1
802.11g SOHO
Wir eless Access Point
XG-1020
User’s Manual
Version 1.0 – Novenmber 2006
2
Table of Content
Chapter 1 Introduction.............. ............................................................ ........................... 3
1-1 Features and Benefits........................................ ..... ... .. ..... .. ... ..... .. .. ..... ... .... ... .. ..... .. ... 3
1-2 Applications.............................................................................................................. 4
Chapter 2 Hardware Installation.................................. ............................. ...................... 5
2-1 Package Contents....................................................................................... ............... 5
2-2 System Requirements............................................................................................... 5
2-3 Mechanical Description............................................ ................................................ 6
2-4 Hardware Installation ............. .................................................................................. 8
2-5 Safety Notification............. .................................. ..................................................... 9
Chapter 3 Configuring your Access Point with the Web-Based User Interface ..........10
3-1 Start-up and Log in..................................................................................................10
3-1-1 Status.................................................................. ..................................................10
3-1-2 System................................................................... ...............................................11
3-2 Wireless Setup.........................................................................................................12
3-2-1 Wireless Settings......................................... ......................................................... 12
3-2-1-1 AP Mode ...........................................................................................................12
3-2-1-2 Wireless Client..................................................................................................16
3-2-1-3 Bridge ......................................................... ......................................................18
3-2-1-4 AP+Repeater.......................................................... ................................ ...........21
3-2-2 Security Settings............... .................................. ................................ ..................25
3-2-3 MAC Filter................................................................................. ..........................28
3-3 Management..................................... ............................... ............................... .........29
3-3-1 Password Setup ........................ ............................................................................29
3-3-2 Configuration File................................................................................................30
3-3-3 F/W Upload. ............................... ............................................................ ..............31
3-3-4 Event Log......................................................... ....................................................32
Limited Warran ty............................................................................................................. 2
3
Chapter 1 Introduction
The 802.11g SOHO W ireless Access Point is an AP and Bridge Mode, 2.4GHz and up to 54Mbps
wireless LAN access point. The 802.11g SOHO Wireless Access Point can communicate with
other mobile devices enabled for 802.11g standard -based wireless LAN connectivity. Using the
card in conjunction with the 802.11g SOHO Wireless Access Point, you can create a wireless
network for sharing your broadband cable or DSL Internet access among multiple PCs in and
around your home or office and enjoy amazing speed of 54Mbps.
This high-speed wireless device simultaneously supports both IEEE 802.11b and 802.11g
wireless networks and lets you quickly network multiple PCs and notebooks without laying new
cables, and gives users the freedom to roam throughout the workplace and stay connected to
corporate resources, e-mail, and the Internet.
1-1 Features and Benefits
Technique operating in the unlicensed 2.4GHz ISM band.
Support Super-G and Turbo-G: increase the throughput performance.
Interoperable with IEEE 802.11g wireless devices.
Support AP, Wireless Client, Repeater and Bridge Mode.
Enhanced Security: WEP Encryption (64, 128 and 152-bit), 802.1x (EAP-TL S, E AP-TTLS,
LEAP, EAP-PEAP), WPA/ WPA-PSK, WP A2/WPA2-PSK, Wireless MAC MAC Filter List .
Interfaces directly to IEEE 802.3 (10/100-BaseTX RJ-45 LAN port) Fast Ethernet net works.
Supports 1, 2, 5.5, 11, 6, 9, 12, 18, 24, 36, 48, 54 and 108 Mbps (Turbo G / Super G) data
rates.
4
1-2 Applications
The 802.11g SOHO Wireless Access Point offers a fast, reliable, high-speed, and high security
solution for wireless clients access to the network in applications like these:
1. Remote access to corporate network information
E-mail, file transfer and terminal emulation.
2. Difficult-to-wire environments
Historical or old buildings, asbestos installations, and open area where wiring is difficult to
deploy.
3. Frequently changing environments
Retailers, manufacturers and those who frequently rearrange the workplace and change
location.
4. Te mporary LANs for special projects or peak time
♦ Trade shows, exhibitions and construction sites where a temporary network will be
practical.
♦ Retailers, airline and shipping companies need additional workstations during peak
period.
♦ Auditors requiring workgroups at customer sites.
5. Access to database for mobile workers
Doctors, nurses, retailers, accessing their database while being mobile in the hospital, retail
store or office campus.
6. High security connection
The secure wireless network can be installed quickly and provide flexibility.
5
Chapter 2 Hardware Installation
This chapter describes initial setup of the 802.11g SOHO Wireless Access Point.
2-1 Package Contents
The package you have received should contain the following items: If any of the above items are
not included or damaged, please contact your local vendor for support.
• 802.11g SOHO Wireless Access Point………..…………...…………..………..x1
• Dipole Antenna. ....…………………………………..…………………...……..x1
• Power Adapter…………………………………………………………….……x1
• Product CD….………………………………………………………….………x1
• Quick Installation Guide...………………..…………………………………….x1
2-2 System Requirements
Before installing the 802.11g SOHO Wireless Access Point, please make sure that these
requirements have been met:
A 10/100 Mbps Local Area Network device such as a hub or switch.
Category 5 networking cable.
An A/C power adapter (12V DC).
A Web browser for configuration: Microsoft IE 4.0 or above, or Netscape Navigator 4.5 or
later version.
Installing TCP/IP protocol to the computer.
6
2-3 Mechanical Description
Front Panel
The front panel provides LED’s for device status. Refer to the following table for the meaning of
each feature.
LED STATUS Description
Off 802.11g SOHO Wireless Access Point is off.
PWR/SYS
On 802.11g SOHO Wireless Access Point is in service.
Green Off No ethernet link is detected.
Green On 10Mbps Ethernet link is detected.
Green
Blinking
Data sending/receiving.
Amber On 100Mbps Ethernet link is detected.
ETHN
Amber
Blinking
Data sending/receiving.
Off Indicates no 802.11g wireless links.
On Wireless LAN is in service but no activity. WLAN
Blinking Indicates the device is linking or active data through wireless links.
EZ Button
The button to make user easy to setup wireless security.
註解 [NH1]: Front Panel
Picture
7
Rear Panel
To know the rear panel features, please refer to the following table for the meaning of each
feature.
Power
Socket
(DC 12v)
Connect the DV 12V/1.2A power supply. ONLY use the power adapter
supplied with the 802.11g SOHO Wireless Access Point. Otherwise, the
product may be damaged.
Reset
Simply press the reset button and keep pressing it for around 5 seconds.
The 802.11g SOHO Wireless Access Point will be restored to factory
default settings.
LAN
Use the Ethernet RJ-45 port to connect to the 10/100Mbps Ethernet
network and Ethernet through a device such as a hub, switch, or router.
ANT.
This is connector for anntena.
註解 [NH2]: Rear Panel Picture
8
2-4 Hardware Installation
Before installing the 802.11g SOHO Wireless Access Point, you should make sure that your
Ethernet network is up and working with a computer. You'll be connecting the access p oint to the
Ethernet network so that computers with 802.11g wireless adapters will be able to co mmunicate
with computers on the Ethernet network.
Please take the following steps to successfully to set up the Access Point.
Note: W e suggest you first install the 802.1 1g SOHO W i reless Access Point with default settings.
Site Selection
Before installation, it is very important to decide on the location of the 802.11g SOHO
Wireless Access Point. Proper placement of the 802.11g SOHO Wireless Access Point is
critical to ensure optimum radio range and performance. Typically, the best location to place
the 802.11g SOHO W ireless A ccess Point at your site is the center of your wireless coverage
area. Try to place your mobile stations within the line of sight. Obstructions may impede
performance of the 802.11g SOHO Wireless Access Point.
802.11g SOHO Wireless Access Point Placement
You can place the 802.11g SOHO Wireless Access Point on a flat surface such as a table or
cabinet, or mount the unit on a vertical surface like a wa ll. The integrated antenna of your
Access Point performs best in an open environment with as few obstructions as possible. In
most situations placing the 802.11g SOHO Wireless Access Point will provide satisfactory
performance results.
Note: We suggest you configure and verify the 802.11g SOHO Wireless Access Point
operations first before you are planning to mount the 802.11 g SOHO Wireless Access Point
on a wall or in a remote location.
Connect the Ethernet Cable
The 802.11g SOHO Wirele ss Access Point supports 10/100M Ethernet connection. Attach
your UTP Ethernet cable to the RJ-45 connector on the 802.11g SOHO Wireless Access
Point. Then connect the other end of the RJ-45 cable to a hub or a station.
9
Connect the Power Cable
Connect the power adapter to the power socket on the 802.11g SOHO W ireless Access Point,
and plug the other end of the power into an electrical outlet.
Warning: We cannot assume the responsibility for the damage from using with the other
power adapter supplier.
Configure the wireless device settings
To access the 802.11g SOHO Wireless Access Point, wireless device needs to configure the
802.11b or 802.11g Wireless Adapter to use the 802.11g SOHO Wireless Access Point
factory default settings as follows:
SSID: Wireless
Channel: 6
WEP: Disable
Verify wireless connectivity to the network
Using a computer with an 802.11b or 802.11g wireless adapter, browse internet or check file
access on the network. If everything is functioning properly, then you have successfully
installed the 802.11g SOHO Wireless Access Point.
2-5 Safety Notification
Your Wireless AP should be placed in a safe and secure location. To ensure proper operation,
please keep the unit away from water and other damaging elements.
Please read the user manual thoroughly before you install the device.
This device should only be repaired by authorized and qualified personnel.
Please do not try to open or repair the device yourself.
Do not place the device in a damp or humid location, i.e. a bathroom.
Please do not expose the device to direct sunlight or other heat sources. The housing and
electronic components may be damaged by direct sunlight or heat sources.
10
Chapter 3 Configuring your Access Point
with the Web-Based User Interface
3-1 Start-up and Log in
In order to configure the Acce ss Point, you must use your web browser and please do the
following:
1. Type this Access Point’s address http://192.168.1.1
in the Location (for IE) or Address field
and press Enter.
2. Enter the system password (the default setting is “password”).
3. Click on the “Login” button.
4. The main page will appear.
After you have logged-in the main page, the Status, System, Wireless Setup, AP Status,
Management buttons will be shown. The main menu provides links to the whole sections of the
web configuration interface.
3-1-1 Status
The Status screen describes the product information briefly. The device status includes Access
Point Information, IP settings, and Wireless settings.
11
3-1-2 System
The Device Name is used to give a name to your Access Point. This will enable you to manage
your Access Point more easily if you have multiple Access Points on your network.
IP Address Assigment: Allow you to setup your device ip address. You can use fixed IP address
or obtain IP address automatically.
Note: If you complete the settings, please click on “Apply” for changes to take effect.
12
3-2 Wireless Setup
3-2-1 Wireless Settings
The Wireless LAN Setup page lets you make changes t o the wireless network settings. The Basic
Settings, you can make changes to the wireless network name Operation Mode, SSID,
Broadcast SSID, Wi reless M ode, Channel/Frequency. The Advance Settings, you can make
changes to the other advance settings, such as Output Power, Data Rate etc.
Basic Settings
Operation Mode: Selecte the operating mode from the drop-down list. The options are Access
Point, Wireless Client, Bridge, AP+Repeater.
3-2-1-1 AP Mode
SSID: The SSID is a unique ID used by Access Points and Stations to identify a wireless LAN.
Wireless clients associating to any Access Point must have the same SSID. The default SSID is
“Wireless”. To change the SSID, type in the SSID you like to use. It is case sensitive and must not
exceed 32 characters.
Hide SSID: For security concern, you can choose not to broadcast your network’s SSID. To turn
off the broadcast of the SSID, click “No” check box next to “Broadcast SSID”. And your Access
Point will refuse the connection requests from whose are not a ware the Network ID. But certainly
the Access Point can be easily connected well when you realize the Network ID. The default
setting is “Yes”.
Loading...