Z Com AN622V01 Users Manual

FCC Statement

Warning: Changes or modifications to this unit not expressly approved by the
party responsible for compliance could void the user authority to operate the
equipment.

The device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) this d evice may not cause harmful
interference, and (2) this device must accept any interfere nce received, including interference that
may cause undesired operation.
The user’s manual or instruction manual for anintent ional or unintentional ra diator shall caution
the user that changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to com ply wit h the l imi ts for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a reside ntial installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and us ed in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television rec eption, which can be
determined by turning the equipment off and on, the use r i s encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from thatto w hi ch the r eceiver is
needed. Consult the dealer or an experienced radio/TV technician for help.

To comply with FCC RF exposure compliance requirements, a separation distance of at least 20 cm
must be maintained between the antenna of this device and all persons.
This Transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter
This device is intended only for OEM integ rators under the following conditions:

The antenna must be installed such that 20 cm is maintained between the antenna and users. For
laptop installations, the antenna must be installed to ensure that the proper spacing is maintained
in the event the users places the device in their lap during use (i.e. positioning of antennas mu st be
placed in the upper portion of the LCD panel only to ensure 2 0 cm will be maintained if the user
places the device in their lap for use) and The transmitter m o dul e may not be co-located with any
other transmitter or antenna. As long as the 2 cond itions above are met, further transmitter testing
will not be required.
However, the OEM integrator is still responsible for testing their end-product for any
additional compliance requirements required with this module installed (for example,
digital device emissions, PC peripheral requirements, etc.).

CAUTION:

IMPORTANT NOTE: In the event that these conditions can not be met(for example certain

laptop

configurations or co-location with another transmitter), then the FCC authorization is no

longer considered valid and the FCC ID can not be used on the final
product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end
product (including the transmitter) and obtaining a separate FCC authorization.

End Product Labeling

This transmitter module is authorized only for use in devices where the antenna may be installe d
such that 20 cm may be maintained between the antenna and users (for example access points,
routers, wireless ASDL modems, certain laptop configurations, and similar equipment). The final
end product must be labeled in a visible area wit h the following: "Contains TX FCC ID:M4Y-

AN622V01 ".

RF Exposure Manual Information That Must be Included

The users manual for end users must include the following inf o rmat ion in a prominent location
"IMPORTANT NOTE: To comply with FCC RF exposure compliance requirements, the antenna used
for this transmitter must be installed to provid e a separa tion distance of at least 20 cm from all
persons and must not be co-located or operating in conjunction with any other antenna or

transmitter."

Additional Information That Must be Provided to OEM Integrators

The end user should NOT be provided any instructions on how to remove or install the device.

This device is going to be operated in 5.15~5.25GHz frequency range, it is restricted in indoor
environment only.