查询V330ME04供应商
9939 Via Pasar • San Diego, CA 92126
TEL (858) 621-2700 FAX (858) 621-2722
V621ME23
VOLTAGE CONTROLLED OSCILLATOR
A1Rev
PHASE NOISE (1 Hz BW, typical)
-70
-80
-90
-100
FEATURES
• Tuning Voltage:
•
MINI-16-L
- Style Package
1710
-
1980
1 - 18 Vdc
MHz• Frequency Range:
APPLICATIONS
•
Earthstations
•
Satellite Modems
Handheld Phones
•
PERFORMANCE SPECIFICATIONS
Oscillation Frequency Range
Phase Noise @ 10 kHz offset (1 Hz BW, typ.)
Harmonic Suppression (2nd, typ.)
Tuning Voltage
Tuning Sensitivity (avg.)
Power Output
Load Impedance
Input Capacitance (max.)
Pushing
Pulling (14 dB Return Loss, Any Phase)
Operating Temperature Range
Package Style
-110
-120
£(f) (dBc/Hz)
-130
-140
1 E+3 10 E+3 100 E+3
OFFSET (Hz)
VALUE UNITS
-
1710 1980
-110
-15
1 - 18
20
3±3
50
50
<5
<1
-40 to 85
MINI-16-L
MHz
dBc/Hz
dBc
Vdc
MHz/V
dBm
pF
MHz/V
MHz
°C
POWER SUPPLY REQUIREMENTS
Supply Voltage (Vcc, nom.)
Supply Current (Icc, typ.)
All specifications are typical unless otherwise noted and subject to change without notice.
APPLICATION NOTES
• AN-100/1 : Mounting and Grounding of VCOs
• AN-102 : Proper Output Loading of VCOs
• AN-107 : How to Solder Z-COMM VCOs
NOTES:
© Z-Communications, Inc.
Page 1
22
5
Vdc
mA
All rights reserved
LOW COST - HIGH PERFORMANCE
VOLTAGE CONTROLLED OSCILLATOR
2100
2050
2000
1950
1900
1850
1800
1750
1700
FREQUENCY (MHz)
1650
1600
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
TUNING VOLTAGE (Vdc)
POWER CURVE, typ.
TUNING CURVE, typ.
V621ME23
PAGE 2
85
°c
°c
25
-40
°c
5
4
3
2
1
POWER OUTPUT (dBm)
0
1653 1699 1734 1769 1806 1848 1895 1944 1982 2007
FREQUENCY (MHz)
PHYSICAL DIMENSIONS
MINI-16-L
415-0061 REV. D
(DRAWING NO T TO SCALE)
0.115
0.000
0.500
0.475
0.405
0.305
0.205
0.105
0.025
0.000
P2=RF OUT
P3=Vcc
BOTTOM VIEW
0.025
0.085
GROUND PLANE SOLDER PLATED
P1=VT
0.185
TYPICAL OF ALL PADS
.070
.037
.052
.150
TYP
.114
0.220
0.320
0.420
0.475
0.500
P2
P1
0.285
0.415
0.315
P3
0.215
0.115
0.500
0.385
DETAIL A
SEE DETAIL 'A'
TABS RANGE:
SEE NOTE 5.
(4 PLACES)
.130
.034
0.000
-.005
SEE NOTE 3
NOTES:
THE INSIDE RADIUS OF ALL 16 HALF HO LE S
.031
.026
.465
1.
AT THE PERIMETER OF THE BOARD ARE
PLATED TO PROVIDE A SURFACE FOR THE
ATTACHMENT OF THE VCO TO A PCB,
IN 13 LOCATIONS, WITH 3 PADS BEING
USED FOR ELECTROMECHANICAL INTERFACE.
16 SOLDER LOCATIONS REQUIRED.
2. THE SURFACE OF THE SHIELD IS TIN PLATED
AND MAY BE SOLDERED TO. THE SHIELD'S
BASE METAL IS COLD ROLLED STEEL.
3. THE GROUND PLANE IS GROUND AND ATTACHES
TO A GROUND TRACK ON THE UPPER SIDE OF
THE BOARD AS WELL AS THE SHIELD BY PTH.
4. UNLESS OTHERWISE NOTED ALL DIMENSIONS
ARE IN INCHES.
5. UNLESS OTHERWISE NOTED ALL TOLERANCES
ARE AS FOLLOWS:
TOLERANCES
.XXX= ± .010
.070 TYP
25
°c
© Z-Communications, Inc.
Page 2
Printed in the U.S.A.
Loading...