Z Com 0XA622H Users Manual

FCC Statement

Warning: Changes or modifications to this unit not expressly approved by the
party responsible for compliance could void the user authority to operate the
equipment.

54Mbps IEEE802.11a Wireless Network Mini PCI Adapter complies with Part 15 of the FCC Rules.

complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions : (1) this devic e may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may cause undesired operation.
The user’s manual or instruction manual for an intentional or unintentional radiator shall caution the user that
changes or modifications not expressly approved by the party responsible for co mplianc e c ould void the
user’s authority to op erate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential insta llation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not occur in a particular insta llat ion. If this equipment
does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or mo re of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment in to an outlet on a circuit differe n t from that to which the receiver is needed.
Consult the dealer or an experienced radio/TV technician for help.

This device

To comply with FCC RF exposure co mplia nce req uire men ts, a separation distance of at least 20 cm must be
maintained between the antenna of this device and all persons.

This Transmitter must not be co-located or operat ing in conjunction with any other antenna or transmitter
This device is intended only for OEM integrat ors under the following conditions:

The antenna must be installed such that 20 cm is maintained between the antenna and users. For laptop
installations, the antenna must be installed to ensur e that the proper spacing is maintained in the even t the
users places the device in their lap during use (i.e. positioning of antennas must be placed in the upper
portion of the LCD panel only to ensu re 20 cm will b e maintained if t he user places t he device in their lap for
use) and The transmitter module may not be co-located with any other transmitter or antenna. As long as the
2 conditions above are met, further transmitter tes t ing will not be required.
However, the OEM integrator is still responsible for testing their end-product for any
additional compliance requirements required with this module installed (for example,
digital device emissions, PC peripheral requirements, etc.).

IMPORTANT NOTE:

configurations or co-location with another transmitter), then the FCC authorization is no longer considered
valid and the FCC ID can not be used on the final
product. In these circumstances, the OE M integrator will be responsible for re-evaluating the end product
(including the transmitter) and obtaining a separate FCC authorization.

End Product Labeling

This transmitter module is authorized only for use in devices where the antenna may be installed such that
20 cm may be main tained between th e antenna and us ers (for example access points, routers, wireless ASDL
modems, certain laptop configurations, and similar equipment). The final end product must be labeled in a
visible area with the following: "Contains TX FCC ID:M4Y-0XA622H ".

RF Exposure Manual Information That Must be Included

The users manual for end u sers must inc lude the fo llowing information in a pro minent locatio n "IMPORTANT
NOTE: To comply with FCC RF exp osure compliance requirements, the antenna used for this transmitter must
be installed to provide a separat ion distance of at lea st 20 cm from all persons and must not be co-located or
operating in conjunction with any other antenna or tra ns mitter."

Additional Information That Must be Provided to OEM Integrators

The end user should NOT be provided any instructions on how to remove or install the device.

Service Center in U.S.A

Company Name : Zcomax.
Company Address:14545 Val l e y View Ave., Suite S Santa Fe Springs, CA 906 70
Tel:[phone]

CAUTION:

In the event that these conditions can not be met (for example certain lap to p

1. Introduction

54Mbps IEEE802.11a Wireless Network Mini PCI Adapter

wireless network applications based on the IEEE 802.11a standard offering a data rate
of 54Mbps in a wireless LAN environment

XA-622H

access the web and network resource without the wire.

XA-622H

128 bit and 256 bit of WEP (Wired Equivalent Privacy) data encryption. With Direct
Spread Spectrum Signaling (DSSS) and Orthogonal Frequency Division Multiplexin g
(OFDM), domain access control, WEP encryption and group security, the modules will
safeguard all your wireless data transmissions from your nosy neighbors.

XA-622H

real-time information and online services anytime and anywhere.

is designed for Access Point, Router, and so forth. And give you wireless
provides high-speed access to network resources and has built-in 40/64-bit,

allows you to take full advantage of your devices mobility with access to

.

is the perfect solution for your

2. Feature

. Complies with IEEE 802.11a Standard for 5Hz Wireless LAN.
. Works with All Existing Network Infrastructures.
. Compatible with Wi-Fi Wireless Products and Services
. Capable of up to 256-Bit WEP Encryption.
. Freedom to Roam While staying Connected
. 54 Mbps High-Speed Transfer Rate
. Two UF-L Connectors for External Antenna
. Support Antenna diversity for Better Sensitivity
. Lower Power Consumption.