Page 1
Handheld Computer
Z-2065 series ( Version 3.00 )
User’s Manual
ZEBEX INDUSTRIES INC.
WWW.ZEBEX.COM
jkl
4
7
stu
1
abc
ESC
ENT
SP
F2
F4
F3
9
vwx
8
yz
65mno pqr
BS
F1
3
2
def ghi
ENT
SCAN
RESET
0
@
Page 2
ZEBEX INDUSTRIES INC.
Subject Version Date Page
Z-2065 series User’s Manual 3.00 2010/3/19 2 / 69
Editorial Record
Version Date of edited Page Content
Ver 2.00 2009/3/2 9
Revise the picture of Package contents
Ver 2.00 2009/3/2 10
Revise the picture of Cradle Package
Ver 2.00 2009/3/2 11,12
Revise the picture Purchaseable accessories
Ver 2.00 2009/3/2 26~52
Adding the instruction of Using PowerPack
Ver 2.00 2009/3/2 53~56
Adding the
picture
of
How to order
Ver 3.00 2010/1/25 26~49 Updated PowerPack Functions and pictures
Ver 3.00 2010/3/16 30~39 Adding GPRS User Manual
Ver 3.00 2010/3/19 1~26 Adding New Photo for Z-2065
Page 3
ZEBEX INDUSTRIES INC.
Subject Version Date Page
Z-2065 series User’s Manual 3.00 2010/3/19 3 / 69
Table of Contents
Preface
About This Manual.................................................................................................5
Symbols used in this manual......................................................................5
Copyright................................................................................................................6
Safety Information.................................................................................................6
Laser Safety ..................................................................................................6
Safety Operation...........................................................................................7
Federal Communication Commission (FCC) Statement ...........................8
Unpacking
Package Contents..................................................................................................9
Optional Parts......................................................................................................10
Cradle package
............................................................................................10
Purchaseable Accessories ........................................................................11
General Guide......................................................................................................13
Getting Start
Inserting the Battery............................................................................................15
Remove the Battery.............................................................................................15
Charging the Battery...........................................................................................16
Charging by cable
.......................................................................................16
Charging by cradle
......................................................................................16
Charging the battery sep arately in the cradle..........................................17
System Reset.......................................................................................................19
Using the Warm reset function..................................................................19
Using the Cold reset function....................................................................19
PC System Requirements ...................................................................................20
Connecting To a PC.............................................................................................20
Connecting via the RS232..........................................................................20
Connecting via USB Cradle.......................................................................21
Connecting the Z-2065 directly via USB....................
錯誤! 尚未定義書籤。
Inserting SD Card ................................................................................................22
Remove the SD Card...........................................................................................22
About The Product ..............................................................................................23
Prerequisites...............................................................................................23
Specifications .............................................................................................24
Using Barcode Scanner
Scanning Barcodes.............................................................................................25
Using RFID Scanner
Scanning RFID.....................................................................................................26
UZEBEX Hand-Held Terminal GPRS User’s Guide
Making New Connection.....................................................................................30
Set Connection Properties..................................................................................32
Phone Number.....................................................................................................34
Set Dial Properties...............................................................................................35
Page 4
ZEBEX INDUSTRIES INC.
Subject Version Date Page
Z-2065 series User’s Manual 3.00 2010/3/19 4 / 69
Connect to GPRS Service...................................................................................37
Disconnect GPRS Service ..................................................................................39
Using Zebex Power Pack
Backlight...............................................................................................................40
Calculator.............................................................................................................42
File Transfer.........................................................................................................43
File Transfer Operation................................................................................44
Preload Manager ……………………………………………………………………...46
Preload Operation.......................................................................................47
Switch...................................................................................................................50
Scan Manager ….……………………………………………………………………. .52
Backup/Restore ...................................................................................................56
Firmware Information..........................................................................................58
Function Key Manager........................................................................................59
How to order………………………………………………………………………………..64
Page 5
ZEBEX INDUSTRIES INC.
Subject Version Date Page
Z-2065 series User’s Manual 3.00 2010/3/19 5 / 69
Preface
About This Manual
Thank you for your purchase of the ZEBEX Z-2065 series handheld
computer. ZEBEX Z-2065 series product is at the forefront of
handheld computer technology, and this manual will provide the
necessary information on the many and varied options available to
you.
The Z-2065 series product is a compact, ergonomic and durable
handheld computer. It is designed with an integrated 802.11b/g
wireless communication, 1D/2D barcode scanner, touch screen and
29-keys keypad. The design is complies with IP64 regulations and
ideal for the mobile worker as it simple and easy to use anywhere
along a supply chain.
Symbols used in this manual
A triangular shape indicates you should exercise
caution.
A circle shape indicates something you should not to
do.
A black circle indicates something you must to do.
A note symbol indicates you the information that is
important and you should be observed.
Page 6
ZEBEX INDUSTRIES INC.
Subject Version Date Page
Z-2065 series User’s Manual 3.00 2010/3/19 6 / 69
Copyright
ZEBEX Industries Inc. makes no warranty of any kind with regard to
this material. Including but not limited to the imply warranties of
merchantability and fitness for a particular purpose. ZEBEX Industries
Inc. shall not be liable for errors contained herein or for incidental
consequential damages in connection with the furnishing,
Performance or use of this product.
ZEBEX Industries Inc. will be under no liability in respect of any defect
arising from fair wear and tear, willful damage, negligence, abnormal
working conditions, failure to follow the instructions and warnings, or
misuse or alteration or repair of the products without written approval.
No part of this document may be reproduced, transmitted, stored in a
retrieval system, transcribed or translated into any language or
computer language in any form or by any means electronic,
mechanical, magnetic, optical, chemical, manual or otherwise, with
express writ- ten consent and authorization.
We reserve the right to make changes in product design without
reservation and without notification. The material in this guide is for
information only and is subject to change without notice.
ZEBEX is a registered trademark of ZEBEX INDUSTRIES INC.
© Copyright 2008 ZEBEX.
Safety Information
Your safety is of the utmost importance so please observe and follow
the following guidelines that allow you to use the scanner in a safe
and responsible way.
Laser Safety
The Z-2065 series handheld computer complies with safety standard
IEC825-1(1993) for a Class 2 laser product. It also complies with
U.S.21CFR1040 as applicable to a Class II laser product. Avoid
staring at direct laser light as the laser beam may hurt your eyes.
LASER BEAM
Never look directly into the laser beam. Doing so can cause
serious eye damage.
Page 7
ZEBEX INDUSTRIES INC.
Subject Version Date Page
Z-2065 series User’s Manual 3.00 2010/3/19 7 / 69
Safety Operation
WARNING
Disassembly and Modification
Never try to disassemble or modify the device in any way.
All
servicing should be carried out by qualified Zebex personnel or
Zebex- approved engineers.
Interior Parts and Components
Never touch interior high voltage parts or components. Doing
so creates the danger of electrical shock.
Drop and Knock the Device
Be careful when using the device; do not drop or knock the
device as irreversible damage to the unit may occur.
Extreme temperature
Do not operate the device under extreme temperature.
Battery and Charger
The use of third-party battery or charger may either damage the
device or shorten the life of the device.
CAUTION
Dropping and Damage
Should the drop the device and damage it, immediately turn off
the power and contact your original dealer or an authorized
ZEBEX service provider. Continued use creates the danger of
fire and electrical shock.
Abnormal Conditions
Should the device become hot or start to emit smoke or an
original dealer or an authorized ZEBEX service provider.
Continued use creates the danger of fire and electrical shock.
Foreign Objects
Should any foreign matter ever get into the device, immediately
turn off the power and contact your original dealer or an
authorized ZEBEX service provider. Continued use creates the
danger of fire and electrical shock.
Moisture
Keep the device away from vases, planters, cups, glasses and
other containers of liquid. Also keep it away from metal. Water
and metal getting into the device creates the danger of fire and
electrical shock.
Page 8
ZEBEX INDUSTRIES INC.
Subject Version Date Page
Z-2065 series User’s Manual 3.00 2010/3/19 8 / 69
Federal Communication Commission (FCC)
Statement
You are cautioned that changes or modifications not expressly
approved by the part responsible for compliance could void the user’s
authority to operate the equipment.
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates uses and can radiate radio frequency energy and, if not
installed and used in the accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC RF Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth
for an uncontrolled environment. End users must follow the specific
operating instructions for satisfying RF exposure compliance. This
transmitter must not be co-located or operated in conjunction with any
other antenna or transmitter.
Page 9
ZEBEX INDUSTRIES INC.
Subject Version Date Page
Z-2065 series User’s Manual 3.00 2010/3/19 9 / 69
Unpacking
Package Contents
AC Adapter
Z-2065 series
Mobile Data Terminal
Stylus Pen
RS-232 DB9 (F) Cable
Hand Strip
USB cable
(Terminal connect to PC USB port)
Hand strip Holder
Battery Pack
Sling for stylus Pen
Page 10
ZEBEX INDUSTRIES INC.
Subject Version Date Page
Z-2065 series User’s Manual 3.00 2010/3/19 10 / 69
Optional Parts
Cradle package
Docking Cradle RS232 cable
AC Adapter
USB cable
(Cradle to USB)
Page 11
ZEBEX INDUSTRIES INC.
Subject Version Date Page
Z-2065 series User’s Manual 3.00 2010/3/19 11 / 69
Purchaseable Accessories
RS232 Cable
AC Adapter
RS-232 DB9 (F) Cable
Britain Plug head
USB cable (Cradle to USB)
U.S. Plug head
Battery Pack
Australia Plug head
Stylus Pen
Europe Plug head
Page 12
ZEBEX INDUSTRIES INC.
Subject Version Date Page
Z-2065 series User’s Manual 3.00 2010/3/19 12 / 69
Hand Strip for stylus Pen
Sling for stylus Pen
Hand strip Holder
Page 13
ZEBEX INDUSTRIES INC.
Subject Version Date Page
Z-2065 series User’s Manual 3.00 2010/3/19 13 / 69
jkl4
7
stu
1abc
ESC
ENT
SP
F2
F4
F3
9
vwx8
yz
65mno pqr
BS
F1
32
def ghi
ENT
SCAN
RESET
0
@
General Guide
1 LED indicator
Indicates the status of read bar code or battery charge :
Green for successful read barcode or full charge of battery.
Red for battery just on charging.
2 Buzzer Outputs operation confirmation tones.
3 LED indicator for WI-FI Flashes in red when operating via WLAN communication
4 LCD screen Display various data when a program is being run.
5 Stroke keys
A total of 29 keys are provided to turn power ON or OFF
and other operations.
6 Reset switch (inside the hole)
Use reset needle (take off the other side of stylus pen
cover) to press the RESET switch located inside the hole.
7 Scan button For Barcode reading.
8 Mini USB port This port is for USB communication with PC.
9 Ear Jack Listens to the voice.
10 Mini SD I/O card slot Install the Mini SD I/O card
11 Scan windows Emits a laser for bar code reading.
12 RS-232 port This port is for RS-232 communication with PC
13 Stylus pen For touch screen operation and press RESET switch.
14 Hand strip Protects the Handheld Terminal to drop.
15 Battery Main battery
16 Sling
Sling for stylus pen
Page 14
ZEBEX INDUSTRIES INC.
Subject Version Date Page
Z-2065 series User’s Manual 3.00 2010/3/19 14 / 69
4 jkl F2
F3
F4
SP
stu
7
yz
98vwx
5mno 6pqr
ENT
BS
F1
1
abc
ESC
2
def
3ghi
ENT
RESET
SCAN
0
@
Arrow Arrow keys
Press these to move around the screen.
ENT Enter key Press to confirm entries or commands.
0-9 Alphanumeric keypad Press to enter
numerical or alphabetical
data.
F1-F4 Function keys Press to access function keys 1-4.
BS Backspace key
Press
to move cursor and deletes the previous character
each time.
Power/Backlight on key
1. Press to turn the power on.
2. Press more then 3 seconds for turn the terminal power
off and go into the suspend mode.
3. Press to turn the LCD backlight on when it is off.
ESC Escape key Press to perform a cancel action.
SCAN Scan key Press and hold to scan a barcode.
SF/Fn Shift key
The key is used in combination with other keys to type
special characters or perform other function keys.
1. Press after SF/Fn key and press Up key to turn
the
input method into upper alphabetical.
2. Press after SF/Fn key and press Down key to turn
the
input method into lower alphabetical.
3. Press after SF/Fn key and press Left or Right key to
turn
the input method into numerical.
4. Press after SF/Fn key and press F1-F4 key to perform
F5 - F8 key.
TAB Tab key Press to add a tab indention.
SP Space key Press to add a space character.
Page 15
ZEBEX INDUSTRIES INC.
Subject Version Date Page
Z-2065 series User’s Manual 3.00 2010/3/19 15 / 69
Getting Started
Inserting the Battery
Insert the battery pack as shown and watch the battery direction..
Remove the Battery
Push the side lock to pick up the battery pack.
Page 16
ZEBEX INDUSTRIES INC.
Subject Version Date Page
Z-2065 series User’s Manual 3.00 2010/3/19 16 / 69
Charging the Battery
The Li-ion rechargeable battery can be charged while inserted in the
device itself or independently via the recharging slot at the back of the
cradle.
Charging by cable
Connect the charging cable and AC adaptor as shown.
Charging by cradle
USB Interface
AC Power
Adapter
Jack In
RS232/COM port Interface
Cradle - rear view
Page 17
ZEBEX INDUSTRIES INC.
Subject Version Date Page
Z-2065 series User’s Manual 3.00 2010/3/19 17 / 69
Left LED
Right LED
Cradle - front view
Cradle LEDs
Left LED - The LED lit when a battery is inserted into the rear battery
slot of the cradle for recharge. It remains lit until the
charge is complete.
Right LED - The LED lit when the cradle is connected to AC power.
Charging the battery separately in the cradle
Insert the battery into the compartment at the rear of the cradle.
Page 18
ZEBEX INDUSTRIES INC.
Subject Version Date Page
Z-2065 series User’s Manual 3.00 2010/3/19 18 / 69
Connect the power jack to the cradle and plug AC adapter into the
socket.
NOTES
When charging the battery for the first time, charge for at least
12 hours prior to use.
Page 19
ZEBEX INDUSTRIES INC.
Subject Version Date Page
Z-2065 series User’s Manual 3.00 2010/3/19 19 / 69
6
pqr5
mno
0
8vwx
stu
7
SP
yz
9
F4
F3
ENTENT
1
2
def
jkl
4
abc
ESC
F1
3
ghi
F2
BS
SCAN
RESET
0
@
System Reset
Using the Warm reset function
Warm reset function allows you to return the device to the default
settings, wile not wiping all data from the memory.
Insert the needle into the reset hole as shown and press
down
gently
, to
reset the device
.
Using the Cold reset function
Cool reset function allows you to return the device to the factory settings,
wile wiping all data from the memory.
Press down and hold the power key and Insert the needle into the reset
hole
to cold reset the device
.
WARNING
Cold reset will erase ALL pre-configured data on the scanner.
Check
carefully to make sure you have uploaded all important
files to
your PC before proceeding with the reset.
Page 20
ZEBEX INDUSTRIES INC.
Subject Version Date Page
Z-2065 series User’s Manual 3.00 2010/3/19 20 / 69
PC System Requirements
Windows XP Operating System
64 MB RAM
50 MB free HDD space
Interface : USB / RS-232 ports
WLAN transmitter (optional)
Bluetooth transmitter/receiver (optional)
Connecting To a PC
In order to use the software supplied with the Z-2065, the mobile data
terminal must be connected to a PC.
Connecting via the RS232
In order for the sync software to work properly, the cradle must be
connected to your computer’s COM port. Attach one end of the RS232
cable to the RS232/COM interface connector on the cradle and the other
to the COM1 port on your PC.
1. Or can use attach one RS-232 cable to connect with your computer’s
COM port directly.
Page 21
ZEBEX INDUSTRIES INC.
Subject Version Date Page
Z-2065 series User’s Manual 3.00 2010/3/19 21 / 69
Connecting via USB Cradle
The cradle must also be connected via one of your PC’s USB ports.
Attach one end of the cable to the USB interface on the cradle and the
other to your PC.
Page 22
ZEBEX INDUSTRIES INC.
Subject Version Date Page
Z-2065 series User’s Manual 3.00 2010/3/19 22 / 69
Inserting SD Card
1. Make sure the power is turn off.
2. Open the SD Slot cover as shown, Insert the SD card.
3. Close the SD slot Cover.
Remove the SD Card
1. Make sure the power is turn off.
2. Open the SD Slot cover as shown, Take off the SD card.
3. Closed the SD slot cover.
Page 23
ZEBEX INDUSTRIES INC.
Subject Version Date Page
Z-2065 series User’s Manual 3.00 2010/3/19 23 / 69
About The Product
ZEBEX Z-2065 WinCE.NET Handheld Computer comes with the one and
only Jacket-module design, and makes most user friendly features to
select as desired. The Jacket-module is a module at the back of device
that is selectable in GPRS, GPS, RFID, WLAN or Bluetooth
communications and 1D or 2D scanning engine, it satisfies all application
from indoor to outdoor and from warehouse to transportation logistics.
Z-2065 qualifies to use in most difficult environments with its rugged
design with IP64 standard.
Further more, its round shape back deisgn allow it to sit in palm fitly for
best operation comfort, and for future expansion, it has a gun grip design
to broaden its application into more categories. Z-2065 has an
unbeatable technology and ergonomic design that upgrades your with
power.
Prerequisites
Skills Required
The following skills are required by developers aiming to develop
application software for the ZEBEX Z-2065 series.
● Windows programming
● Good knowledge of one or more of the following:
* Visual C++
* Visual Basic .NET
* Visual studio .NET
* Visual C#
* Active Server Pages and web programming
The following skills or experiences are also desirable.
● Windows CE devices
● ActiveSync
● Something networking experience.
Hardware Required
The following models of the ZEBEX Z-2065 series and the dedicated
options are available.
Page 24
ZEBEX INDUSTRIES INC.
Subject Version Date Page
Z-2065 series User’s Manual 3.00 2010/3/19 24 / 69
Available models and the features:
WLAN GPR S(G) RFID(H)
P/N (device only)
&
B
T
(WL)
1D 2D(SE450 0) 2.5G HF
1 Z-2065WL1
882- 65W100- 000 882-65W100-100
◆◆
2 Z-2065WL2
882- 65W200- 000 882-65W200-100
◆◆
3 Z-2065W1GS
882-65W1GS-000
882-65W1GS-100
◆◆ ◆ ◆
4 Z-2065W2GS
882- 65W2GS-00 0 882-65W2GS-100
◆◆◆◆
5 Z-2065W1GSH
882-65G1SH-000 882-65G1SH-100
◆◆ ◆ ◆◆
6 Z-2065W2GSH
882-65G2SH-000 882-65G2SH-100
◆◆◆◆◆
7 Z-2065W1G
882-65W1G0-000 882-65W1G0-100
◆◆ ◆
8 Z-2065W2G
882- 65W2G0-00 0 882-65W2G0-100
◆◆◆
9 Z-2065W1S
882-65W1S0-000 882-65W1S0-100
◆◆ ◆
10 Z-2065W2S
882- 65W2S0-0 00 882-65W2S0-100
◆◆ ◆
11 Z-2065W1H
882- 65W1H0-0 00 882- 65W1H0-1 00
◆◆ ◆
12 Z-2065W2H
882- 65W2H0-0 00 882-65W2H0-100
◆◆ ◆
Model P/ N(include accessor y)
Barc ode
GPS(S)
Specifications
Model
Z-2065 series
System
CPU
Inter PXA 270 processor (Max. 520MHz)
RAM
128 Mbyte
F-ROM
64 Mbyte
LCD Display
3.5”,
QVGA
240 X 320 TFT
color panel
with touch screen
Operating System
Microsoft Windows CE.NET 5.0
Power Management
Main Battery
3.7V5,000mAH Li-ion rechargeable battery
3.7V 2,200 mAH Li-ion rechargeable
3.7V,
120
mAH, Li-Poly rechargeable battery
Battery Life
8 hours (without wireless communication activated)
Scanning Performance
Scan Engine Symbol SE-955 1D laser engine
Symbol SE-4400
2D image engine (optional)
Light Source
650 nm visible Laser Diode
Scan Rate
100 scans per second
Print Contrast
30% @ UPC/EAN 100%
Decoding Capability
Barcode Symbologies
UPC/ EAN/ JAN, Code 128/EAN 128, Code 39, Code 93,
Interleaved 2 of 5, Discrete 2 of 5, Codabar, MSI/Plessey
Card Slots
1 x
Mini
SD I/O card
Communications / Interfaces
Bluetooth
Bluetooth Class 2
IrDA
Standard IrDA 1.3
USB
USB 2.0
RS-232
Programmable up to 115,200 bps
WLAN
802.11b/g (optional)
Dimensions
190.5 mm (L) x82..8 mm (W) x
50.5 mm
(H)
Page 25
ZEBEX INDUSTRIES INC.
Subject Version Date Page
Z-2065 series User’s Manual 3.00 2010/3/19 25 / 69
Weight
Approx. 480 g (battery included)
Environmental
Operating Te mp .
0°C ~ 50°C
Storage Temp -10°C ~ 60°C
Operating Humidity 10% ~ 70% (non-condensing)
Storage Humidity 5% ~ 70% (non-condensing)
Drop Durability Withstand 1.2m ( 4 feet) drop to concrete
Environmental Sealing IP64 rated sealing
Regulatory Approvals CE & FCC Part 15B, 15 C,CE RF,LVD,ESD
Cradle Single slot USB / RS-232 charging cradle with spare
battery slot
Software &Development
Microsoft
VC
6.0 development environment
Supports SDK for program development
Using Barcode Scanner
Scanning Barcodes
The Z-2065 is a highly versatile tool that can scan a wide range of barcodes but
it is imperative that it is used in the correct manner.
To
scan a barcode:
1. Hold the Z-2065 horizontally and point it directly at the barcode you wish to
scan.
2. Once in the correct position, press the SCAN button.
An audible alarm is heard and the barcode digits will appear on the
LCD screen if the scan is successful.
Page 26
ZEBEX INDUSTRIES INC.
Subject Version Date Page
Z-2065 series User’s Manual 3.00 2010/3/19 26 / 69
Using RFID Scanner (Optional)
Scanning RFID
To open Zebex RFID demo program, you can find program located on
following path: “My Device\Flash Disk\RFID\RFID_ADJ\”.
RFID Scanning Position
RFID scan module was installed in the back of terminals. The devices
can read from 30 to 50mm distance from the back-side of terminals.
To scan a RFID
After opening Zebex RFID demo program, you will see main menu displayed
as below. There are three main functionalities such as “Read UID”, “RW
Page 27
ZEBEX INDUSTRIES INC.
Subject Version Date Page
Z-2065 series User’s Manual 3.00 2010/3/19 27 / 69
15693”, and “RW Mifare”. Please follow below steps to read UID.
Reading UID
1) Select COM port to reading UID, default setting was COM5. Then confirm by pressing
“ Open Port ” button.
2) Select UID type, then confirm by pressing “ Start ” button. Demo program provide three
UID types such as 15693, 14443A, and 14443B.
3) User can also adjust scanning rate by selecting how many msec for scanning once. Then
confirm by clicking “ Timer ” button.
4) After scanning UID, it will be shown on column at the bottom of display. Data in column
can be clear by pressing “ Clear ” button.
5) COM port can be stop by pressing “ Close Port ” button.
6) If user need to switch to another UID type, UID type by can be cancel by pressing
“ Stop ” button. Then user can select another UID type as demand.
RW 15693
On RW 15693 function window, user can read and write information from
RW 15693 UID card:
1) Set up protocol by pressing “ SetProtocol “ button, place UID card within valid range and
press “ CheckUID ”button. The UID will display in the red circle of below diagram.
2) To read data from certain Block, first input the location in column next to Read Block.
Then confirm by pressing “ Read Block ” button. Read Data will appear in column
showed in green circle of below diagram.
3) To write UID from certain Block, first input the location in column next to ” Write
Block ” button, then write the data into the longer column in blue circle. Confirm written
Page 28
ZEBEX INDUSTRIES INC.
Subject Version Date Page
Z-2065 series User’s Manual 3.00 2010/3/19 28 / 69
data by pressing “ Write Block ” button.
4) Information appear at bottom can be clear by pressing “ Clear ” button.
RW Mifare
On RW 15693 function window, user can read and write information from
Mifare UID card:
1) Place UID card within valid range, check UID by pressing “ Open Card ” button. UID
will display in red circle shown in below diagram.
2) To perform read and write commands, please refer to “RW 15693” sections.
Page 29
ZEBEX INDUSTRIES INC.
Subject Version Date Page
Z-2065 series User’s Manual 3.00 2010/3/19 29 / 69
ZEBEX Hand-Held Terminal
GPRS User’s Guide
MakeNewConnection
1. Click Network and Dial-Up Connections in the settings.
Show as below figures.
2. Click Make New Connection to create the new connection.
Show as below figures.
Page 30
ZEBEX INDUSTRIES INC.
Subject Version Date Page
Z-2065 series User’s Manual 3.00 2010/3/19 30 / 69
3. Select the Dial-Up Connection and press Next button to make new
connection. Show as below figure.
4. Press Next button to select the modem.
Page 31
ZEBEX INDUSTRIES INC.
Subject Version Date Page
Z-2065 series User’s Manual 3.00 2010/3/19 31 / 69
SetConnectionProperties
1. Select Internal GPRS Modem and press the Configure button to change the
settings of properties.
2. Change the Baud Rate to 115200 in Port Settings.
Show as below figure.
3. Input the dial string in Call Option. Show as below figure.
Page 32
ZEBEX INDUSTRIES INC.
Subject Version Date Page
Z-2065 series User’s Manual 3.00 2010/3/19 32 / 69
Input +CGDCONT=1,”IP”,”APN” to set the APN for GPRS connection.
For the setting of known APN around the work, please refer below link:
http://www.quickim.com/support/gprs-settings.html
4. Press OK button to complete the settings.
5. Press Next button to set the phone number
Page 33
ZEBEX INDUSTRIES INC.
Subject Version Date Page
Z-2065 series User’s Manual 3.00 2010/3/19 33 / 69
PhoneNumber
1. Set phone number to *99# or *99***1#. This number depends on the service
provider. Show as below figure.
2. Press Finish button to finish the settings of new connection.
Page 34
ZEBEX INDUSTRIES INC.
Subject Version Date Page
Z-2065 series User’s Manual 3.00 2010/3/19 34 / 69
SetDialProperties
1. Double Cli ck the connection.
2. Press the Dial Properties button.
Page 35
ZEBEX INDUSTRIES INC.
Subject Version Date Page
Z-2065 series User’s Manual 3.00 2010/3/19 35 / 69
3. Create new one or select one setting in the Location and press the Edit button.
4. Set the Dialing Patterns as below figure.
Page 36
ZEBEX INDUSTRIES INC.
Subject Version Date Page
Z-2065 series User’s Manual 3.00 2010/3/19 36 / 69
ConnecttoGPRSService
1. Press the Connect button.
2. During the Dial-Up. It shows the status as below figure.
Page 37
ZEBEX INDUSTRIES INC.
Subject Version Date Page
Z-2065 series User’s Manual 3.00 2010/3/19 37 / 69
3. It shows below figure when connected to GPRS service.
Page 38
ZEBEX INDUSTRIES INC.
Subject Version Date Page
Z-2065 series User’s Manual 3.00 2010/3/19 38 / 69
DisconnectGPRSService
1. Double click the connection icon in taskbar.
2. Press the Disconnect button.
Page 39
ZEBEX INDUSTRIES INC.
Subject Version Date Page
Z-2065 series User’s Manual 3.00 2010/3/19 39 / 69
Using the Zebex PowerPack
To save your time and effort in developing applications on Z-2070, ZEBEX
provides it’s owndesign system management tool to called “PowerPack” to let
you control it directly.
The PowerPack management tools which installs in each of our WinCE
product. It is free charge for you. We offer several function for let you control
your device without any programming.
Backlight
This application is set up the Backlight of LCD Panel and Key pad. It allows
operators to set backlight duration, and also backlight can be set up as On &
Off.
The Backlight Setting screen including 3 parts:
1. LCD
2. Keypad
3. Brightness Control Bar
Page 40
ZEBEX INDUSTRIES INC.
Subject Version Date Page
Z-2065 series User’s Manual 3.00 2010/3/19 40 / 69
Page 41
ZEBEX INDUSTRIES INC.
Subject Version Date Page
Z-2065 series User’s Manual 3.00 2010/3/19 41 / 69
1. LCD
The LCD backlight setting.
Auto Mode: This function can be set up the LCD backlight to be auto off as
Device hasn’t been activated for certain interval.
You can set up the Auto off time from 15 sec to 15 min.
Always ON: This function can set up the backlight to be always on
Until the system into suspend mode.
Always OFF: This function can set up the backlight to be always off.
2. Keypad
The Keypad Backlight setting.
Auto Mode: This function can be set up the keypad backlight to be auto off
as device hasn’t been activated for certain interval.
The interval of the time for auto off was fixed on 5 seconds.
Always ON: This function can set up the keypad backlight to be
always on until the system into suspend mode.
Always OFF: This function can set up the backlight to be always off.
3. Brightness Control Bar
The brightness of the backlight can be changed via control bar. Put up to
light and put down to dark.
Page 42
ZEBEX INDUSTRIES INC.
Subject Version Date Page
Z-2065 series User’s Manual 3.00 2010/3/19 42 / 69
Calculator
This calculator function allows operators to add, subtract, multiply, and divide
that simply provide basic logistic function in our daily basis.
The upper zone of the display area displays the memory content, and the
lower zone is key pad.
Button description:
MC : Clear buffer of memory.
MR : Got the value of buffer.
MS : Storage the value to buffer.
M+ : Append the value to the buffer.
CE : Clear the display area to “0”, but keep the value in buffer.
C : Clear the display and the buffer of memory.
+/- : Change the value sign form Plus to Minus or Minus to Plus.
0~9 : Numeric key.
/ : Division function.
＊ : Multiplication function.
－ : Subtraction function.
＋ : Addition function.
﹒ : A decimal point of dot.
＝ :To be equal to, The amount.
Page 43
ZEBEX INDUSTRIES INC.
Subject Version Date Page
Z-2065 series User’s Manual 3.00 2010/3/19 43 / 69
File Transfer
File Transfer is a simple file transferring function tool, the tool can transfer file
to another devices via blue tooth. Communication agreement of file
transferring was adopted with OBEX agreement which shared with cell phone
or Notebook PC. So you can simply use this function to transfer file to cell
phone or Notebook PC, or doing file transferring between two terminals.
File Transfer is capable to auto-search devices with Bluetooth communication,
so all devices within valid range will be listed in window of “1. Select Remote
Device.”
Function Instructions:
1. Select Remote Device
All devices with Bluetooth Communication functions are listed on the
display.
Query : For searching usable devices.
Stop : Stop searching.
Connect : For connecting with one device.
Disconnect : For disconnecting with current devices.
2. Select Transfer File
Select file need to be transferred, press bottom for selecting file.
Start Transfer : Start transferring file to targeted devices.
Page 44
ZEBEX INDUSTRIES INC.
Subject Version Date Page
Z-2065 series User’s Manual 3.00 2010/3/19 44 / 69
Ex. File Transferred Operation By Using Bluetooth
1. File Transferring by using Bluetooth:
Make sure Bluetooth devices was activated, Bluetooth Communication devices
can be activated under Switch Function within PowerPack software utilities.
1.1 Select “Query “ for searching Bluetooth devices, below window will
pop up on display.
1.2 Select Bluetooth devices for receiving file, select “ Connect ” for
connecting with devices, or select “ Disconnect ” to disconnect with
current devices.
Page 45
ZEBEX INDUSTRIES INC.
Subject Version Date Page
Z-2065 series User’s Manual 3.00 2010/3/19 45 / 69
1.3 Click ” … ” bottom to select the file need to be transferred, then click ”
OK ” bottom to confirm.
1.4 Select “ Start Transfer ” bottom to start file transferring.
Page 46
ZEBEX INDUSTRIES INC.
Subject Version Date Page
Z-2065 series User’s Manual 3.00 2010/3/19 46 / 69
Preload Manager
The Preload Manager is an auto execution program for ZEBEX’s WinCE
device. You may set programs into the Preload list box and running the
program by automatically or manually.
1. Modify Window located on top of display, providing functionalities of Priority,
Remove and Browse.
2. Priority : Providing “UP ”and “DOWN ” two bottoms for adjusting priority on
the lists.
1. Edit : Providing ”Remove “ 與 “Browse..” two functionalities，below are
instructions:
Remove：Deleting selected functionalities.
Browse.：Selecting program for preloading, files can be selected from
window by clicking Browse bottoms.
Page 47
ZEBEX INDUSTRIES INC.
Subject Version Date Page
Z-2065 series User’s Manual 3.00 2010/3/19 47 / 69
Preload Operation
1. Selected Program:
1.1 By clicking ”Browse..”，Below menu will appear, select preload
program by using folder. Programs can be selected more than once.
Confirming file by clicking “OK” will get back to Preload Manager main
page. Then complete its process.
Page 48
ZEBEX INDUSTRIES INC.
Subject Version Date Page
Z-2065 series User’s Manual 3.00 2010/3/19 48 / 69
2. Reset preload priority:
If the preload priority need to be set up as below：
(1)play music -> (2)open explorer -> (3)check everything
Follow steps listed below :
2.1 Select by clicking play music.exe program and click” Up ” bottom,
Therefore, play music.exe will be shifted up.
2.2 Then select by clicking check everything program and click
“Down” bottom. Therefore, check everything program will be shifted
down.
Page 49
ZEBEX INDUSTRIES INC.
Subject Version Date Page
Z-2065 series User’s Manual 3.00 2010/3/19 49 / 69
3. Remove a program:
In order to remove “open explorer” program, select by clicking program,
then select “Remove” by clicking on bottom to finish command.
Page 50
ZEBEX INDUSTRIES INC.
Subject Version Date Page
Z-2065 series User’s Manual 3.00 2010/3/19 50 / 69
Switch
The WiFi & Bluetooth switch utility. This application provides as a switch
function to let you easy turn on or off the function and power for WiFi and
Bluetooth interface. Window for setting up Wifi will pop up by double-clicking
small icon within red circle which shown as below diagram.
Under the content of “Profile”, the available wireless network access point will
be searching by clicking “ ” button. You can select an access point and
press “ ” button to connect with that network.
Page 51
ZEBEX INDUSTRIES INC.
Subject Version Date Page
Z-2065 series User’s Manual 3.00 2010/3/19 51 / 69
Existing access point can also be selected from Edit Profile shown as below
diagram.
Under content of main menu, existing profile (WiFi) can be set up as Auto Profile.
Existing Profile lists can be viewed existing profile by clicking “ ” button,
check profile and click on “ ” button. Select “On” from Auto Profile
menu to complete Auto Profile setting.
Page 52
ZEBEX INDUSTRIES INC.
Subject Version Date Page
Z-2065 series User’s Manual 3.00 2010/3/19 52 / 69
TrayScan
The TrayScan program is a barcode reader set up program, it offer you an
easy way to enable or disable the barcode scanner, and also offer you to set
up each barcode symbolic properties.
.
Below are instructions of functions on main page:
1. Output Mode
Providing three output methods such as Copy & Paste / Key Emulation /
None (Copy to Clipboard).
Page 53
ZEBEX INDUSTRIES INC.
Subject Version Date Page
Z-2065 series User’s Manual 3.00 2010/3/19 53 / 69
1.1 Copy & Paste
Copy and paste the barcode information into application that need to
execute data as input. (ex. WordPad)，
1.2 Key Emulation
Transfer barcode information via Key Emulation to executed
software’s edit window. Key Emulation function can also be used for
barcode scanning under conditions of Terminal Emulation, Command
Promp and some other program without touch panel. Read data will be
transferred to application program.
1.3 None(copy to clipboard)
Function provide required barcode information to application program,
after this function was activated, scanner will read barcode information
and save data into clipboard.
2. Terminal Character
Set the terminator control code with barcode data. We offer “Enter”,
“Space”, “Tab”, and “None” for selections. Terminator control code will be
sent every time when barcode was read.
3.
Suffix
Set the suffix character with barcode data.
4. Prefix
Set the preamble character with barcode data.
5. Setting
To set the barcode parameter value of each kind of barcode for barcode
scanner. Press the" Setting " button in TrayScan application to start the
barcode setting.
Page 54
ZEBEX INDUSTRIES INC.
Subject Version Date Page
Z-2065 series User’s Manual 3.00 2010/3/19 54 / 69
To check the barcode type selection for enable the type of barcode for read.
Press " " button to setting the barcode parameter value of each kind of
barcode.
Press " "button to use system default value to set up the
barcode parameter. The default value was show in below pictures.
Page 55
ZEBEX INDUSTRIES INC.
Subject Version Date Page
Z-2065 series User’s Manual 3.00 2010/3/19 55 / 69
The default values of EAN/UPC code and Code39.
The default values of ITF 2 of 5 code and Code128.
Page 56
ZEBEX INDUSTRIES INC.
Subject Version Date Page
Z-2065 series User’s Manual 3.00 2010/3/19 56 / 69
Backup/Restore
You can find this application is located on path “\settings\control Panel\”.
This application provides you an easy way to backup or restore the device
setting information into Flash Disk and storage card. Application also provides
selection of Flash Disk when there is no storage card. When Mini SD Card
was installed into devices, program will auto-search and provides selection of
SD Card from menu.
Page 57
ZEBEX INDUSTRIES INC.
Subject Version Date Page
Z-2065 series User’s Manual 3.00 2010/3/19 57 / 69
Backup : Select backup data as saved devices, press ” Backup ” bottom to
proceed backup. Display will restore when backup was finished.
Page 58
ZEBEX INDUSTRIES INC.
Subject Version Date Page
Z-2065 series User’s Manual 3.00 2010/3/19 58 / 69
Firmware Information
This application will check and display the version information of the device’s
operation system and PowerPack utility.
You can find this application is located on path " \settings\control Panel\".
This information is good for identify device firmware version for future update
or maintenance.
Page 59
ZEBEX INDUSTRIES INC.
Subject Version Date Page
Z-2065 series User’s Manual 3.00 2010/3/19 59 / 69
Function Key Manager
This application utility is provides you an easier way to set up function key for
your device. Through using this function key set up utility you will easily and
quickly to start the application program like, Window Media Player,
Calculator… etc, or your own designed application program, and even the
windows system function, like increasing or decreasing the volume or doing
the adjustment of brightness on LCD panel.
You can find this application is located on path “\settings\control Panel\”.
Program provides eight different function key (F1~F8) for set up, default
setting was shown as below:
F1: SIP ON/OFF。
F2: Backlight Manager。
F3: Power Switch。
F4: Calculator.exe。
F5: Volume + 。
F6: Volume -。
F7: Backlight +。
F8: Backlight -。
Page 60
ZEBEX INDUSTRIES INC.
Subject Version Date Page
Z-2065 series User’s Manual 3.00 2010/3/19 60 / 69
Function Key Manager Set Up Instruction:
Enable/ Disable : Enable or Disable Function Key
Provide two set up methods of Internal Function and Program File
Internal Function : Provide following options,
SIP ON/OFF
Backlight Manager
Power Switch
Stylus Calibration
Wi-Fi ON/OFF
Bluetooth ON/OFF
Volume +
Volume –
Backlight +
Backlight –
Cut
Copy
Paste
Program File : Install application program according to demand,
this function can be used for setting up auto-execution.
Page 61
ZEBEX INDUSTRIES INC.
Subject Version Date Page
Z-2065 series User’s Manual 3.00 2010/3/19 61 / 69
1. Edit Internal Function items：
1.1 Select items need to be modified, select by clicking ” Edit ” bottom to
enter set up window as below:
1.2 Select new functional item and complete editing.
Page 62
ZEBEX INDUSTRIES INC.
Subject Version Date Page
Z-2065 series User’s Manual 3.00 2010/3/19 62 / 69
2. Edit application software for auto-execution：
2.1 Select Program File item，then click ” Browse ” bottom to enter File
Opening Window.
2.2 Select software required auto-execution, then select ” OK ” bottom to
complete selecting process.
Page 63
ZEBEX INDUSTRIES INC.
Subject Version Date Page
Z-2065 series User’s Manual 3.00 2010/3/19 63 / 69
2.3 Confirmed Function / Program had been updated within column. Select
by clicking ” OK “ bottom to complete editing process. When Function
Key Manager Main Page reappear on the display, F1 on function key
item lists had been updated to testkeypadChar.
Page 64
ZEBEX INDUSTRIES INC.
Subject Version Date Page
Z-2065 series User’s Manual 3.00 2010/3/19 64 / 69
How to order
Please offer Part Number or Model Name for next purchase.
1. Z-2065 Series Windows CE.NET Handheld Computer Set.
Part Number Model Name Description
882-65W100-100
Z-2065WL1
WindowsCE.NET Handheld Computer, W/Wireless
LAN/BT module/1D engine/RS-232 DB9(F) cable / USB
interface
882-65W200-100
Z-2065WL2
WindowsCE.NET Handheld Computer, W/Wireless
LAN/BT module/2D imager/RS-232 DB9(F) cable / USB
interface
882-65W1GS-100
Z-2065W1GS
WindowsCE.NET Handheld Computer, W/Wireless
LAN/BT/GPRS/GPS module/1D engine/RS-232 DB9(F)
cable / USB interface
882-65W2GS-100
Z-2065W2GS
WindowsCE.NET Handheld Computer, W/Wireless
LAN/BT/GPRS/GPS module/2D imager/RS-232 DB9(F)
cable / USB interface
882-65G1SH-100
Z-2065W1GSH
WindowsCE.NET Handheld Computer, W/Wireless
LAN/BT/GPRS/GPS module/1D engine/RFID(H)/RS-232
DB9(F) cable / USB interface
882-65G2SH-100
Z-2065W2GSH
WindowsCE.NET Handheld Computer, W/Wireless
LAN/BT/GPRS/GPS module/2D imager/RFID(H)/RS-232
DB9(F) cable / USB interface
882-65W1G0-100
Z-2065W1G
WindowsCE.NET Handheld Computer, W/Wireless
LAN/BT/GPRS module/1D engine/RS-232 DB9(F) cable /
USB interface
882-65W2G0-100
Z-2065W2G
WindowsCE.NET Handheld Computer, W/Wireless
LAN/BT/GPRS module/2D imager/RS-232 DB9(F) cable /
USB interface
882-65W1S0-100
Z-2065W1S
WindowsCE.NET Handheld Computer, W/Wireless
LAN/BT/GPS module/1D engine/RS-232 DB9(F) cable /
USB interface
882-65W2S0-100
Z-2065W2S
WindowsCE.NET Handheld Computer, W/Wireless
LAN/BT/GPS module/2D imager/RS-232 DB9(F) cable /
USB interface
882-65W1H0-100
Z-2065W1H
WindowsCE.NET Handheld Computer, W/Wireless
LAN/BT module/1D engine/RFID(H)/RS-232 DB9(F)
cable / USB interface
882-65W2H0-100
Z-2065W2H
WindowsCE.NET Handheld Computer, W/Wireless
LAN/BT module/2D imager/RFID(H)/RS-232 DB9(F)
cable / USB interface
Standard Accessories
170-70R449-180 RS-232 Cable RS232 charging cable for Z-2050/2065
173-0U0000-150 MINI USB Cable Terminal to PC USB port
862-206502-400 Battery Pack
Lithium-Ion rechargeable battery pack, 3.7V 5000 mAh
Page 65
ZEBEX INDUSTRIES INC.
Subject Version Date Page
Z-2065 series User’s Manual 3.00 2010/3/19 65 / 69
560-820500-741 Stylus Pen Length: 95.7cm, including reset thimble
623-220500-061
Sling Sling for stylus pen
623-220650-051 Hand Strip Z-2065 hand strip and stylus pen holder
560-020650-891 Hand Strip Holder Z-2065 hand strip holder
11S-900180-008 AC Adapter AC 100~240V 50/60HZ 0.6A, DC 9V/2A
11S-000000-008 Integrated Plug head for 11S-900180-008 Type: Britain/ U.S./Australia/Europe
Page 66
ZEBEX INDUSTRIES INC.
Subject Version Date Page
Z-2065 series User’s Manual 3.00 2010/3/19 66 / 69
2. CRD-60 Communication and Battery charging Cradle Set.
Part Number Model Name
Description
882-60CR00-000
CRD-60
Z-2065 communication and battery
charging cradle
Standard Accessories
174-1RF050-150
RS-232 Cable
RS232 cable connect from CRD-60 to PC
RS-232 Dsub port.
173-0U3000-150
USB Cable
RJ45 USB type B cable connect from
CRD-60 to PC USB port.
PIN-OUT configuration
DB-9(F)
1 CD (Carrier detect)
2 TxD (Transmit data)
3 RxD (Receive data)
4 DSR (Data set ready)
5 GND (Signal ground)
6 DTR(Data terminal ready)
7 CTS (Clear to send)
8 RTS (Request to send)
9 RI (Ring indicator)
PIN-OUT configuration
1 NC
2 TxD (Transmit data)
3 RxD (Receive data)
4 NC
5 GND (Signal ground)
6 NC
7 CTS (Clear to send)
8 RTS (Request to send)
9 NC
10 GND(Signal ground)
Page 67
ZEBEX INDUSTRIES INC.
Subject Version Date Page
Z-2065 series User’s Manual 3.00 2010/3/19 67 / 69
3. Z-2065 Series Optional Accessories
Part Number Model Name Description
170-70R449-180
RS-232 cable RS232 charging cable for Z-2050/2065
PIN-OUT configuration
DB-9 (Female)
1 CD (Carrier detect)
2 TxD (Transmit data)
3 RxD (Receive data)
4 DSR (Data set ready)
5 GND (Signal ground)
6 DTR (Data terminal ready)
7 CTS (Clear to send)
8 RTS (Request to send)
9 RI (Ring indicator)
173-0U0000-150
MINI USB Cable Terminal to PC USB port
174-1RF050-150
RS-232 Cable
RS-232 cable connect from CRD-60 to PC
RS-232 Dsub port.
173-0U3000-150
USB Cable
RJ45 USB type B cable connect from
CRD-60 to PC USB port.
862-206502-400
Battery Pack
Lithium-ion rechargeable battery pack,
3.7V, 5000mAh
560-820500-741
Stylus Pen 95.7mm, including reset thimble
Page 68
ZEBEX INDUSTRIES INC.
Subject Version Date Page
Z-2065 series User’s Manual 3.00 2010/3/19 68 / 69
Part Number Model Name Description
623-220500-061 Sling Sling for stylus pen
623-220650-051 Hand Strip
Z-2065 hand strip and stylus pen
holder
560-020650-891 Hand Strip Holder Z-2065 hand strip holder
862-206502-400 AC Adapter
AC 100~240V 50/60HZ 0.6A, DC
9V/2A
11S-000000-008
Adapter Head
Britain type head ,interchangeable
plug, for 11S-900180-008 AC adapter
11S-000001-008 Adapter Head
U.S. type head ,interchangeable plug,
for 11S-900180-008 AC adapter
11S-000002-008 Adapter Head
Australia type head ,interchangeable
plug, for 11S-900180-008 AC adapter
11S-000003-008 Adapter Head
Europe type head ,interchangeable
plug, for 11S-900180-008 AC adapter
Page 69
ZEBEX INDUSTRIES INC.
Subject Version Date Page
Z-2065 series User’s Manual 3.00 2010/3/19 69 / 69
<< MEMO >>
Loading...