zBoost YX110 Users Manual

Certification Exhibit

FCC ID: S04YX110

IC ID: 5544A-YX110

FCC Rule Part: CFR 47 Part 22 Subpart H, Part 24 Subpart E

IC Radio Standard Specification: RSS-131

ACS Report Number: 07-0255-LD

Applicant: Wireless Extenders Inc.

Model(s): YX110

Installation Guide

5015 B.U. Bowman Drive Buford, GA 30518 USA Voice: 770-831-8048 Fax: [phone]

ABOUT ZBOOST® FROM WI-EX®

zBoost zPocket YX110

Wi-Ex® is the leader in cell phone
signal boosters. zBoost® enhances the
performance of your cell phone, smart­phone, PDA and wireless data card.

Compatibility - Dual Band zBoosts®
are compatible with all U.S. carriers
regardless of technology

(except iDEN, Nextel).

Patent-pending technologies protect
the Carrier Network.

1-year manufacturer warranty ­register at www.Wi-Ex.com

zBoost® products have more awards,
more sales and more locations than
all other signal boosters ... COMBINED.

EASY TO SET UP:

zBoost
Base Unit

Pocket

P

Pocket

Power
Supply

1. Place the zBoost® base unit in a
window or where you receive at least
one bar. You must have some signal
where you place the zBoost® base
unit. It does not create signal.

2. Plug the power supply into an outlet
and connect the other end of the
power supply to the zBoost® base unit.

3. Place mobile device into the assembled
pocket. Use your speaker, headset or
Bluetooth device for mobility.

Note: If red light appears during set up or
any time during use, simply move the pocket
further away from the base unit.

* For questions, call 1-800-871-1612

or visit www.Wi-Ex.com

© 2008, Wi-Ex. All rights reserved.

THE ZB
W

For Your Personal
Workspace

OOST

®

P

RODUCT LINE

HICH ZBOOST® IS RIGHT FOR YOU

-

Creates a “Personal Cell Zone” for a
single user - covers your workspace

?

Great for Travel - Compact size,
zero installation - take your Cell

TM

Zone

with you!

Dual Band - (YX300) Works with
all phones* and U.S. carriers, in­creasing signal strength for voice
and data

For Your Car

Create an in-vehicle Cell Zone

TM

for

a multiple users simultaneously
Experience more miles of uninter-

rupted service

Dual Band - (YX

230) Works with

all phones* and carriers, increasing
signal strength for voice and data

For Your Home or
Oce

zBoost for the Home and Oce

boosts indoor cell coverage up to
2500 sq ft or up to 10,000 sq ft
with optional accessories

Supports multiple users
simultaneously

Three versions:

YX

500-CEL boosts 800 MHz*

YX500-PCS boosts 1900 MHz or
YX510 Dual Band boosts both

800 and 1900 MHz*

More zBoost products at www.Wi-Ex.com

Technical Specications
zBoost zPocket YX110

Frequency 1850 - 1990 MHz (1900 MHz) 824 - 894 MHz (800 MHz)
Gain 26dB (1900 MHz) 31dB (800 MHz)
Network Format CDMA, GSM, TDMA, GPRS, EDGE, 1xRTT, EVDO, HSDPA
Coverage distance from zBoost pocket is dependent upon headset or speaker range
Wall Supply Input 100-240VAC; 60Hz
Power Consumption 1W standby, 3W max signal
Imput/Output Impedance 50 Ω
Base Unit size/weight 4” x 5” x 1.3”/10 oz.
Operating Conditions Indoors Use Only 5

FCC Certicated. Industry Canada Certied.
Patents pending (including Network protection)

Handles all protocols and includes multiple patent pending technologies to provide low-cost coverage
while continually adapting to signals to prevent interference and remain transparent to the wireless
network. Provides an indicator if the antennas are positioned improperly, but will NOT suer damage or
interfere with the Carrier Network.

O

to 40OC (40O to 105OF)

*except iDEN, Nextel

v0208

.com

FCC Informaon

FCC ID: SO4YX110
Warning: Changes or modificaons to this device not expressly approved by Wi-Ex could void the user’s
authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protecon against
harmful interference in a residenal installaon. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instrucons, may cause harmful
interference to radio communicaons. However, there is no guarantee that interference will not occur in
a parcular installaon. If the equipment does cause harmful interference to radio or television recepon,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separaon between the equipment and receiver.

• Connect the equipment to an outlet on a circuit different from that to which the receiver is
connected.

• Consult the dealer or an experienced radio/TV technician for help.

RF Exposure

This equipment complies with FCC radiaon exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 8” (20cm) between the pocket
and your body. This transmier must not be co-located or operang in conjuncon with any other
antenna or transmier.

Industry Canada Regulaons

IC: 5544A-YX110
This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment
Regulaons. Operaon is subject to the following two condions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may
cause undesired operaon.
The term “IC:” before the radio cerficaon number only signifies that Industry Canada technical
specificaons were met.

Cet appareillage numérique de la classe B répond à toutes les exigences de l’interférence canadienne
causant des règlements d’équipement. L’opéraon est sujee aux deux condions suivantes: (1) ce
disposif peut ne pas causer l’interférence nocive, et (2) ce disposif doit accepter n’importe quelle
interférence reçue, y compris l’interférence qui peut causer l’opéraon peu désirée.
Le terme "IC" avant que le nombre par radio de cerficaon signifie seulement que des caractérisques
techniques du Canada d'industrie ont été rencontrées

RF Exposure:

The Manufacturer's rated output power of this equipment is for single carrier operaon. For situaons

when mulple carrier signals are present, the rang would have to be reduced by 3.5 dB, especially

where the output signal is re-radiated and can cause interference to adjacent band users. This power

reducon is to be by means of input power or gain reducon and not by an aenuator at the output of
the device.