Z Com ZCN1523H28V4, ZCN1523H28V04 Users Manual

802.11n 2.4G WLAN
Customer Premises Equipment

Quick Installation Guide

V1.0 August 2009

Copyright

Copyright © 2009 all rights reserved. No part of this publication may be reproduced, adapted,
stored in a retrieval system, translated into any language, or transmitted in any form or by any
means without the written permission of the supplier.

About the Quick Installation Guide

This Quick Installation Guide is intended to guide professional installer to install the
IEEE802.11n

problems.

Wireless CPE. It covers procedures to assist you in avoiding unforeseen

Conventions

Warning:

This sign indicates a warning or caution that you have to abide.

Note:

This sign indicates an important note that you must pay attention to.

FCC Information

This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2)
this device must accept any interference received; including interference that may
cause undesired operation.

Federal Communications Commission (FCC) Statement
This Equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help.

Warning: Any changes or modifications to this unit not expressly approved by
the party responsible for compliance could void the user authority to operate
the equipment.

Trade name
Model number

FCC RF Radiation Exposure Statement:

1. This Transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.

2. This equipment complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with a
minimum distance of 20 centimeters between the radiator and your body.

For product available in the USA market, only channel 1~11 can be operated.
Selection of other channels is not possible.

CE Statement:
Hereby, Z-COM,Inc. declares that this device is in compliance with the

essential requirements and other relevant provisions of the R&TTE Directive

1999/5/EC.

This device will be sold in the following EEA countries: Austria, Italy, Belgium,
Liechtenstein, Denmark, Luxembourg, Finland, Netherlands, France, Norway,
Germany, Portugal, Greece, Spain, Iceland, Sweden, Ireland, United Kingdom,
Cyprus, Czech Republic, Estonia, Hungary, Latvia, Lithuania, Malta, Slovakia,
Poland, Slovenia, Bulgaria, Romania.

Chapter 1 Introduction

Introduction

The IEEE802.11n Wireless CPE is a multi-mode last-mile broadband solution for
customers like wireless ISP (WISPs) and system integrators. By the nature of complying with
the IEEE802.11n standard and featuring high power output, IEEE802.1
supports higher bandwidth with lon ger range for outdoor applications.

IEEE802.11n
premises equipment (CPE). While being as the access point, it can be deployed outdoors to
provide outdoor wireless internet service. In the other way to be as the outdoor CPE, it can
receive wireless signal over the last mile, helping WISPs deliver internet service to the new
residential and the business customer where wired broadband internet service, such as cable
and DSL, can not serve in. In addition, the easy-to-install IEEE802.1
covers 2.4GHz bands, which features outstanding throughput performance and a
cost-effective design that allows users to have the reli able outdoor equipment at the affordable
price.

Wireless CPE can be used as the access point or the customer

1n Wireless CPE

1n Wireless CPE

Chapter 1 Introduction Page 5

Chapter 2 Preparation before Installation

This chapter describes safety precautions and product information you have to know. Please
check this chapter before installing the IEEE802.1

1n Wireless CPE.

Professional Installation Required

1. Please seek assistance from a professional installer who is well trained in the RF
installation and knowledgeable in the local regulation s.

2. The IEEE802.1
installers with professional technicians and will not be sold directly through retail stores.

1n Wireless CPE is distributed through distributors and system

Safety Precautions

To keep you safe and install the hardware properly, please read and follow these safety
precautions.

1. If you are installing the IEEE802.11
as well as others’, please seek assistance from a professional installer who has
received safety training on the hazards involved.

2. Keep safety as well as performance in mind when selecting your installation site,
especially where there are electric power and phone lines.

3. When installing the IEEE802.11

♦ Do not use a metal ladder;
♦ Do not work on a wet or windy day;
♦ Wear shoes with rubber soles and heels, rubb er gloves, long sleeved shirt or jacket.

4. When the system is operational, avoid standing directly in front of it. Strong RF fields are
present when the transmitter is on.

n Wireless CPE for the first time, for your safety

n Wireless CPE, please note the following things:

Chapter 2 Preparation before Installation Page 6

Installation Precautions

To keep the IEEE802.11n Wireless CPE well while you are installing it, please read and
follow these installation precautions.

1. Users MUST use a proper and well-installed surge arrestor and grounding kit with

IEEE802.11n
fatal damage to IEEE802.1

NOT COVERED UNDER WARRNTY.

2. Users MUST use the “Power cord & PoE Injector” shipped in the box with the IEEE802.11n

Wireless CPE. Use of other options will cause damage to the IEEE802.11n Wireless
CPE.

3. Users MUST power off the IEEE802.11n

external antenna to it; otherwise, damage might be caused to the IEEE802.1
CPE itself.

Wireless CPE; otherwise, a random lightening could easily cause

1n Wireless CPE. EMD (Lightning) DAMAGE IS

Wireless CPE first before connecting the

1n Wireless

Product Package

The product package you have received should contain the following items. If any of them are
not included or damaged, please contact your local vendor for support.

IEEE802.11n Wireless CPE ×1
Pole Mounting Ring ×1
Power cord & PoE Injector ×1
Quick Installation Guide ×1
Product CD ×1

Note:

Product CD contains Quick Installation Guide and User Manual!

Chapter 2 Preparation before Installation Page 7