Z Com GZ901 Users Manual
GZ-901
900MHz Wir eless Network
Mini-PCI Adapter
Date of Issue: Dec. 14th, 2006
- 1 -
Technical Support
The firmware version of the 900 MHz Wireless Network Mini-PCI Adapter is displayed on the
utility About window. Users could download the most recent software version from the
supplier’s web site or refer to the selling contact for the latest software information. If you
have difficulty resolving the problem while installing or using the 900 MHz Wireless Network
Mini-PCI Adapter, please contact the supplier for support.
About This Manual
The 900 MHz Wireless Network Mini-PCI Adapter User Manual is first published on December,
2006. The manual includes procedures for the setup of the 900 MHz Wireless Network
Mini-PCI Adapter under Access Point. Take a moment to read through this manual and
familiarize yourself with wireless technology.
- 2 -
FCC Information
This device, 900 MHz Wireless Network Mini-PCI Adapter, complies with Part 15 of the FCC
Rules. Operation is subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference received; including
interference that may cause undesired operation.
Federal Communications Commission (FCC) Statement
This Equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Warning: Any changes or modifications to this unit not expressly approved by the
party responsible for compliance could void the user's authority to operate the
equipment.
Tested to comply with FCC standard. FOR HOME OR OFFICE USE.
FCC RF Radiation Exposure Statement:
1. This module is intended for OEM integrator. The OEM integrator is still responsible for the
FCC compliance requirement of the end product which integrates this module.
20cm minimum distance has to be able to be maintained between the antenna and the users
for the host this module is integrated into. Under such configuration, the FCC radiation
exposure limits set forth for an population/uncontrolled environment can be satisfied.
2. This device and its antenna(s) must not be co-located or operating in conjunction with any
other antenna or transmitter.
- 3 -
USERS MANUAL OF THE END PRODUCT:
In the users manual of the end product, the end user has to be informed to keep at
least 20cm separation with the antenna while this end product is installed and
operated. The end user has to be informed that the FCC radio-frequency exposure
guidelines for an uncontrolled environment can be satisfied. The end user has to
also be informed that any changes or modifications not expressly approved by the
manufacturer could void the user's authority to operate this equipment. If the size of
the end product is smaller than 8x10cm, then additional FCC part 15.19 statement is
required to be available in the users manual: This device complies with Part 15 of
FCC rules. Operation is subject to the following two conditions: (1) this device may
not cause harmful interference and (2) this device must accept any interference
received, including interference that may cause undesired operation.
LABEL OF THE END PRODUCT:
The final end product must be labeled in a visible area with the following
" Contains TX FCC ID: M4Y-GZ901 ". If the size of the end product is larger than
8x10cm, then the following FCC part 15.19 statement has to also
be available on the label: This device complies with Part 15 of FCC rules. Operation
is subject to the following two conditions: (1) this device may not cause harmful
interference and (2) this device must accept any interference received, including
interference that may cause undesired operation.
- 1 -
Table of Contents
Chapter 1 About Wireless Network Mini-PCI Adapter......................................2
1-1 Features and Benefits.......................................................................................................2
1-2 Applications..................................................................................................................... 3
1-3 Product Kit....................................................................................................................... 4
Chapter 2 Getting Started......................................................................................5
2-1 Before Installation ........................................................................................................... 5
2-2 Insert the 900MHz Wireless Network Mini-PCI Adapter............................................... 5
Chapter 3 Install Driver for Windows..................................................................6
3-1 Set up Wireless Network Mini-PCI Adapter for Windows XP .......................................6
3-2 Set up Wireless Network Mini-PCI Adapter for Windows 2000................................... 13
3-3 Set up Wireless Network Mini-PCI Adapter for Windows 98SE/ ME.......................... 18
Chapter 4 Configure the Wireless Network Mini-PCI Adapter ......................22
4-1 Install the WLAN Utility............................................................................................... 22
4-2 Use the WLAN Utility................................................................................................... 25
Limited W arranty.................................................................................................38
- 1 -
Chapter 1 About Wireless Network
Mini-PCI Adapter
The 900 MHz Wireless Network Mini-PCI Adapter is a standard PCI Card that fits into any
standard PCI slot in an Access Point. The 900 MHz Wireless Network Mini-PCI Adapter is an
enhanced high-performance that supports high-speed wireless networking at home, at office or
in public places. In addition, a detachable antenna version is specifically designed for system
integrator application. When installed, the 900 MHz Wireless Network Mini-PCI Adapter is able
to communicate with any 900 MHz compliant products.
1-1 Features and Benefits
1. Supports 1, 2, 5.5, 11 Mbps and up to 54Mbps data rate.
2. Direct Sequence Spread Spectrum (DSSS) technology provides robust,
interference-resistant and secure wireless connection.
3. Seamless connectivity to wired Ethernet and PC network LAN’s augments existing
networks quickly and easily.
4. Greater flexibility to locate or move networked PCs.
5. Wireless connection without the cost of cabling.
6. Easy to install and user friendly, just Plug and Play.
7. Low power consumption.
8. Supports a variety of operating systems (Win98SE/ME/2000/XP)
9. 64-bit, 128-bit and 152-bits WEP encryption capable.
10. Provides W indow-based Diagnostic Tools, most notably, Site Survey, Link Quality Test
and Access Point Browser.
11. Protection mechanism, which can avoid 11g packet and 11b packet colliding with each
other.
- 2 -
1-2 Applications
The 900 MHz Wireless Network Mini-PCI Adapter offers a fast, reliable, cost-effective solution
for wireless client access to the network in applications like these:
1. Remote access to corporate network information
E-mail, file transfer and terminal emulation.
2. Difficult-to-wire environments
Historical or old buildings, asbestos installations, and open area where wiring is difficult
to deploy.
3. Frequently changing environments
Retailers, manufacturers and those who frequently rearrange the workplace and change
location.
4. Temporary LANs for special projects or peak time
- Trade shows, exhibitions and construction sites where a temporary network will be
practical.
- Retailers, airline and shipping companies need additional workstations during peak
period.
- Auditors requiring workgroups at customer sites.
5. Access to database for mobile workers
Doctors, nurses, retailers, accessing their database while being mobile in the hospital,
retail store or office campus.
6. SOHO (Small Office and Home Office) users
SOHO users need easy and quick installation of a small computer network.
7. High security connection
The secure wireless network can be installed quickly and provide flexibility.
- 3 -
1-3 Product Kit
The 900 MHz Wireless Network Mini-PCI Adapter comes with the following items. Please go
through each item below. If any of listed items appears to be damaged or missing, please contact
your local dealer.
900 MHz Wireless Network Mini-PCI Adapter
z 900 MHz Wireless Network Mini-PCI Adapter……………….…………….. x 1
z 900 MHz Wireless Network Mini-PCI Adapter Software and Documentation
CD .....……………………………………………………………………….... x 1
- 4 -
Chapter 2 Getting Started
This chapter describes the instructions that guide you through the proper installation of your 900
MHz Wireless Network Mini-PCI Adapter for the Windows XP/2000/ME/98SE operating
systems.
The complete installation of the 900 MHz Wireless Network Mini-PCI Adapter consists of the
following steps:
STEP 1: Insert your 900 MHz Wireless Network Mini-PCI Adapter into the PCI slot on the
Access Point platform.
STEP 2: Power on the Access Point.
STEP 3: Finish Installation.
2-1 Before Installation
In addition to the items shipped with the client adapter, you will also need the following in order
to install the adapter:
1. A computer equipped with PCI slot.
2. Windows XP/2000/98SE/ME (with a Windows installation CD-ROM, diskettes for use
during installation).
3. Minimum 5 Mbytes free disk space for installing driver and utility program.
2-2 Insert the 900MHz Wireless Network Mini-PCI Adapter
To install the 900MHz Wireless Network Mini-PCI Adapter, please do the following:
1. Find an available PCI slot on your computer.
2. Insert the PCI Adapter into the PCI slot.
CAUTION: Do not force the client adapter into the slot. Forcing it will damage
both the client adapter and the slot. If the client adapter does not go in easily,
remove the card and reinsert it.
- 5 -
Chapter 3 Install Driver for Windows
This section describes the installation of the 900 MHz Wireless Network Mini-PCI Adapter
driver for the Windows 98SE/ME/2000 and Windows XP operating systems. The installation
procedures for Windows XP refer to 3-1 Set up Wireless Network Mini-PCI Adapter for
Windows XP; for Windows 2000 please see 3-2 Set up Wireless Network Mini-PCI Adapter for
Windows 2000; for Windows 98SE/ME refer to 3-3 Set up Wireless Network Mini-PCI Adapter
for Windows 98SE/ME.
Note: Before you start the installation, you are advised to keep the Windows
CD-ROM in case you might need certain system files.
3-1 Set up Wireless Network Mini-PCI Adapter for Windows
XP
Step 1: After inserting the 900 MHz Wireless Network Mini-PCI Adapter into the PCI slot on
your computer, the Windows will auto-detect the Wireless Network Mini-PCI Adapter and a
“Found New Hardware Wizard” window will show up. Select “Install from a list or specific
(Advanced) location” and press Next to install the driver.
- 6 -
Step 2: Insert the Product CD-ROM into the appropriate drive. Click on Next to install the
driver.
Step 3: The windows will appear the message about the Network Control has not passed
Windows Logo testing to verify its compatibility with Windows XP. Click on Continue
Anyway button to continue installing
- 7 -
Step 4: The windows will find “900 MHz Wireless Network Mini-PCI Adapter” and start
copying corresponding files into the system. Click on Next to continue.
Step 5: Click Finish to complete the installation.
- 8 -
Step 6: Right click “My Computer” from Start, select Properties, go to the Hardware tab
and click the Device Manager button to see if any exclamation mark appears next to the
Network Adapter/ 900 MHz Wireless Network Mini-PCI Adapter. If no, your 900 MHz
Wireless Network Mini-PCI Adapter is working well.
- 9 -
Loading...