This user’s manual and the software described in it are copyrighted with all rights reserved. No part of
this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated
into any language in any form by any means without the written permission of Z-Com Corporation.
About This Manual
This manual explains Z-Com outdoor ZMAX-8210 Customer Premise Equipment (CPE), how to build
the infrastructure centered on the ZMAX-8210 and proposals when using this CPE.
Note:
This indicates an important Note.
Cautions are given to prevent any damage to the ZMAX-8210, data lose or
Bold: Indicates the function, important words, and so on.
Thank you for choosing the ZMAX-8210 Series Customer Premise Equipment (hereafter called CPE).
Compliant with the innovative IEEE802.16-2004 and working at the licensed 3.5GHz with efficient
modulation, this outdoor CPE gives wireless ISP providers today’s fastest pathway to new markets and
revenue. whether well-established and looking to expand, or smaller and newly established – service
providers of all types can immediately and cost-effectively create wireless networks even in most
challenging environments or reach out from established network to capture new customers. Without the
delays and costs of leasing or building a wired infrastructure, ZMAX-8210 is capable of providing
secure and reliable access to high-speed data, voice and video services. ZMAX-8210-I build in 16dBi
gain antenna, ZMAX-8210-E with N-Female connector for external antenna. Typically, 802.11 s Mesh
implemented in this device will free physical limitation that a block stands in the way in the
infrastructure could lead to failure of communication), finding a key to “the last mile”.
Appearance
Figure 1 ZMAX-8210
Chapter 1
Introduction
- 1 -
Figure 2 ZMAX-8210 ports
The ZMAX-8210 appearance is designed to be water-proof and dust-proof for most challenging
environments outdoors.
Key Features
The ZMAX-8210 provides you with the solid features. Power supply via POE Based on WiMAX together with compliant with 802.16d-2004 Work at 3.5GHz Implement Orthogonal Frequency Division Multiplexing (OFDM) and Non-Line-of-Sight (NLOS)
Efficient Modulation Water, dust-proof and built-in antenna for outdoor environments User-friendly web-based management
Build Typical Infrastructure
The versatile ZMAX-8210 greatly livens up the internet for your various needs. Typically Point-to-Point,
Point-to-Multipoint modes are mostly recommended infrastructures.
Wireless Point-to-Point Outdoors
Chapter 1
Introduction - 2 -
Figure 3 Wireless Point-to-Point Outdoors
Under this structure, the ZMAX-8210 acts as a customer premise equipment (CPE), connecting a
WiMAX Base Station.
Wireless Point-to-multipoint Outdoors
Under this structure, acting as a customer premise equipment, the ZMAX-8210 is connected to the
WiMAX Base Station, allowing ISP to cost-effectively build infrastructure in a matter of hours.
Chapter 1
Introduction - 3 -
Figure 4 Wireless Point-to-multipoint Outdoors
Typical Case
The high-quality performance enables the ZMAX-8210 to gain widespread acknowledgements. It is able
to undertake tasks in various situations.
Create or expand well-created network via this CPE in enterprises or residential quarters Provide an access to Metropolitan Area Network via WLAN Act as a media connecting Base Station and sub-stations in mobile communicating network Provide an access to hard-to-reach areas, like ancient sites Cost-effectively build in most challenging environments, like remote mountain areas and rough
sites via this CPE
Build a makeshift network for a meeting Link Backup or Emergency Communication
Chapter 1
Introduction - 4 -
Chapter 2 Basic Installation
System Requirement
Before installing the ZMAX-8210 Customer Premise Equipment, make sure your system meets these
requirements
A PC coupled with 10/ 100Base-TX adapter Configure the computer with a static IP address of 192.168.1.x (x cannot be 1) and 255.255.255.0
for the Subnet Mask
A Web browser for configuration such as Microsoft Internet Explorer 6.0 or above, or Netscape
Navigator 4.78 or above or Firefox
Package Content
If any missing or damaged, please contact your local seller.
Z-Com ZMAX-8210 Customer Premise Equipment Power adapter and cord (48V,1A) Accessories (For its full contents, please refer to accessory installation guide) ZMAX-8210 Customer Premise Equipment Installation Guide
Hardware Installation
Follow the steps below to install your ZMAX-8210. (the different of hardware installation between
ZMAX-8210-I and ZMAX-8210-E is antenna)
Make sure all components linked to the ZMAX-8210 are on hand.
A brace fixed on the back of the ZMAX-8210 is tabled on a perfect area like well-sized desk. Attach one end of water-proof cable to a water-proof connector. Alternatively, you can make a
Category 5 UTP straight yourself.
Chapter 2
Introduction - 5 -
g
Connect the other end of the Ethernet cable to the ZMAX-8210.
Tighten the water-proof connector.
A ground wire connects the ZMAX-8210.
Ground
Note:
To keep the ZMAX-8210 antenna intact, a plastic coat is over the antenna. Remove
the coat wile using it.
Warnin
Chapter 2
:
Introduction - 6 -
g
Be sure to your ZMAX-8210 is connected the ground wire, preventing something
unexpected.
Antenna Installation
16dBi built-in antenna is placed in the ZMAX-8210, so you need not install antenna.
The ZMAX-8210-E needs an external antenna. You should choose your antenna as your need.
Warnin
Keep your ZMAX-8210 associated with the antenna away from power line, lamp,
electrified wire fence or anything others electrified.
Though a thunder-proof component is built in, it is recommended that additional
thunder-proof device is needed for ef fect iv ely protec ti ng y our ZMAX - 82 10.
:
Chapter 2
Introduction - 7 -
Chapter 3 Basic Settings
Default Factory Settings
We’ll elaborate the ZMAX-8210 default factory settings. You can re-acquire these parameters by resort
button. If necessary, please refer to the “the way to restore default factory settings.
Table 1 ZMAX-8210 Default Factory Settings
Feature Factory Default Settings
User Name admin
Password password
Device Name
Spanning Tree Protocol Enable
IP Settings
HTTP Redirect Disable
Wireless Settings
Devicexxxxxx(xxxxxx represents the last 6 digits of
MAC address)
IP Type:STATIC
IP Address:192.168.1.1
Subnet Mask:255.255.255.0
Default Gateway:0.0.0.0
Primary/Second DNS Server:0.0.0.0
Base Station ID:01020304050D
Dual-Direction Voice:TDD
Bandwidth:7MHz
Encryption:Disable
IR Bit: 0
SSH Disable
SNMP:Enable
Trap Server:192.168.0.254
SNMP
Read Community:public
Write Community:private
How to Login Your ZMAX-8210 via WEB Browser
ZMAX -8210 provides you with user-friendly web-based management. Take the following steps
Enter the ZMAX-8210 via IE. When entering the IP address: http://192.168.1.1, you’ll see a popup
menu below:
Chapter 3
Basic Settings
- 8 -
Clicking “Yes” ushers you into the login.
Figure 5 Safety Alert
Figure 6 Login
Note:
Make sure the PC IP address need to be matched the device. For instance, the
ZMAX-8210 is 192.168.1.1, and your PC IP should be 192.168.1. X.
Enter the default name “admin” in the username field and “password” in the password field。Clicking “ Login now ” will usher you into the ZMAX-8210 management interface.
Chapter 3
Basic Settings - 9 -
Loading...
+ 34 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.