zBoost® YX550 DataBlast™
Series User Guide
Models:
• YX550 VLTE-AWS
• YX550 ALTE-AWS
zBoost products have a 30-day money back guarantee when purchased directly from
Wi-Ex®. If product is purchased from a reseller or third party, the purchaser is subject to the
policies of the third party.
1 Year Manufacturer Warranty. Register at www.Wi-Ex.com
v.020813
zBOOST® SOHO DATABLAST USER GUIDE
About zBoost® from Wi-Ex
Wi-Ex, the leader in cell phone signal boosters manufactures zBoost, the award-winning line
of cell phone signal boosters that enhance the performance of your cell phone, smartphone
and wireless data card.
Patented technologies protect the carrier network.
1-year manufacturer warranty – register your product at www.Wi-Ex.com.
zBoost products have more awards, more sales and more locations than all other signal
boosters…COMBINED.
®
FCC Information
FCC ID: SO4YX550-AWS-VLTE
SO4YX550-AWS-ALTE
Warning: Changes or modications to this device not expressly approved by Wi-Ex® could void the
user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If the equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment to an outlet on a circuit different from that to which the receiver is
connected
• Consult the dealer or an experienced radio/TV technician for help
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter. In accordance with FCC requirements of human exposure to radiofrequency
elds, the radiating element (antenna) shall be installed such that a minimum separation distance of
20cm (8in) is maintained from all persons.
Industry Canada Regulations
IC ID: 5544A-YX550AWSVLT
5544A-YX550AWSALT
This Class B digital apparatus meets all requirements of the Canadian Interference Causing
Equipment Regulations. Operation is subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
The term “IC:” before the radio certication number only signies that Industry Canada technical
specications were met.
RF Exposure: The manufacturer’s rated output power of this equipment is for single carrier
operation. For situations when multiple carrier signals are present, the rating would have to be
reduced by 3.5 dB, especially where the output is re-radiated and can cause interference to
i
zBOOST® SOHO DATABLAST USER GUIDE
adjacent band users. This power reduction is to be by means of input power or gain reduction and
not by an attenuator at the output of the device.
Cet appareillage numérique de la classe [B] répond à toutes les exigences de l’interférence
canadienne causant des règlements d’équipement. L’opération est sujette aux deux conditions
suivantes: (1) ce dispositif peut ne pas causer l’interférence nocive, et (2) ce dispositif doit accepter
n’importe quelle interférence reçue, y compris l’interférence qui peut causer l’opération peu désirée.
Le fabricant nominale de la puissance de sortie de ce matériel est simple transporteur. Pour les
situations lorsque plusieurs signauxporteurs sont présents, l’évaluation devrait être réduite de
3.5 dB, en particulier lorsque le signal de sortie est ré-émise et peut provoquer des interférences
adjacentes à la bande utilisateurs. Ce pouvoir est de la réduction par le biais de la sortie
d’alimentation ou la réduction de gain et non par un atténuateur à la sortie du dispositif.
Please note: This unit has been approved for use in Canada under RSS 131, however, consent
for the use of this device to improve cellular or PCS coverage, must be obtained through your
cellular or PCS provider, prior to placing the unit in operation. Please refer to the Industry Canada
document CPC 2-1-05, Section 6.1 available or viewable at:
http://www.ic.gc.ca/epic/site/smt-gst.nsf/en/sf08942e.html
Safety and Product Warranty Information
Copyright Notice
This manual is copyrighted. All rights reserved. This manual, whole or in part, may not be copied,
photocopied, reproduced, translated or reduced to any electronic medium or machine readable
form for distribution. This manual whole or in part, may not be modied without prior consent, in
writing, from Wireless Extenders.
Copyright © 2012 by Wireless Extenders, Inc.
Trademarks
Wireless Extenders, Wi-Ex, the Wi-Ex logo, zBoost, the zBoost logo and Extending Cell Zones are
registered trademarks of Wireless Extenders, Inc.
zBOOST® SOHO DATABLAST USER GUIDE
Package Contents: zBoost SOHO DataBlast
Before you begin, make sure all of the following parts came with your zBoost SOHO DataBlast
Literature Contents:
① Set-up overview for zBoost SOHO DataBlast
(User Guide online only)
Product Contents:
② zBoost Base Unit
③ Base Unit Antenna
④ Power Supply
⑤ RG-59 (mini) Coax Cable 50 feet
⑥ Signal Antenna
⑦ Signal Antenna Mounting Hardware
①
②
③
④
SETUP OVERVIEW
⑤
Safety Guidelines
In accordance with FCC requirements of human exposure to radiofrequency elds, the radiating
element (antenna) shall be positioned such that a minimum separation distance of 8 inches (20cm)
is maintained between the radiating element and the user and/or general population.
Limited Liability
In no event shall Wireless Extenders be liable for any direct, indirect, special, punitive, incidental,
exemplary or consequential damages, or any damages, whether in an action under contract,
negligence, or any other theory, arising out of or in connection with the set up of, use of, inability
to use, or performance of the information, services, products, and materials available from this
manual. These limitations shall apply notwithstanding any failure of essential purpose of any
limited remedy. Because some jurisdictions do not allow limitations on how long an implied
warranty last, or the exclusion or limitation of liability for consequential or incidental damages, the
above limitations may not apply to you.
For full warranty guidelines, see page 13.
Note
Changes or modications not expressly approved by
Wi-Ex® could void the user ’s authority to operate this
equipment and/or void the product warranty.
ii
⑥
⑦
iii
zBOOST® SOHO DATABLAST USER GUIDE
zBOOST® SOHO DATABLAST USER GUIDE
Optional zBoost Accessories Table of Contents
The following accessories are available to improve signal reception and provide increased coverage
in your home or ofce. Please see our website for complete selection.
To order, call 1-800-871-1612 or visit, www.Wi-ExStore.com
Part # Description
CANT-041 Wide Band Directional Signal Antenna, 700 - 2200 MHz (8 - 10.5 dBi)
YX012 Outside Grounding Kit
YX030-15W 15 ft. Signal Antenna coax extension, low-loss RG-6
YX030-35W 35 ft. Signal Antenna coax extension cable, low-loss RG-6
YX030-50W 50 ft. RG-6 cable
YX031-100W 100 ft. RG-11 cable
YX030-08W 8” at window entry cable
FCC Information ............................................................................................................................i
Industry Canada Regulations ........................................................................................................i
Safety and Product Warranty Information .................................................................................... ii
Copyright Notice ..........................................................................................................................ii
Trademarks ..................................................................................................................................ii
Safety Guidelines .........................................................................................................................ii
Limited Liability ............................................................................................................................ii
Package Contents: zBoost SOHO DataBlast .............................................................................. iii
Optional zBoost Accessories ...................................................................................................... iv
Table of Contents .......................................................................................................................... 1
Overview ........................................................................................................................................ 2
Why Indoor Signals Can Be Weak ............................................................................................... 2
Preparing to Set Up Your zBoost Product .................................................................................... 3
Tools Needed .............................................................................................................................. 3
Check for Signal Strength ........................................................................................................... 3
IMPORTANT: Before Installing, Note These Important Factors in Determining Performance ....... 4
Additional Cable Requirements ................................................................................................... 4
Grounding the Signal Antenna ..................................................................................................... 5
Securing Cable with a Drip Loop ................................................................................................. 5
Power Requirements ................................................................................................................... 5
Setting Up Your zBoost Signal Booster ....................................................................................... 6
Placement of the Signal Antenna ................................................................................................. 6
Antenna Bracket Assembly ......................................................................................................... 6
Positioning the Base Unit ............................................................................................................ 7
Running the Coaxial Cable from the Signal Antenna to the Base Unit. ........................................ 7
Connect the zBoost Base Unit to Power ...................................................................................... 8
Conrm That Your zBoost is Working Properly ............................................................................ 8
Improving Your Coverage Area ..................................................................................................... 9
zBoost Base Unit Light Indicators .............................................................................................. 10
Technical Specications ..............................................................................................................11
Frequently Asked Questions ...................................................................................................... 12
Warranty Information .................................................................................................................. 13
iv
1
zBOOST® SOHO DATABLAST USER GUIDE
zBOOST® SOHO DATABLAST USER GUIDE
Overview
Thank you for choosing zBoost. You will now be able to use your cell phone INSIDE your home or
ofce. Gone are the days when you had to go to the window upstairs or walk outside to use your
cell phone. Like a skylight that brings sunlight into your home, zBoost DataBlast transports and
amplies the outdoor 4G data signal into your home or ofce.
By following the easy instructions in this user guide, you will be Extending Cell Zones™ into your
home or ofce.
Why Indoor Signals Can Be Weak
There are several obstacles that can contribute to the poor reception you receive in your home or
ofce:
1. Location of the Cell Phone Tower in Relation to Your Home/Ofce
While cell phone providers have tried to place cell phone towers to provide the best overall
coverage, local ordinances and terrain features can impose restrictions on where these
towers can be placed, thus, limiting the signal strength available at your location.
2. Obstructions Caused by Buildings, Terrain and Trees
Cell phone signals can be completely blocked or reected by buildings, walls, trees, hills
and other terrain features resulting in low signal strength.
3. Energy Efcient Windows
These new windows can also affect signal penetration into the house.
Preparing to Set Up Your zBoost Product
Tools Needed
The following tools are needed to set up zBoost:
• #2 Phillips screwdriver
• Cellular phone operating in the band supported by your zBoost unit
• Drill (may be required for outdoor or attic antenna placement)
Check for Signal Strength
Before placing a zBoost in your home, make sure that you have fast/reliable data speeds on the
outside of your home, in the attic, at roof level or wherever you plan to place the Signal Antenna.
zBoost can only bring signal into your home when it reaches the Signal Antenna. If there is no
signal, zBoost will not work for you.
If a weak signal is available at ground level, check the signal strength in your attic or at roof level
location where the signal will likely be stronger and where the Signal Antenna can be placed for
best performance.
If you have reliable, fast data speeds outside your home, then zBoost can bring the signal into your
home.
If only one signal bar is displayed on your cell phone outside, indoor coverage will be
limited to one small room. We recommend placing the Signal Antenna outside and/or purchasing
a Wi-Ex upgrade Signal Antenna for increased coverage (see page iv).
Note
Cell phone signal bars are approximate and vary from
phone to phone. The number of bars can uctuate
widely, depending on the location of the phone, the
position or angle of the phone, weather, etc. Most cell
phone signal meters update every 6 to 10 seconds. An
increase of only one bar typically indicates a 4x to 10x
signal increase.
2
3
zBOOST® SOHO DATABLAST USER GUIDE
zBOOST® SOHO DATABLAST USER GUIDE
IMPORTANT: Before Installing, Note These Important Factors in Determining Performance
1. Atleast15vertical feetisneededbetweentheSignalAntenna(receivestheoutsidesignal)
andtheBaseUnitAntenna(rebroadcaststhesignalindoors).Separationlessthan15vertical
feetwillresultindecreasedperformance.
Iftheantennasaretooclosetogether,thelightontheBaseUnitwillashRED,indicatinga
problem-seetheBaseUnitLightIndicatorssection(page10).Tocapturethebestsignal,place
theSignalAntennaashighaspossible.
2. PositiontheSignalAntennaverticallyandkeepitatleast3feetaboveanymetal.
15’ of vertical
15’ of vertical
15’ of vertical
separation
separation
separation
Grounding the Signal Antenna
If the Signal Antenna is placed outdoors, it must be properly grounded. (See page iv for a
recommended grounding kit).
The setup must be in accordance with Article 810 of the National Electric Code (NEC). A listed
antenna discharge unit must be provided for the lead-in coaxial cable per NEC article 8.10.20 or the
shield of the coaxial cable must be permanently and effectively grounded in accordance with NEC
article 8.10.21. Please consult a professional installer or electrician for more information
Securing Cable with a Drip Loop
If the Signal Antenna is placed outdoors,
create a drip loop with the coaxial cable at
the point where the cable enters the building
through an outside wall. This can be done by
twisting and securing the cable into a loop
(no less than 4” across) near the entry point.
This will help prevent moisture from gathering
at entry point and leaking into the building.
Consult a professional installer for more
information.
Exterior Wall
Coax Cable
Power Requirements
The Base Unit can be plugged into a standard 2 or 3 prong 110 VAC receptacle using the included
power supply. The power supply consumes less than 10W (less than 0.2A).For more information on
power consumption, see “Technical Specications” on page 11.
Additional Cable Requirements
If the distance between the Signal Antenna and the Base Unit exceeds 50 feet, extension cables
are available on our website or at many home improvement and electronic stores. The included
cable is RG59-mini. For better performance, you may replace it with RG-6 cable for satellite TV.
The total cable length should not exceed 65 feet unless upgraded cable and/or upgraded Signal
Antenna (see page iv) is used. A longer cable is helpful only if it allows you to place the Signal
Antenna in a location where you measure stronger signal.
Cable Recommended Length
RG-59 mini (provided) Up to 50 feet
RG-6 Up to 65 feet
RG-11 Up to 120 feet
4
Warning
The zBoost SOHO DataBlast base unit MUST only be
used with the provided power adaptor. Use of other
power adaptors will void the warranty and may damage
the unit. Use of other equipment is not FCC approved.
5
zBOOST® SOHO DATABLAST USER GUIDE
zBOOST® SOHO DATABLAST USER GUIDE
Setting Up Your zBoost Signal Booster
Placement of the Signal Antenna
Choosing the best location for the Signal Antenna
provides the best performance and the largest
area of improved signal. Determine the location
that provides the strongest signal (generally found
on the roof ) using the signal strength indicator on
your cell phone.
In the area of best signal, identify the best
location for attachment of the mounting bracket
– such as an attic cross or main beam and
place the Signal Antenna at or near that location.
Important: Assemble the Signal Antenna
mounting bracket as shown below.
Keep the Signal Antenna at least 3 feet above
any metal such as wiring, A/C ducts, metal siding,
truss plates, etc. When connecting the cable to
the antenna, run the cable straight down from the
antenna. Avoid draping the coax near the antenna.
Note
Avoid placing the Signal Antenna near metal such as
wiring, A/C ducts, metal siding, truss plates, etc.
When connecting the cable to the antenna, run the
cable straight down from the antenna. Avoid draping
the coax near the antenna.
15’ of vertical
15’ of vertical
15’ of vertical
separation
separation
separation
Positioning the Base Unit
Assemble the Base Unit and Base
Unit Antenna and position the antenna
vertically. This Base Unit uses an omnidirectional antenna that delivers signal
in a circular pattern around the antenna.
Place the Base Unit in desired location –
where you want to create a Cell Zone™
For the widest possible signal area, it is
recommended that you position the Base
Unit near the middle of a room. The Base
Unit can be placed on a at surface (e.g.,
a bookshelf, desk, end table, etc.) and
performs best when located at least 4
feet above the oor or approximately the
height of a cell phone when it is typically
in use (avoid placing the Base Unit on the
oor).
Keep the Base Unit at least 2 feet away
from other cords, metal objects or other wireless devices such as wireless routers or wireless
access points. The zBoost DataBlast performs best when there are no obstructions between the
zBoost Base Unit and your mobile device.
Note: The Base Unit can be easily mounted on a wall by rst removing the Silver bracket from the
Base Unit (see “zBoost Base Unit Assembly” above) and using 2 mounting screws (not provided) to
afx to wall - keeping the antenna vertical.
Coaxial Cable
zBoost Base Unit
Power Supply
zBoost Base Unit Assembly
Remember, the zBoost DataBlast
requires at least 15 feet of vertical
separation between the Base Unit and
the Signal Antenna. Generally, increasing
this distance (up to 40 feet) will increase
the performance and decreasing the
distance will limit zBoost performance.
Base Unit Antenna
Base Unit Bracket
Figure A
Pole Bracket
Saddle
U-Bolt
Antenna Bracket Assembly
IMPORTANT: Incorrectly mounting the Signal
Antenna to the mounting bracket (see gure A) will
impede performance. Ensure that the Signal Antenna
is properly positioned in the mounting bracket as
pictured.
To mount antenna to a pole: Attach bottom of antenna
to pole bracket as pictured. Use U-Bolt to secure bracket
to pole and fasten.
To mount antenna to a at surface: Attach bottom
of antenna to pole bracket as pictured. Secure bracket
to desired surface using provided screws. Use of the
Saddle and U-Bolt are not necessary for this option.
6
Running the Coaxial Cable from the Signal Antenna to the Base Unit.
Use the provided 50 feet of RG-59 coax
cable to connect the Signal Antenna and
the Base Unit. Run the cable along a
descending pipe or through a wall that
leads closest to the location of the Base
Unit.
To run the cable from exterior to interior through a window, an 8 inch window-entry cable is
available for purchase (Part: YX030-08W). Should you need additional cable length, 15 foot, RG-6
extensions (Part: YX030-15W) are available at www.Wi-Ex.com.
Please note: the maximum recommended length for RG-6 is 65. For lengths above 65 feet, upgrade
to RG-11. Maximum recommended length for RG-11 is 120 feet.
NOTE: Refrain from securing cable or drilling holes until the system has been tested.
7
zBOOST® SOHO DATABLAST USER GUIDE
Pole Bracket
Saddle
U-Bolt
Figure A
zBOOST® SOHO DATABLAST USER GUIDE
Connect the zBoost Base Unit to Power
Connect the zBoost Base Unit to the provided power supply and plug into a power outlet.
Upon initial power up, a solid GREEN light should appear indicating normal conditions. If a RED
light appears, adjustments may be needed to optimize performance. If you nd the increased signal
coverage is acceptable, however, no additional adjustments are needed. See Base Unit Light
Indicator section (page 10) for more information.
Signal Antenna
Coaxial Cable
separation
15 ft
Base Antenna
Power Supply
zBoost Base Unit
Improving Your Coverage Area
Should you desire to improve coverage, you may:
• Relocate the Signal Antenna in order to capture a better signal –higher is usually better.
• Increase the distance between the Base Unit Antenna and the Signal Antenna.
• Purchase an upgrade antenna available at www.Wi-Ex.com
NOTE: The zBoost YX550 requires at least 15 feet of vertical separation between the Base
Unit and the Signal Antenna. Generally, increasing this distance (up to 40 feet) will increase the
performance and decreasing the distance will limit zBoost performance.
Keep the Base Unit off the oor and at least 2 feet away from other cords, metal objects or other
wireless devices such as wireless routers or wireless access points. The zBoost DataBlast performs
best when there are no obstructions between the zBoost Base Unit and your mobile device.
Note
Cell phone signal bars are approximate and vary from
phone to phone. The number of bars can uctuate
widely, depending on the location of the phone, the
position or angle of the phone, weather, etc. Most cell
phone signal meters update every 6 to 10 seconds. An
increase of only one bar typically indicates a 4x to 10x
signal increase.
Conrm That Your zBoost is Working Properly
1. Unplug the Base Unit power cord.
2. Turn off your cell phone.
3. Plug the power cord into the Base Unit.
4. Hold your cell phone about 5 feet from the Base Unit and then turn it on. Wait up to 1 minute
for the cell phone to register the signal coming from the Base Unit.
5. If the signal meter shows improvement, your zBoost unit is working properly.
When your zBoost system is in place and fully connected, walk throughout your home or ofce and
verify that you have fast, reliable data speeds. If the signal strength has improved, your zBoost
is working. Remember, coverage varies based on outdoor signal level, building construction, and
antenna placement. Coverage in adjoining rooms will be reduced by walls and building materials.
8
9
zBOOST® SOHO DATABLAST USER GUIDE
zBoost Base Unit Light Indicators Technical Specications
At Initial Power Up Only
Solid GREEN Normal condition at power up.
Slowly Alternating RED and GREEN zBoost is working, but at reduced performance and
Fast Flashing RED Indicates insufcient distance between the antenna and
Solid RED System is receiving signals from either the mobile
Fast Alternating RED and GREEN
followed by no light
coverage due to “non-ideal” setup.
Solution: Increase the distance between antenna
and amplier to achieve maximum performance and
coverage.
the amplier. The amplier is operating at signicantly
reduced coverage.
Solution: Increase space between base unit and
antenna.
device or the base station transceiver which are too
strong for proper operation.
Solutions: Move away from receiving antenna with
your cell phone. Move antenna away from other
devices..
The amplier is disabled.
Solution: Unplug your system and re-power.
zBOOST® SOHO DATABLAST USER GUIDE
Product Specications for zBoost YX550 SOHO DataBlast Series
Specications for VLTE
Band
Frequency
Band supported 13 17 4
Networks LTE (Verizon) LTE (AT&T) AWS
Output Power
General Specications for all zBoost DataBlast Models
System Gain 60dB
Power Consumption – Power Supply Current 3W standby; 7W max signal - 2.0A Max
Wall Supply Input ; Voltage 100-240VAC, 50-60 Hz; 5.0VDC
Input and Output Impedance TNC Connector: 50ohm; F Connector:75 ohm
System Certications FCC Parts 15 & 27, Industry Canada
Base Unit Size and Weight 5” x 7” x 1.25” – 9 oz.
Operating Conditions Indoor Use Only (40° - 105° F)
Coverage (open areas) Up to 2500 square feet
Uplink: 776 to 787MHz
Downlink: 746 to 757MHz
+20dBm in UL and
+13dBm in DL
This product uses patented technology to protect the carrier network
Specications for ALTE
Band
Uplink: 704 to 716MHz
Downlink: 734 to 746MHz
+20dBm in UL and
+13dBm in DL
Specications for AWS
Band
Uplink: 1710 to 1755MHz
Downlink: 2110 to 2155MHz
+20dBm in UL and
+10dBm in DL
Solid GREEN
Solid RED
After Initial Power Up
Normal condition
System is receiving signals from either the mobile
device or the base station transceiver which are too
strong for proper operation.
Solution: Unplug your system. Re-orient your Signal
Antenna and/or Base Unit to reduce the excessive
signal source. Plug your system back in. If still solid red,
call customer support 1-800-871-1612.
10
This product is covered by patent US 7,706,744. Other U.S. and
foreign patents pending.
11
zBOOST® SOHO DATABLAST USER GUIDE
zBOOST® SOHO DATABLAST USER GUIDE
Frequently Asked Questions
What can I expect my cell phone signal range and strength to be inside my home or ofce?
The closer you are to the base, the stronger the signal. This will vary with different conditions. Some
of the conditions that will affect the improved data coverage area are signal strength outdoors, the
type of building materials in the home, the placement of the unit and the antenna’s proximity to
cellular towers.
You can expect that your indoor coverage will be improved. You will experience faster, more reliable
data where you didn’t before. The degree of improvement will depend upon many factors. The
intent of zBoost products are to bring outside coverage inside. Just as the signal bars move up and
down when outside, the boosted signal will uctuate in a similar fashion.
Is a cellular phone signal booster the same as a wireless router; will it help my WiFi signal?
The Wi-Ex® unit will not help your WiFi service. The WiFi in your home or ofce operates on a
different frequency.
Why isn’t my cell phone indicating more signal with more bars?
You may not always observe more bars on your signal meter because of the signal spreading out
from the antenna. If your phone has a dB meter, 3dB is a signicant increase of 2x, 6dB is 4x, and
10dB is 10x. On a four bar phone, one "bar" equals about 10dB.
The increase in signal you will see depends upon:
• The level of signal at the Signal Antenna (outdoor)
• The care of the antenna placement (two feet away from metal, adequate antenna
separation [15 vertical feet of separation is recommended])
• The signal already present inside (related to building losses)
• The distance of your phone/device from the Base Unit (signal spreads or diminishes rapidly
with distance.)
There are usually several mobile devices in use at one time in my home, will your product
boost all of our signals simultaneously?
The zBoost SOHO DataBlast is designed to cover multiple signals simultaneously and will allow
multiple users to operate at the same time.
Does the zBoost work if you have no bars?
No, if no signal is present outdoors zBoost products will not work for you. Also, keep in mind if your
best signal is 1 bar at the Signal Antenna, your coverage will be limited to a small room. You could
improve that with an upgraded antenna (See page iv).
Warranty Information
Limited 1 Year Warranty
Register your product at www.Wi-Ex.com
Wi-Ex® warrants every Wi-Ex® product to be free from defects in material and workmanship under
normal use for the warranty period of one year.
Who Is Covered?
You must have proof of purchase to receive warranty service. A sales receipt or other
documentation showing the product purchased and the purchase date is considered proof of
purchase. This limited warranty extends only to the original consumer purchaser or any person
receiving the product as a gift from the original consumer purchaser and to no other purchaser or
transferee. This warranty does NOT extend to commercial users.
What is Covered?
Warranty coverage begins the day you purchase the product. For one year from the original
date, the Wi-Ex® Cell Phone Signal Booster will be repaired or replaced with a new, repaired,
refurbished or comparable product (whichever is deemed necessary by Wi-Ex® ) if it becomes
defective or inoperative. The exchange will be made without charge to you for parts and labor. You
will be responsible for the cost of shipping to the location designated by Wi-Ex®.
All products, including replacement products, are covered only for the original warranty period.
When the warranty on the original product expires, the warranty on the replacement product also
expires.
What is Excluded?
Your warranty does NOT cover:
• Labor charges for set up of the unit.
• Product replacement because of misuse, accident, lightning damage, unauthorized repair or
other cause not within the control of Wi-Ex®.
• Incidental or consequential damages resulting from the product. Some states do not allow
the exclusion of incidental or consequential damages, so the above exclusion may not apply
to you.
• Any modications or other changes to the product, including but not limited to software or
hardware modications in any way other than as expressly authorized by Wi-Ex® will void
this limited warranty.
• Product that has been modied or adapted to enable it to operate in any country other than
the country for which it was designed, manufactured, approved and/or authorized, or repair
of products damaged by these modications.
12
13
zBOOST® SOHO DATABLAST USER GUIDE
Make sure you keep…
Please keep your sales receipt or other document showing proof of purchase. Also, keep the
original box and packing material in case you need to return your product.
Before requesting repair service…
Make sure you have at least 15 feet of vertical separation between Signal Antenna and Base Unit
and that the Signal Antenna is at least 3 feet above metal.
If red light is on, system is receiving signals from either the mobile device or the base station
transceiver which are too strong for proper operation. Please unplug your system. Re-orient your
Signal Antenna and/or Base Unit to reduce the excessive signal source. Plug your system back in.
If still solid red, call customer support 1-800-871-1612.
To get warranty service…
Warranty service will be provided by Wi-Ex®. If you believe you need service for your unit,
contact Wi-Ex® at 1-800-871-1612 or support@wi-ex.com. A representative will go through a
diagnostic checklist with you. If it is determined that the product needs to be returned for service or
exchanged, you will receive a return merchandise authorization (RMA) number. The representative
will give you complete shipping details. Do not return products to Wi-Ex® without a Return
Authorization Number (RMA).
Reminder
Record the model and serial number found on the product below:
Model #: ___________________________________
Serial #: ___________________________________
Purchase Date: _____________________________
14
Loading...