruction identifies a section of the dialog box and the other shows steps to
follow .

11

Set Permanent text-box.

1

a. In the Set Permanent text-box, type in the print

2

server’s IP address.

b. When you are finished, click OK.

02/01/2011 ZebraNet® 10/100 Print Server User Guide 47619L-006 Rev. A

About This Document

12

Related Documents

Related Documents

The following documents might be helpful references:

• ZebraNet Wireless Print Server User Guide

• ZPL II® Programming Guide For x.10 through x.13 Firmware

• ZPL II

• ZebraNet Bridge Enterprise User Guide

®

Programming Guide For x.14 Firmware and Above

47619L-006 Rev. A ZebraNet® 10/100 Print Server User Guide 02/01/2011

1

Introduction

This chapter provides a high-level overview of the 10/100 PS device, installation types,
standard network configurations, and how to work with 10/100 PS.

Contents

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Browser Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Supported Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Compatibility. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Installation Types. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

External 10/100 PS Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

02/01/2011 ZebraNet® 10/100 Print Server User Guide 47619L-006 Rev. A

Introduction

14

Overview

Overview

Requirements

Browser Support

The 10/100 Print Server (PS) is an optional factory- or field-installed device that connects the
network and your ZebraLink-enabled prin ter. The 10/100 PS provides you with a web browser
as a user interface for printer and 10/100 PS settings. If you use the ZebraNet Bridge, you can
easily access the specialized features of a ZebraLink-enabled printer. For details, see the
ZebraNet Bridge Enterprise User Guide.

Important • You can download the most recent version of ZebraNet Bridge Enterprise from

www.zebra.com/utilities.

This section lists the minimum requirements for 10/100 PS, which includ e browsers,
supported services, address administration protocols, hardware, and firmware.

• HTML v3.2 or higher

Supported Services

•Raw TCP •FTP

•HTTP •UDP

•LPR/LPD •Telnet

• SNMPv1 • SMTP

•POP3 •WINS

•IPP v1.0 •ARP

Address Administration Protocols

•DHCP

•BootP

•RARP

•Gleaning

•Permanent

47619L-006 Rev. A ZebraNet® 10/100 Print Server User Guide 02/01/2011

Hardware

The following table indicates which printers are compatible with the 10/100 Print Server
(10/100 PS) options.

Introduction

Requirements

15

Printers

External *

Internal

Field Upgrade

Internal
Factory

105SL™ •••
R110Xi™ •••
R170Xi™ •••
PAX4™ series•••
R110PAX4™•••
S4M™ • • * • *
XiIIIPlus™•••
Xi4™ • † †
R110Xi4™ • † †
Z4Mplus™•••
Z6Mplus™•••
ZM400™ • † †
ZM600™ • † †
RZ400™ • † †
RZ600™ • † †

NOTES: * For additional information on print server firmware versions, see Firmware on page 16.

† For information on these print servers, see the ZebraNet 10/100 Internal Print Server User Guide

(p/n: 14197L-xxx) available at www.zebra.com/manuals.

02/01/2011 ZebraNet® 10/100 Print Server User Guide 47619L-006 Rev. A

16

Introduction

Requirements

Firmware

The S4M printers and all external print servers are available with several versions of print
server firmware. All other printers will use print server firmware version 1.01.x.

To determine the proper firmware version, first determine your hardware version.

To locate your hardware version, perform the following:

1. Which type of printer and print server do you have?

If you have… Then…

Any printer with an
External print server

An S4M printer with an
Internal print server

All other printers with an
Internal print server

a. Look at the side of the print server.
b. See Figure 1 on page 17. Your version is listed on the

Compliance label.

c. Your hardware version number is either blank or V2.

•If your hardware version is blank, assume this means
V1 (version 1). You will need firmware version

1.01.x.

•If your hardware version is V2, you will need
firmware version 2.01.x.

a. Look at the back plate of the printer.
b. See Figure 2 on page 17. Your version is listed on the

thin Compliance label on the bracket of the wired print
server.

c. The version number is shown as blank or V2.

•If your hardware version is blank, assume this means
V1 (version 1). You will need firmware version

1.01.x.

•If your hardware version is V2, you will need
firmware version 2.01.x.

a. Your hardware version will be V1.
b. You will need firmware version 1.01.x.

47619L-006 Rev. A ZebraNet® 10/100 Print Server User Guide 02/01/2011

Introduction

EN: ZZ:ZZ:ZZ:ZZ:ZZ:ZZ

UID #

SN YYYYYYY

PN XXXXX

FOR HOME, OFFICE,
COMMERCIAL, OR
INDUSTRIAL USE

Tested to Comply

With FCC Standards

This Class B digital apparatus
complies with Canadian ICES-003

V2

1

2

SN YYYYYYY EN: ZZ:ZZ:ZZ:ZZ:ZZ:ZZ

V2

1

2

Requirements

Figure 1 • External 10/100 Print Server Sample Compliance Label

Sample Compliance label

1

Location of hardware version

2

17

Figure 2 • Internal 10/100 Print Server Sample Compliance Label

Sample Compliance label

1

(vertically oriented on the back of the printer)
Location of hardware version

2

02/01/2011 ZebraNet® 10/100 Print Server User Guide 47619L-006 Rev. A

Introduction

18

Compatibility

Compatibility

This section identifies the various components that are compatible with 10/100 PS.

ZebraNet wireless print servers 10/100 PS is fully compatible with the wireless print
servers.

®

Software IBM

: Tivoli® v7.1.3, HP®: Web JetAdmin™ v7.0, OpenView™ v6.4, and any
SNMP management application via Zebra Management Information Base (MIB) all work with
10/100 PS.

47619L-006 Rev. A ZebraNet® 10/100 Print Server User Guide 02/01/2011

Installation Types

10/100 PS can be factory- or field-installed, as follows:

Factory Factory installations are for new Zebra printers that are built with the internal
10/100 PS option.

Field Field installations are for Zebra printers already in the field that do not have the
10/100 PS device installed. The 10/100 PS option can be installed on existing printers, as
follows:

• External 10/100 PS — attaches to the printer parallel port

Internal 10/100 PS — for the appropriate Zebra printers, this option connects directly

•
to the main logic board

Caution • A qualified service technician must perform this installation.

Introduction

Installation Types

19

02/01/2011 ZebraNet® 10/100 Print Server User Guide 47619L-006 Rev. A

Introduction

20

External 10/100 PS Specifications

External 10/100 PS Specifications

General Specifications

Network Connection Ethernet 10BASE-T and 100BASE-T UTP RJ-45

Printer Connection Bi-directional, IEEE-1284 Centronics parallel port

User Interface LED activity indicators:

Height (external dimensions) 1.2 in. 30.48 mm
Width (external dimensions) 2.8 in. 71.12 mm
Length (external dimensions) 3.2 in. 81.28 mm
Weight 2.7 oz 77 g
Electrical Maximum 450mA at 5.25VDC Power prov ided by

connection Half and Full Duplex Communications

(Compatibility, Nibble, and ECP)

• bi-color display of operational status

• bi-color display of speed and network activity

the printer (Centronics pin 18, 5VDC at 450mA)

Temperature Operating 32° to 104°F 0° to 40°C

Storage –40° to 140°F –40° to 60°C

Relative Humidity Operating 20% to 85%, non-condensing

Storage 5% to 85%, non-condensing

Agency Approvals Agency Approvals

• IEC 60950

• EN 55022, class B

• EN 55024

• AS/NZS3548
Agency Marks

•FCC - B

•ICES-003

•VCCI

•C-Tick

47619L-006 Rev. A ZebraNet® 10/100 Print Server User Guide 02/01/2011

Installation

This chapter provides information on how to install the 10/100 PS.

2

Contents

External 10/100 PS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Before You Begin. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Illustration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Installation Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Internal 10/100 PS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

02/01/2011 ZebraNet® 10/100 Print Server User Guide 47619L-006 Rev. A

Installation

22

External 10/100 PS

External 10/100 PS

This section provides you with an illustration of the ex ternal 10/100 PS and the steps required
for its installation. For a list of compatib le printers, see Hardware on page 15.

Before You Begin

Important • In order to take advantage of all features described in this manual, you must

download firmware X.14 or later.

To upgrade you printer firmware, complete these steps:

1. If your printer has firmware x.12 firmware, you must upgrade your printer firmware to

2. To upgrade your firmware, visit the Zebra Web site:

Note • Not all printers support firmware X.1 4 or later. On those printers, the features

for this print server will be limited.

version x.14.x or higher.

www.zebra.com/firmware

3. Confirm that the upgrade was successful:

If... Then...

Your printer has an LCD Look at the lower right-hand corner and confirm the

version of firmware that is on your printer.

Y our p rinter does not have
an LCD

Print out a configuration label to see the version of
firmware that is on your printer.

47619L-006 Rev. A ZebraNet® 10/100 Print Server User Guide 02/01/2011

Illustration

1

5

4

3

2

Figure 3 shows an external 10/100 PS. When necessary, refer back to this illustration during

the installation steps.

Figure 3 • External 10/100 PS

Installation

External 10/100 PS

23

Parallel connector

1

Network status LED

2

10/100 PS Status LED

3

Test button

4

Ethernet connector

5

For more details on status indicators, see 10/100 PS Network Status/Activity Indicator

on page 99.

02/01/2011 ZebraNet® 10/100 Print Server User Guide 47619L-006 Rev. A

Installation

Parallel
Port
Connector

Printer Back

24

External 10/100 PS

Installation Instructions

To install an external 10/100 PS, complete these steps:

1. Turn off (O) the printer.

2. On the back of the printer, connect the 10/100 PS device to the parallel port.

Figure 4 shows the location and provides an enlarged illustration of the parallel port.

Figure 4 • Rear of 105SL Printer

3. Secure the wire locks.

4. On the back of the 10/100 PS, connect an active Ethernet cable to the RJ-45 connector

Ethernet connector.

5. Turn on (I) the printer.

The 10/100 PS performs a Power On Self-Test (POST). This takes about 45 seconds.
During the POST, the 10/100 PS Status LED (just below the TEST button) turns red and
flashes on and off. Once the POST is successfully completed and the 10/100 PS is fully
initialized, the 10/100 PS Status LED turns green.

For more details on status indicators, see 10/100 PS Status Indicator on page 98.

Note • If there is not an active Ethernet cable attached to the 10/100 PS, the LED indicator

turns red and slowly flashes on and off.

6. To check the status of the 10/100 PS, press the Test button located on the back of the

10/100 PS.
This prints out a configuration label of the 10/100 PS. To see a sample label, see Figure 5

on page 25.

47619L-006 Rev. A ZebraNet® 10/100 Print Server User Guide 02/01/2011

Installation

External 10/100 PS

In order to print the 10/100 PS configuratio n label, the correct medi a size must be loaded in the
printer. For all printers, the minimum label length is 4 in. (101.60 mm). Table 1 shows the
minimum label widths needed to print a 10/100PS configuration label with different DPI
printheads.

Table 1 • Label Width

DPI Inches mm

600 1.25 31.75
300 2.50 63.50
211 3.69 93.73
150 5.0 127.00

This is an example of a 10/100 PS configuration label.

Figure 5 • 10/100 PS Configuration Label

25

02/01/2011 ZebraNet® 10/100 Print Server User Guide 47619L-006 Rev. A

Installation

26

Internal 10/100 PS

Internal 10/100 PS

T o in stall an intern al 10/10 0 PS, see the installation instructions on the Connectivity Solutions
CD.

47619L-006 Rev. A ZebraNet® 10/100 Print Server User Guide 02/01/2011

3

Getting Started

This chapter provides you with information and procedures for working with the most
frequently used 10/100 PS features.

Contents

Before You Begin. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Default User ID and Password. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Printing a Configuration Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Assigning an IP Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

With Dynamic Host Configuration Protocol (DHCP) . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Without DHCP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Assigning an IP Address with DHCP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Assigning an IP Address via ZebraNet Bridge. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Assigning an IP address from the Printer LCD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Assigning an IP address via a Telnet session . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Setting and Monitoring Alerts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

ZebraLink Alerts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Using ZebraNet Bridge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Using WebView . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Checking 10/100 PS Configuration Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Using ZebraNet Bridge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Using WebView . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Enabling Protocols. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Using WebView . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Defaulting the 10/100 PS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Using WebView . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Using ZebraNet Bridge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Using the Test Button. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

02/01/2011 ZebraNet® 10/100 Print Server User Guide 47619L-006 Rev. A

Getting Started

28

Before You Begin

Before You Begin

10/100 PS offers many features, but how you access and work with them is dependent on your
environment.

Default User ID and Password

Throughout the procedures in this document, there are some features that require the default
User ID and/or default password. If you are prompted, these are the defaults:

Printing a Configuration Label

Before you begin, you need to get information from the 10/100 PS configuration label.

Important • Make sure the printer is turned off (O).

• User ID:

• Password: 1234

admin

In order to print the 10/100 PS configuratio n label, the correct medi a size must be loaded in the
printer. For specific information on media sizes, see Table 1 on page 25.

To print a 10/100 PS configuration label, complete these steps:

1. Turn on (I) the printer and let it complete its power-up cycle.

2. When the POST cycle is complete, press the Test button and hold it in for a few seconds

before you release it.
A 10/100 PS configuration label prints. Y our configuration label looks similar to Figure 6

on page 29.

47619L-006 Rev. A ZebraNet® 10/100 Print Server User Guide 02/01/2011

Figure 6 • 10/100 PS Configuration Label

Getting Started

Before You Begin

29

3. From the configuration label, you need to look for these numbers:

• ADDRESS (IP address)

• SUBNET MASK

• DEFAULT GATEWAY

• SERIAL NUMBER

• HARDWARE ADDRESS (MAC address)

4. On the configuration label that prints out for your 10/100 PS device, circle the

aforementioned settings. You can now proceed to Assigning an IP Address on page 30.

02/01/2011 ZebraNet® 10/100 Print Server User Guide 47619L-006 Rev. A

Getting Started

30

Assigning an IP Address

Assigning an IP Address

Before you can begin working with 10/100 PS, you must get or assign an IP address for the
10/100 PS device.

The four different ways to assign an IP address are:

• ZebraNet Bridge

•DHCP

•Printer LCD

•Telnet

Important • For specific information on the default User ID and/or default password, see

Default User ID and Password on page 28.

With Dynamic Host Configuration Protocol (DHCP)

If your network uses DHCP, your 10/100 PS device is assigned a temporary IP address.

Note • Check with your Network Administrator to see whether your network uses DHCP.

Without DHCP

If your network does not use a dynamic IP addressing system (such as DHCP), you need to set
a permanent IP address for the 10/100 PS device. ZebraNet Bridge may be used to set the IP
address.

47619L-006 Rev. A ZebraNet® 10/100 Print Server User Guide 02/01/2011