R1 Extender
Quick Installation Guide
V1.0 January 2009
Copyright
Copyright © 2008 all rights reserved. No part of this publication may be reproduced, adapted,
stored in a retrieval system, translated into any language, or transmitted in any form or by any
means without the written permission of the supplier.
About the Installation Guide
This Installation Guide is intended to guide professional installer to install the R1 Extender. It
includes procedures to assist you in avoiding unforeseen problems.
Conventions
Warning:
This indicates a warning or caution that you have to abide.
Note:
This indicates an important note that you must pay attention to.
Chapter 1 Introduction
Introduction
The R1 Extender is a high-performance outdoor-deployable wireless bridge that provides
wireless connectivity among multiple network locations. It supports Base Station, CPE, PTP
and PTMP connectivity. Moreover, the R1 Extender has a built-in 23dBi planar antenna that
can deliver up to a 40Km connection. With high throughput and long-distance transmission,
the R1 Extender is an ideal backhaul solution for Carriers, Service Providers and Enterprises!
Chapter 1 Introduction Page 3
Chapter 2 Preparation before Installation
This chapter describes safety precautions and product information you have to know and
check before installing R1 Extender.
Professional Installation Required
1. Please seek assistance from a professional installer who is well trained in the RF
installation and knowledgeable in the local regulation s.
2. The R1 Extender is distributed through distributor and system installer with professional
technicians and will not be sold directly through retail store.
Safety Precautions
To keep you safe and install the hardware properly, please read and follow these safety
precautions.
1. If you are installing an antenna for the first time, for your safety as well as others’, please
seek assistance from a professional installer who has received safety training on the
hazards involved.
2. Keep safety as well as performance in mind when selecting your installation site,
especially where there are electric power and phone lines.
3. When installing your antenna, note the following:
♦ Do not use a metal ladder;
♦ Do not work on a wet or windy day;
♦ Wear shoes with rubber soles and heels, rubb er gloves, long sleeved shirt or jacket.
4. When the system is operational, avoid standing directly in front of the antenna. Strong RF
fields are present when the transmitter is on.
Chapter 2 Preparation before Installation Page 4
Product Package
The product package you have received should contain the following items. If any of them are
not included or damaged, please contact your local vendor for support.
R1 Extender with integrated 23dBi antenna ×1
Mounting Kit ×1
PoE Injector & Power cord ×1
Grounding Wire with Screw ×1
Water Proof RJ-45 Connector Kit ×1
Quick Installation Guide ×1
Product CD ×1
Note:
Product CD contains Management Tool, Quick Installation Guide and User
Manual!
Mounting Kit
Wall/Pole Mounting Bracket
1. T-Form Bracket ×1
2. Articulation Pole ×1
3. Pole Mount Bar ×1
Fasteners
4. M8×80 Screw ×2
M8×90 Screw ×1
5. M8 Washer ×3
6. M8 Spring Washer ×3
7. M8 Nut ×1
8. M5×16 Screw ×4
9. M5 Washer ×4
Chapter 2 Preparation before Installation Page 5
10. Wood Screw ×4 (for Wall Mount)
11. Wall/Gyprock Plug ×4 (for Wall Mount)
Waterproof RJ-45 Connector Kit
1. Gland ×1
2. Sealing Nut ×1
3. Sealing ×1
Chapter 2 Preparation before Installation Page 6
Chapter 3 System Installation
Assemble the Mounting Bracket
1. Place the main bracket into the seating and use a spanner to fasten the bracket to the R1
Extender with M5×16 screws ⑧ and M5 washers ⑨ provided in the hardware packets;
2. Assemble the main bracket by placing articulation pole ② to the T-form bracket ① via a
M8×90 ④ screw through the insertion axe and fix with the M8 washer ⑤ , spring
washer ⑥ and M8 nut⑦;
Chapter 3 System Installation Page 7
Pole Mounting
1. Install the main bracket and the pole mount bar ③ over the top of the pole by
securing the drill holes of the pole mount bar to the main bracket ones and insert two
M8×80 ④ screws, spring washers ⑥ and washers ⑤ through the drill holes and
main bracket;
2. Fasten two M8×80 screws ④ and washers ⑤ through the drill holes and main
bracket with a spanner;
3. Adjust the antenna for appropriate tilt / vertical orientation.
Chapter 3 System Installation Page 8
Connect Up
Before installing the Ethernet cable with a waterproof RJ-45 conne ctor, it is recommended that
the Cat-5 RJ-45 coaxial cable be used for the bridge to power injector connections.
1. To connect to the hole labeled
coin or a slotted screwdriver and then screw in the body of the gland and tighten.
2. Slide the sealing nut to the RJ-45 cable from its middle breach and then insert the sealing
into the cable.
Slide the Sealing Nut from its Breach
PoE+Data, open the black cover in advance by using a
3. Insert the RJ-45 connector and make sure that the locking tab snap s home.
R1 Extender RJ-45 Port
4. Screw the sealing on the gland and tighten.
Chapter 3 System Installation Page 9
Ground the wire
The R1 Extender is shipped with a grounding wire. The unit must be properly grounded to
protect against power surges. The grounding point can be found on the bottom of the unit. It is
supplied with an appropriate grounding lug for attachment to the ODU.
Power On
To power up the R1 Extender, follow the steps bellow:
1. Plug a user-supplied Cat-5 Ethernet cable from your wired LAN (or a computer) into the
power injector RJ-45 jack (
2. Plug a user-supplied Cat-5 Ethernet cable from the R1 Extender into the power injector
RJ-45 jack (
3. Connect the power module to the power injector and plug the AC cord into an AC power
receptacle.
4. After being powered on, the device will send out the beep sound lasting about 1.5
seconds, informing you that the R1 Extender powered up! Wait for about 60 seconds the
P+DATA OUT);
DATA IN);
system will be initialized and start working.
Chapter 3 System Installation Page 10
Warning:
Make sure PoE is correctly connected to the RJ-45 port on the R1 Extender
labeled PoE+Data. DO NOT connect to the port labeled “Warning!! No POE”,
otherwise the extender will be severely damaged!
Chapter 3 System Installation Page 11
Chapter 4 Configuration
Connect the R1 Extender to a Local Computer
If you are configuring the R1 Extender locally (without connecting its power injector to a wired
LAN), connect a PC to the power injector’s Ethernet port using a Category 5 Ethernet cable.
1. Assign a static IP address to your PC which is in the same network segment with the R1
Extender. As the default IP address of this unit is 192.168.1.1, you may choose from
192.168.1.2 to 192.168.1.254.
2. Test the link status between your PC and the R1 Extender. Start a command prompt and
execute a continuous ping command “ping 192.168.1. 1 –t”. If ping to the wirel ess bridge is
successful (as shown below), open Internet browser and enter the bridge’s IP address in
the address filed and press Enter.
Chapter 4 Configuration Page 12
R1 Extender’s still initializing
System ready
Note:
Considering convenient configuration, it is recommended to configure local
and remote R1 Extender respectively on two computers.
TTL time may vary depending on the operating sy stem.
Chapter 4 Configuration Page 13
How to Establish Wireless Bridge Mode
The R1 Extender supports four operating modes, which are Base Station, CPE, Peer-to-Peer
(CSMA) and Peer-to-Peer (TDMA). Normally, Wireless Bridge is the typical mode on this unit.
Here we will illustrate how to establish wireless bridge connectivity with R1 Extender.
Enter the user name (admin) and password (password) to login and make configurations.
Note:
Due to browser ’s security trusted sites, 192.168.1.1 might not able to be opened.
You may choose to continue to the website.
Open “Basic Setup” in “System”, set the IP address of two R1 Extenders in the same
network segment. e.g. local R1 Extender as 192.168.1.1 and remote R1 Extender as
Chapter 4 Configuration Page 14
192.168.1.2 and set the IP Subnet Mask on both as 255.255.255.0
Warning:
Each IP address is unique within a LAN, otherwise IP collision may occur!
Open “Radio” in “Wireless” and you will find the default operating mode is Peer-to-Peer
(CSMA). Select to use the Peer-to-Peer (CSMA) operating mode and keep the
Channel/Frequency and Bandwidth on both R1 Extenders identical. Click “
Apply” to
save settings.
Chapter 4 Configuration Page 15
Login the Web-based interface of remote R1 Extender, open “About” in “System” and
record the wireless MAC address of it.
Login the Web-based interface of local R1 Extender and open “Peer-to-Peer Setup” in
“
Wireless”, input the WLAN MAC address of the remote one to “Remote MAC Address
” field and click “Apply”;
1
Chapter 4 Configuration Page 16
Warning:
The MAC address on the housing of R1 Extender is the ETH MAC address;
therefore it can not be used in Peer-to-Peer links.
The IP address of your PC should be in the same network segment to the one
of bridges.
Use ping to check whether the link between the two R1 Extender is OK.
R1 Extender B R1 Extender A
To get a better wireless connectivity, antenna alignment is strongly recommended after
Chapter 4 Configuration Page 17
both R1 Extenders are installed long distance apart.
Login the Web-based interface of the local R1 Extender and open “
in “
Wireless”. Hit “Align Antenna” button, an antenna alignment tool will popup. Specify
the Target RSSI and click “
Start” to begin the antenna alignment.
Peer-to-Peer Setup”
Fix the local antenna and adjust the remote antenna elevation and horizontal direction.
During the adjustment, observe “
antenna when it reaches your expectation. Usually, RSSI between -60 and -70dBm
indicates rather good signal strength.
Adjust the local antenna after fixing the remote one. During the adjustment, observe
“
Current RSSI” in the remote R1 Extender. Fix the local antenna when it reaches your
expectation.
Congratulations! You have primarily completed configuration on R1 Extender and they can be
put into operation. For more advanced configurations, please refer to the User manual.
Current RSSI” in local R1 Extender. Fix the remote
Chapter 4 Configuration Page 18
Chapter 5 Troubleshooting
This chapter provides troubleshooting procedures for basic problems with the R1 Extender.
Q 1. What if my R1 Extender fails to connect to the remote one?
• Ethernet Link: Check the availability of power to the bridge by observing the LED
status on the power injector.
- Green: The R1 Extender is connecting to the backha ul network.
- Off: The R1 Extender disconnects from the wired network, check whether the power
cord and Ethernet cables to the network and bridge are correctly connected.
•
Basic Configurations: Mismatched basic settings among bridges are the most
common cause of connectivity fail. If the bridge does not associate with a remote
bridge, check whether options in each device are identical.
•
Security Settings: Remote bridges attempting to authenticate to your R1 Extender
must support the same security options configured in your bridge, such as WEP and
WP A (2)-PSK. If your bridge fails to associate with others, check whether the security
settings are the same as your bridge settings.
•
Antenna Alignment: If the methods above are all checked to be correct, you can
observe and verify antenna alignment with RSSI value.
Q 2. What if I would like to reset the unit to default settings?
You may restore factory default settings in “Backup/Restore Settings” from “Management”
Q 3. What if I would like to backup and restore my configuration settings?
You may do the backup by generating a configuration file or retrieve the settings you have
backed up previously in “
Backup/Restore Settings” from “Management”.
Chapter 6 Service Information Page 19
Chapter 6 Service Information
If you have any further trouble using the R2 Extender or you would like to require additional
support, you may visit our website at www.zcom.com.tw/rpc or you may contact us as below
for support:
Z-Com, Inc.
Taiwan
Business
Center
Zcomax Technologies, Inc.
California
Business
Center
New
Jersey
Business
Center
ZCOMAX - United Kingdom Limited
European
Business
Centre
7F-2, No.9. Prosperity
RD. I Science-Based
Industrial Park
Hsinchu ,300 Taiwan
14545 Valley View Ave.,
Suite "S"
Santa Fe Springs, CA
90670
98 Ford Road, Suite 3-F,
Denville, NJ 07834, USA
19 Colindale Avenue
London NW9 5DS UK
Tel: +886-3-5777364
Fax:+886-3-5773359
Tel: +1-562-926-4588
Fax:+1-562-926-7885
Tel: +1-973-664-0310
Fax:+1-973-664-0313
Tel:+44-(0)-20-8982-8200
Fax:+44-(0)-20-8201-3232
Sales Contact
info@zcom.com.tw
FAE Support
support@zcom.com.tw
Sales/Product Inquiries:
sales@zcomax.com
Tech Support/Questio ns:
support@zcomax.com
Sales Contact
sales@zcomax.co.uk
FAE Support
support@zcomax.co.uk
Z-Dotcom, Inc
China
Business
Centre 8 Nanjing,
168 Long Pan Zhong
Road, Jiangsu Software
Park, Suite 11
China 210002
Tel: +86-25-84661300
ax:+86-25-84661313
F
Sales Contact
sales@zcom.
com.cn
FAE Support
support@zcom.com.cn
Chapter 6 Service Information Page 20
Loading...