Zavio B5111, B5210 Quick Installation Manual

0

8608551000010

/ B5210

1

Zavio B5111/ B5210 Quick Installation Guide

Please follow the installation steps below to set up your B5111/ B5210 Bullet IP Camera. Check the package contents against the list below. See P.1 Physical overview. See P.2 LED Indicator Definition. See P.2 Install the hardware and connect all cables. See P.3 Microsoft OS: Use the software CD to install Intelligent IP Installer. See P.3 Access the IP Camera using Intelligent IP Installer. See P.4 Mac OS using Safari Broswer. See P.6 Lighting environment setting. See P.6 Change the Web Interface into your preferred language. See P.7 Application of IP Camera. See P.7 For more information, please check the User Manual available in the Software CD or you can download the latest software from http://www.zavio.com

Package Contents

Camera

B5111/ B5210 IP Camera

Quick Installation Guide

Brief product information and quick installation

Software CD

IP Surveillance Software Intelligent IP Installer User Manuals Language Packs

Accessory

(1) Three-axis wall/ ceiling mounting bracket (2) Screws and anchors for wall/ ceiling mounting (3) Sun Shield (4) Screws for sun shield (5) Cat 5e Female Coupler

2

Physical Overview

LED Indicator Definition

LED

Indication

Power

Steady red for booting up process.

Steady blue for booting up completion.

Flash purple for FW upgrading.

Network

Flash yellow while Network activity.

MicroSD Card

Steady yellow means MicroSD card ready.

Flash yellow while accessing MicroSD card.

Reset: When the device is empowered, press the Reset Button to reboot the device, or hold the Reset Button for 10 seconds to the settings back to factory default. Reset process: Press reset button until indicator Unlitsteady red (booting up process)steady blue (booting up completion)

Reset to default process: Press until indicator steady bluesteady red (booting up process) steady blue (booting up completion)

3

Install the hardware and connect all cables

a. Wall mounting and Ceiling mounting

1. Use the 2 supplied screws to fix the base plate to a flat surface.

2. Loosen the screws on the bracket to aim the shooting area.

3. Tighten the screws at the two joints of the bracket.

b. Connet all cables

Microsoft OS: Use the software CD to install Intelligent IP Installer

Power on your PC and insert the CD-ROM. The setup page will show up automatically. Please follow these steps to install the firmware. Selet “Intelligent IP Installer” and follow the installation process to complete the installation.

b1. Without Power over Ethernet (PoE) connection

1. Connect the 12V power adaptor to the IP Camera.

2. Using a standard RJ-45 network cable, connect the IP Camera to a normal Hub/ Switch/ Router.

b2. Power over Ethernet (PoE)

Using a standard RJ-45 network cable, connect the IP Camera to a PoE-enabled Hub/ Switch/ Router.

4

Access the IP Camera using Intelligent IP Installer

1. Please check two settings before using Intelligent IP Installer.

b. Browser’s Internet Properties  Security

 Default Level

a. Browser’s Internet Properties  Privacy

 Uncheck Pop-up Blocker

2. Click the Intelligent IP Installer Icon on your desktop. The main page will show up listing all active camera and video server devices. Select the relevant IP camera from the list and click Link to IE.

3. Enter your Username and Password to login to the IP Camera. (Default is admin / admin)

5

4. When accessing the IP Camera for the first time, a yellow information bar appears below the

address bar: This website wants to install the following add-on: ‘AxvideoView.cab from ‘Zavio Inc’.

5. Click the information bar, and select Install ActiveX control.

6. Click Install.

7. Live video displays in the centre of your web browser.

6

Mac OS using Safari Browser

Lighting environment setting

The default setting of lighting environment is Auto. However, you may also select 50 or 60 Hz upon the lighting environment of your country. Go to “Setting > Live View > Camera Setting > Image Setting”, select the environment setting you wish.

1. Select Safari icon

2. Click Bonjour function and select the camera you wish to access.

3. Enter name and password to login to the IP camera. (Default is admin / admin)

4. The monitor image will be displayed in your browser.