zBoost VLTE-AWS Setup Overview

BASE UNIT LED INDICATORS

At Initial Power Up Only

After Initial Power Up

Fast Flashing RED

Solid RED

Solid GREEN

Slowly Alternating
RED and GREEN

zBoost is working, but at reduced performance and coverage due to
“non-ideal” setup. Increase the distance between antenna and
amplifier to achieve maximum performance and coverage.

Normal condition at power up.

Indicates insufficient distance between the antenna and the amplifier.
The amplifier is operating at significantly reduced coverage.

System is receiving signals from either the mobile device or the base
station transceiver which are too strong for proper operation.

Fast Alternating
RED and GREEN
followed by no light

The amplifier is disabled.

Solid GREEN

Solid RED

Normal condition

System is receiving signals from either the mobile device or the base
station transceiver which are too strong for proper operation.
Unplug your system and re-orient the Signal Antenna and/or Base
Unit to reduce excessive signal. If LED remains RED after
reconnecting power, contact customer support at 1-800-871-1612.

SETUP OVERVIEW

zBoost

®

DataBlast

TM

YX550 Upgrade

Rev B

SETTING UP YOUR zBOOST® SIGNAL BOOSTER

zBoost DataBlast 4G signal booster extends a 4G Data Zone™ for multiple users/
devices operating on the 4G network specified on the front of the box. The zBoost
DataBlast upgrade system boosts data speeds by up to 20 times when integrated with
your existing cellular signal boosting system.

Important: By joining two signal boosters to a single exterior antenna, the
signal could be reduced by as much as 3dB.

Before installing, please note the following important factors in determining your zBoost
performance:

• At least 15 vertical feet is needed between the Signal Antenna (receives the
outside signal) and the Base Antenna (rebroadcasts the signal indoors). Separation
less than 15 vertical feet will result in decreased performance.

• Keep the Signal Antenna at least 3 feet above any metal.

Boost data transmission in 4 easy steps:

FIRST: Replace existing Signal Antenna with zBoost Quad Band Antenna.

Verify that the location of the Signal Antenna is in the area of strongest signal. The
coverage your zBoost DataBlast provides is largely determined by the quality of signal
received by the Signal Antenna. If your best signal is 1 bar, your coverage will be
limited to one small room.

To maximize signal coverage, place the Signal Antenna where you find the strongest
signal (up high or outside) and at least 3 feet above any metal.

IMPORTANT: Incorrectly mounting the Signal Antenna to the mounting bracket (see
figure A) will impede performance. Ensure that the Signal Antenna is properly
positioned in the mounting bracket as pictured.

To mount antenna to a pole: Attach bottom of antenna to pole bracket as

pictured. Use U-Bolt to secure bracket to pole and fasten.
To mount antenna to a flat surface: Attach bottom of antenna to pole bracket

as pictured. Secure bracket to desired surface using provided screws. Use of
the Saddle and U-Bolt are not necessary for this option.

Download the YX550-Upgrade User Guide at www.Wi-Ex.com

SECOND: Disconnect the coaxial cable from the existing booster Base Unit and
connect to the zBoost Signal Combiner.

Existing RG-59 or RG-6 should not exceed 50 feet. If the cable length exceeds 50 feet,
it should be replaced with RG-11. Existing RG-11 should not exceed 100 feet.

The zBoost DataBlast requires at least 15 feet of vertical separation between the Base
Unit and the Signal Antenna. Generally, increasing this distance (up to 40 feet) will
increase the performance and decreasing the distance will limit the performance of
both boosters.

THIRD: Connect one end of the zBoost Signal Combiner to the DataBlast Base
Unit and connect the remaining end to the existing booster.

Assemble the Base Unit and Base Unit Antenna and position the antenna vertically.
Place the Base Unit next to your existing signal booster. For the widest possible signal
area, it is recommended that you position the Base Unit near the middle of a room.
The Base Unit can be placed on a flat surface (e.g., a bookshelf, desk, end table, etc.)
and performs best when located at least 4 feet above the floor or approximately the
height of a cell phone when it is typically in use (avoid placing the Base Unit on the
floor).

Keep the Base Unit at least 2 feet away from other cords, metal objects or other
wireless devices such as wireless routers or wireless access points. The zBoost
DataBlast performs best when there are no obstructions between the zBoost Base
Unit and your mobile device.

Important: The cable connections should remain hand-tight. Once you have them in
their permanent location, verify that all three connections remain secure.

Note: To mount it on an interior wall, first remove the silver bracket from the Base Unit,
mount the bracket to a wall with 2 screws (not provided), then placing the Base Unit
back into the bracket keeping the antenna vertical.

PACKAGE CONTENTS

zBoost Base Unit with

Silver Mounting Bracket

Base Unit Antenna

zBoost Signal Combiner

Power Supply

Quad Band Signal

Antenna (2 pieces) and

Mounting Hardware

SETUP OVERVIEW

Setup Overview

User Guide available

at www.Wi-Ex.com

FOURTH: Connect the DataBlast Base Unit to the provided power supply and
plug into a power outlet.

When your zBoost system is in place and fully connected, walk throughout your home
or office and verify that you have fast, reliable data speeds. If the signal strength has
improved, your zBoost is working. Remember, coverage varies based on outdoor
signal level, building construction, and antenna placement. Coverage in adjoining
rooms will be reduced by walls and building materials.

Upon initial power up, a solid GREEN LED should appear indicating normal conditions.
If a RED light appears, adjustments may be needed to optimize performance. If you
find the increased signal coverage is acceptable, however, no additional adjustments
are needed. See LED Indicator section for more information.

Should you desire to improve coverage, you may:

• Relocate the Signal Antenna in order to capture a better signal–higher is better.

• Increase the distance between the Base Units and the Signal Antenna.

Models:

• VLTE-AWS

• ALTE-AWS

Figure A

Cell Tower

15 ft

separation

Power Supply

15 ft

separation

CEL

Existing
Coaxial Cable

Signal Antenna

DataBlast Base Unit

Figure A

ration
se

p

a
r

pa
r

D

ataBla

Pole Bracket

Saddle

U-Bolt

Existing
Signal Booster

Signal
Combiner

For questions or assistance, contact Wi-Ex customer service at 1-800-871-1612
or email [e-mail].

LIMITED 1 YEAR WARRANTY | REGISTER AT WWW.WI-EX.CO M

Wi-Ex warrants every Wi-Ex product to be free from defects in material and workmanship under normal use for the warranty period of 1 year.

Who Is Covered?

You must have proof of purchase to receive warranty service. A sales receipt or other documentation showing the product purchased and
the purchase date is considered proof of purchase. This limited warranty extends only to the original consumer purchaser or any person
receiving the product as a gift from the original consumer purchaser and to no other purchaser or transferee. This warranty does NOT
extend to commercial users.

What is Covered?

Warranty coverage begins the day you purchase the product. For one year from the original date, the Wi-Ex Cell Phone Signal Booster
will be repaired or replaced with a new, repaired, refurbished or comparable product (whichever is deemed necessary by Wi-Ex) if it
becomes defective or inoperative. The exchange will be made without charge to you for parts and labor. You will be responsible for the
cost of shipping to the location designated by Wi-Ex. If Wi-Ex cannot reasonably repair or replace the unit then Wi-Ex may, at its sole
discretion, refund the price you paid for the product or the price of the unit. All products, including replacement products, are covered only
for the original warranty period. When the warranty on the original product expires, the warranty on the replacement product also expires.

What is Excluded?

Your warranty does NOT cover:

• Labor charges for set up of the unit.

• Product replacement because of misuse, accident, lightning damage, unauthorized repair or other cause not within the control of Wi-Ex.

• Incidental or consequential damages resulting from the product. Some states do not allow the exclusion of incidental or consequential
damages, so the above exclusion may not apply to you.

• Any modifications or other changes to the product, including but not limited to software or hardware modifications in any way other
than as expressly authorized by Wi-Ex will void this limited warranty.

• Product that has been modified or adapted to enable it to operate in any country other than the country for which it was designed,
manufactured, approved and/or authorized, or repair of products damaged by these modifications.

Make sure you keep…

Please keep your sales receipt or other document showing proof of purchase. Attach it to this Setup Overview and keep both nearby.
Also, keep the original box and packing material in case you need to return your product.

Before requesting repair service…

Please review the BASE UNIT LED INDICATORS section listed in this overview - This may save you a call.

To get warranty service…

Warranty service will be provided by Wi-Ex. If you believe you need service for your unit, contact Wi-Ex at 1-800-871-1612 or
[e-mail]. A representative will go through a diagnostic checklist with you. If it is determined that the product needs to be
returned for service or exchanged, you will receive a return merchandise authorization (RMA) number. The representative will give you
complete shipping details. Do not return products to Wi-Ex without a Return Authorization Number (RMA).

Reminder: Record the model and serial number found on the product below:

Model #:

Serial #:

Purchase Date:

The zBoost SOHO DataBlast YX550 Upgrade User Guide and additional product information is
available at www.Wi-Ex.com

CUSTOMER SERVICE

WARRANTY INFORMATION

FCC Information

FCC ID: SO4YX550-AWS-VLTE
SO4YX550-AWS-ALTE

Warning: Changes or modifications to this device not expressly approved by Wi-Ex could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If the equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and receiver

• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected

• Consult the dealer or an experienced radio/TV technician for help

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located
or operating in conjunction with any other antenna or transmitter. In accordance with FCC requirements of human exposure to radiofrequency
fields, the radiating element (antenna) shall be installed such that a minimum separation distance of 20cm (8in) is maintained from all persons.
Additionally, the device must not be used above 10 m above ground.

Industry Canada Regulations

Canada IC: 5544A-YX550AWSVLT
5544A-YX550AWSALT

This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations. Operation is subject to
the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.

The term “IC:” before the radio certification number only signifies that Industry Canada technical specifications were met.
RF Exposure:

The manufacturer’s rated output power of this equipment is for single carrier operation. For situations when multiple carrier signals are present,
the rating would have to be reduced by 3.5 dB, especially where the output is re-radiated and can cause interference to adjacent band users.
This power reduction is to be by means of input power or gain reduction and not by an attenuator at the output of the device.

Please note: This unit has been approved for use in Canada under RSS 131, however, consent for the use of this device to improve cellular or
PCS coverage, must be obtained through your cellular or PCS provider, prior to placing the unit in operation. Please refer to the Industry
Canada document CPC 2-1-05, Section 6.1 available or viewable at: http://www.ic.gc.ca/epic/site/smt-gst.nsf/en/sf08942e.html

Cet appareillage numérique de la classe [B] répond à toutes les exigences de l’interférence canadienne causant des règlements d’équipement.
L’opération est sujette aux deux conditions suivantes: (1) ce dispositif peut ne pas causer l’interférence nocive, et (2) ce dispositif doit accepter
n’importe quelle interférence reçue, y compris l’interférence qui peut causer l’opération peu désirée.

Le fabricant nominale de la puissance de sortie de ce matériel est simple transporteur. Pour les situations lorsque plusieurs signaux porteurs
sont présents, l’évaluation devrait être réduite de 3.5 dB, en particulier lorsque le signal de sortie est ré-émise et peut provoquer des
interférences adjacentes à la bande utilisateurs. Ce pouvoir est de la réduction par le biais de la sortie d’alimentation ou la réduction de gain
et non par un atténuateur à la sortie du dispositif.

Frequency

Uplink: 776 to 787MHz
Downlink: 746 to 757MHz

Uplink: 704 to 716MHz
Downlink: 734 to 746MHz

Uplink: 1710 to 1755MHz
Downlink: 2110 to 2155MHz

Band supported 13 17 4

Networks LTE (Verizon) LTE (AT&T) AWS

Output Power +20dBm in UL and +13dBm in DL +20dBm in UL and +13dBm in DL +20dBm in UL and +10dBm in DL

System Gain 60dB

Power Consumption – Power Supply Current 3W standby; 7W max signal - 2.0A Max

Wall Supply Input ; Voltage 100-240VAC, 50-60 Hz; 5.0VDC

Input and Output Impedance TNC Connector: 50ohm; F Connector:75 ohm

FCC Parts 15 & 27, Industry Canada

Base Unit Size and Weight 5” x 7” x 1.25” – 9 oz.

Operating Conditions Indoor Use Only (40° - 105° F)

Important: By joining two signal boosters to a single exterior antenna, the signal could be reduced by as much as 3dB

This product uses patented technology to protect the carrier network