ZAVIO 5117F User Manual

Download

Page 1

F7110 / F7115 User Manual

F7110/ F7115

Page 2

F7110 / F7115 User Manual

Contents

CHAPTER 1. SAFETY INSTRUCTION ....................................................................................................................... 1

CHAPTER 2. MINIMUM SYSTEM REQUIREMENT &...........................................................................................3

PRODUCT FEATURE..................................................................................................................................................... 3

2.1 SYSTEM REQUIREMENT ..........................................................................................................................................3

2.2 PRODUCT FEATURES ............................................................................................................................................... 4

CHAPTER 3. USING IP CAMERA VIA WEB BROWSER ........................................................................................5

3.1WINDOWS WEB BROWSER....................................................................................................................................... 5

3.2 MAC WEB BROWSER............................................................................................................................................... 5

CHAPTER 4. SETTING UP WIRELESS CONFIGURATION (ONLY FOR F7115 ) ............................................... 8

CHAPTER 5. OPERATING IP CAMERA VIA MOBILE PHONE ........................................................................... 9

5.1 MOBILE PHONE VIEWING ..................................................................................................................................... 10

5.2 USING IP CAMERA VIA IPHONE .............................................................................................................................11

CHAPTER 6. MSN MESSENGER............................................................................................................................... 11

CHAPTER 7. CONFIGURATION OF MAIN MENU................................................................................................ 15

Full screen................................................................................................................................................................ 1

Snapshot................................................................................................................................................................... 1

7.1 LIVE VIEW ............................................................................................................................................................. 15

computer computer.................................................................................................................................................. 16

7.2 SETTING ................................................................................................................................................................. 18

7.3 CLIENT SETTING ................................................................................................................................................... 18

7.3.3 Protocol.......................................................................................................................................................... 19

7.4 IMAGE SETUP......................................................................................................................................................... 20

7.5 PT CONTROL .........................................................................................................................................................20

CHAPTER 8. SETTING-BASIC................................................................................................................................... 22

8.1 SYSTEM .................................................................................................................................................................. 22

8.1.1 Information....................................................................................................................................................22

8.1.2 Date / Time..................................................................................................................................................... 23

8.1.3 Initialize......................................................................................................................................................... 24

8.1.4 Language....................................................................................................................................................... 25

8.2 CAMERA................................................................................................................................................................. 26

8.2.1 General.......................................................................................................................................................... 26

8.2.2 H.264..............................................................................................................................................................28

8.2.3 MPEG-4......................................................................................................................................................... 29

8.2.4 MJPEG.......................................................................................................................................................... 31

8.2.5 3GPP.............................................................................................................................................................. 32

8.2.6 Advanced........................................................................................................................................................ 33

8.2.7 PLAYBACK ................................................................................................................................................... 35

8.3 NETWORK .............................................................................................................................................................. 36

8.3.1 Information....................................................................................................................................................36

8.3.2 PPPoE (Point-to-Point Protocol over Ethernet)........................................................................................... 37

8.3.3 DDNS (Dynamic DNS)................................................................................................................................. 39

8.3.4 UPnP (Universal Plug and Play)..................................................................................................................43

8.3.5 Bonjour.......................................................................................................................................................... 43

8.3.6 IP Notification...............................................................................................................................................45

8.3.7 Wireless (Only for F7115)............................................................................................................................. 46

8.3.8 WPS ............................................................................................................................................................... 48

8.3.9 Messenger ...................................................................................................................................................... 49

8.4 SECURITY............................................................................................................................................................... 51

8.4.1 Account.......................................................................................................................................................... 51

8.4.2 HTTPS........................................................................................................................................................... 52

Page 3

F7110 / F7115 User Manual

8.4.3 IP Filter .........................................................................................................................................................

53

CHAPTER 9. SETTING-ADVANCED ........................................................................................................................53

9.1 PTZ CONTROL ...................................................................................................................................................... 54

9.1.1 Setting............................................................................................................................................................54

9.2 PRESET POSITION..................................................................................................................................................54

9.2.1 Setting............................................................................................................................................................55

9.2.2 Alarm Sending............................................................................................................................................... 56

9.3 PAT ROL ..................................................................................................................................................................57

9.4 FTP CLIENT........................................................................................................................................................... 58

9.4.1 General.......................................................................................................................................................... 59

9.4.2 Alarm sending............................................................................................................................................... 60

9.4.3 Periodical sending......................................................................................................................................... 62

9.5 SMTP ....................................................................................................................................................................63

9.5.1 General.......................................................................................................................................................... 63

9.5.2 Alarm sending................................................................................................................................................ 65

9.6 NETWORK STORAGE.............................................................................................................................................. 68

9.6.1 General.......................................................................................................................................................... 68

9.6.2 Alarm sending................................................................................................................................................ 69

9.6.3 Periodical recording......................................................................................................................................71

9.7 MEMORY CARD ..................................................................................................................................................... 72

9.7.1 General.......................................................................................................................................................... 72

9.7.2 Alarm sending................................................................................................................................................ 74

9.7.3 Periodical recording......................................................................................................................................75

9.7.3 Backup........................................................................................................................................................... 76

9.8 HTTP EVENT.........................................................................................................................................................77

9.7.1 General.......................................................................................................................................................... 77

9.7.2 Alarm sending................................................................................................................................................ 78

9.8 ALARM OUTPUT .................................................................................................................................................... 82

9.9 SCHEDULE.............................................................................................................................................................. 84

9.10 ALARM INPUT ...................................................................................................................................................... 84

9.11 ALARM BUFFER ................................................................................................................................................... 85

9.12 MOTION DETECTION........................................................................................................................................... 87

9.13 AUDIO DETECTION .............................................................................................................................................. 88

9.14 SYSTEM LOG........................................................................................................................................................ 89

CHAPTER 10. APPENDIX ........................................................................................................................................... 90

A. FRAME-RATE AND BITRATE TABLE – HELP TO SET IPCAMERA WITH YOUR NETWORK ENVIRONMENT TO ACCESS

INTERNET......................................................................................................................................................................90

A.1 Mega Mode...................................................................................................................................................... 90

A.2 VGA Mode........................................................................................................................................................ 93

B. STORAGE REQUIREMENT TABLE - HELP TO SET RECORDING STORAGE SYSTEM.................................................... 96

B.1 Mega Mode...................................................................................................................................................... 96

B.2 VGA Mode........................................................................................................................................................ 98

C. SYSTEM REQUIREMENT – HELP TO SETUP SYSTEM .............................................................................................. 100

C.1. 16 Channel IPCamera with CIF Performance............................................................................................ 100

C.2. 16 Channel IPCamera with D1 Performance.............................................................................................. 100

EUROPE – EU DECLARATION OF CONFORMITY............................................................................................ 101

FEDERAL COMMUNICATION COMMISSION INTERFERENCE STATEMENT .......................................... 103

Page 4

F7110 / F7115 User Manual

User Manual

Chapter 1. Safety Instruction

 Before you use this product

This product has been designed with safety in mind. However, the electrical products can cause fires which may lead to serious body injury if not used properly. To avoid such accidents, be sure to heed the following.

 Legal Caution

Video and audio surveillance can be forbidden by laws that vary from country to country. Check the laws in your local region before using this product for surveillance purposes.

 Don't open the housing of the product

Don't try to open the housing or remove the covers which may expose yourself to dangerous voltage or other hazards.

 Don't use the accessories not recommend by the manufacturer

 Heed the safety precautions

Be sure to follow the general safety precautions and the “Operation Notice.”

 Operation Notice - Operating or storage location

Avoid operating or storing the camera in the following locations:

 Extremely hot or cold places

(Operating temperature: 0 °C to + 50 °C [32 °F to 122°F] )

 Exposed to direct sunlight for a long time, or close to heating equipment (e.g., near heaters)  Close to water (e.g.,near a bathtub, kitchen sink, laundry tub)  Close to sources of strong magnetism  Close to sources of powerful electromagnetic radiation, such as radios or TV transmitters  Locations subject to strong vibration or shock

 In case of a breakdown

In case of system breakdown, discontinue use and contact your authorized dealer.

Safety Instruction

Page 5

F7110 / F7115 User Manual

 In case of abnormal operation

 If the unit emits smoke or an unusual smell,  If water or other foreign objects enter the cabinet, or  If you drop the unit or damage the cabinet:1 Disconnect the cable and the connecting cables. 2

Contact your authorized dealer or the store where you purchased the product.

 Transportation

When transporting the camera, repack it as originally packed at the factory or in materials of equal quality.

 Ventilation

To prevent heat buildup, do not block air circulation around the device.

 Cleaning

 Use a soft, dry cloth to clean the external surfaces of the device. Stubborn stains can be

removed using a soft cloth dampened with a small quantity of detergent solution, then wipe dry.

 Do not use volatile solvents such as alcohol, benzene or thinners as they may damage the

surface.

Safety Instruction

Page 6

F7110 / F7115 User Manual

Chapter 2. Minimum System Requirement &

Product Feature

2.1 System Requirement

For normal operation and viewing of the network camera, it’s recommended that your system meet these minimum requirements for proper operation:

Item Requirements

CPU

Graphic Card 64 MB RAM graphic cards(or equivalent on-board graphic cards)

RAM 512 MB

Operating System

Pentium 4 1.8GHz (or equivalent AMD)

Windows 98, Windows ME (Please see Note) Windows2000, 2003, XP, Vista, Mac OS X Leopard

Web Browser Internet Explore 6 or later

Note:

1. If using Windows 98 or Windows ME, please install IP Installer before using WEB UI to ensure the system runs normally.

2. If not able to view the recorded video file, please install Xvid codec while installing

Intelligent IP Installer. (For Windows 98, ME or 2000 server, the codec might not work

properly. Please download Xvid codec 1.0 from the internet.)

3. Please keep updating the latest Windows software and service package. (Ex: Net

Framework, Windows Media Player, Enhance ActiveX Security)

Minimum System Requirement & Product Feature

Page 7

F7110 / F7115 User Manual

2.2 Product Features

These easy-to-follow instructions make setup and operation quick and simple, so you’ll also soon be enjoying the benefits of these PRODUCT FEATURES:

SYSTEM

H.264 / MPEG-4 / Motion JPEG:

Resolutions

Screen Resolution Compressing format

Frame Rate

Image settings

Image snapshot Video Recording Full Screen Viewing Digital Zoom

Audio Instant Messenger

Mobile Phone Live View

Alarm Sending Security

Alarm Buffer

Supported protocols

Simultaneous Connection

Operating conditions

Lens Video Output Local Storage I / O Audio Output Alarm Input Power

Ethernet Wireless

4 resolutions from 1280x1024 to 320x240 via API and configuration web page Higher than 1024 * 720 pixels H.264 / MPEG-4 / Motion JPEG Up to 15 fps at 1280x1024 Up to 30 fps at 640x480 Rotation: Mirror, Flip, Mirror Flip Brightness / Contrast / Saturation Overlay capabilities: time, date, text and privacy image Yes Yes Yes 10x digital Two-way (full / half duplex) with built-in microphone Audio compression: G.711 μ law, a law, and AMR Support MSN Live View

Through 2.5 WAP

FTP Client / SMTP / Network Storage / HTTP Event Password Protection / HTTPS encryption / IP Filter Recording image and audio file pre-and-post disconnection up to 5 sec. Bonjour, TCP/IP, DHCP, PPPoE, ARP, ICMP, FTP, SMTP, DNS, NTP, UPnP, RTSP, RTP, HTTP, TCP, UDP, 3GPP/ISMA RTSP

Up to 10 users

0℃~ 50℃ (32℉ ~ 122℉)

HARDWARE

Changeable CS-mount lens (support Auto Iris) RCA type with BNC adapter Support SD/SDHC card 2 alarm I/O and 1 RS-485 1 2 12V DC, 1A, Max 5W

NETWORK

10 / 100 Base T IEEE 802.11b/g/n (for F7115)

Minimum System Requirement & Product Feature

Page 8

F7110 / F7115 User Manual

Chapter 3. Using IP Camera via Web Browser

3.1Windows Web Browser

1. Open your web browser, and enter the IP address or host name of the IP camera in the Location / Address field of your browser.

Note : If you only want to view the video without accessing Setting screen, enter

“http://<IP>/index2.htm” as your web URL.

2. Use the default account “admin” and default password “admin”.

Note : The default user name “admin” and the password are set at the factory for the

administrator. You can change them in the Account Menu. (Please check “Setting →

Basic → Security → Account”)

3. The monitor image will be displayed in your browser. In the far left side of main configuration are Setting, Client Setting, and Image Setup and PT control. For more details, you can check Chapter 7.2、Chapter 7.3、Chapter 7.4 and Chapter 7.5.

Using IP Camera via Web Browser

Page 9

F7110 / F7115 User Manual

3.2 Mac Web Browser

1. Click the Safari icon, and enter the IP address of the IP camera in the Location / Address field of your browser.

Note : If you only want to view the video without Setting screen

“http://<IP>/index2.htm” as your web URL.

2. Enter the default account “admin” and default password “admin”.

Note : The default user name “admin” and the password are set at the factory for the

administrator. You can change them in the Account Menu (Please check “Setting →

Basic → Security → Account”)

Using IP Camera via Web Browser

Page 10

F7110 / F7115 User Manual

Using IP Camera via Web Browser

Page 11

F7110 / F7115 User Manual

Chapter 4. Setting up Wireless Configuration (Only for F7115 )

The wireless network has to be set up by using cable network connection. After setting the

camera correctly, the wireless function can work without cable network connection. Please

follow the setting process below step by step:

1. Connect IP Camera with Ethernet connection.

2.Go to “Setting → Basic → Network → Wireless,” choose option “On”. You will see

the wireless Setting screen.

3. Then click “Refresh”. All access points (AP) around you will show up.

4. Select the AP you wish to connect.

5. Enter password at active transmit key if you need. If you don't know the setting of the

wireless AP, please ask your network administrator.

Setting up Wireless Configuration

Page 12

F7110 / F7115 User Manual

6. Choose the option of Obtain an IP address automatically (DHCP) and Obtain DNS server address automatically.

7. Otherwise, Choose Use the following IP address and Use the following DNS sever address.

 Use the following IP address: Select this when the fixed IP address is set.

IP address: Enter the IP address of the device. Subnet mask: Enter the subnet mask.  Default gateway: Enter the default gateway.

 Use the following DNS server address: Select this when you set the fixed address as the

IP address of DNS server.

Primary DNS server: Enter the IP address of the primary DNS server. Secondary DNS server: Enter the IP address of the secondary DNS server, if

necessary.

Setting up Wireless Configuration

Page 13

F7110 / F7115 User Manual

Chapter 5. Operating IP Camera via Mobile Phone

5.1 Mobile Phone Viewing

5.1.1 3G Mobile Phone Streaming Viewing

For 3G mobile phone viewing, type “ rtsp://<IP>:<PORT>/video.3gp ” into your 3G

Streaming Link. <IP> is the Public IP address of your IP camera; <PORT> is the RTSP port

of your IP camera (Default value is 554.) Example: rtsp://100.10.10.1:554/video.3gp

Note: You can also use RTSP clients (RealPlayer, VLC, QuickTime Player…etc.) to

view RTSP streaming, just type in “rtsp://<IP>:<PORT>/video.3gp” as the Player URL

5.1.2 2.5G Mobile Phone WAP Viewing

For 2.5G mobile phone viewing, type “http://<IP>/mobile.wml ” into your 2.5G WAP

Browser. <IP> is the Public IP address of your IP camera.

5.1.3 2.5G Mobile Phone Browser Viewing

For 2.5G mobile phone viewing, type “http://<IP>/mobile.htm ” into your 2.5G Web

Browser. <IP> is the Public IP address of your IP camera.

Using IP Camera via Mobile Phone

Page 14

F7110 / F7115 User Manual

5.2 Using IP Camera via iPhone

You can use ZAVIO Web User Interface via iPhone. Please follow the setting process below.

Then you can use ZAVIO Web UI via iPhone.

1. Select Safari function

2. Type IP address in your web link.

3. Type name and password. Default value is admin / admin. Then click Login In

4. The ZAVIO User Interface and live image will show up in the middle of screen.

Note: The image is continuous snapshots, not video. Thus, live image can’t be recorded here.

Using IP Camera via Mobile Phone

Page 15

F7110 / F7115 User Manual

Chapter 6. MSN Messenger

Please follow the following steps to set up the Messenger function.

1. Download free MSN software and create a new MSN account (Camera at home) for Microsoft Live Messenger.

2.Go to “Setting→Basic→Network→Messenger,” set the Messenger to “ON” . Then, login in new account and password (Camera at home).

3. If your router has firewall function, you have to set the Port Range on this setting page in accordance with the one of firewall.

4. Choose the Video Mode, decide the live view image of messenger received from Computer View (MPEG-4) or Mobile View (3GPP).

5. Choose “On” at the option of IP Notification. notification to the users who are allowed.

6. Choose “On” at the option of Privacy. an allow list.

7. Use your account to login in the Messenger software. Then, add the new MSN account (Camera at home )

8. The Camera at home will show up with its Public IP and Private IP if the option of IP Notification is “On”. ( You can enter “Ping” to show up with Public IP and Private IP. )

9. Click on the small camera icon . Then, choose “View a new contact's webcam”.

If you can choose “On” at the privacy option, you can set

If this feature switches On, camera will send IP

MSN Messenger

Page 16

10. The IP Camera will accept your invitation; the live video will show up in the right screen after few seconds.

12. The dialog box will show up with “This application is not part if Window Live Message…….” Tick the box of “Don’t show me this again” and click OK.

F7110 / F7115 User Manual

11. Click Action button and choose Start Control Panel to use control panel.

13. The IP Camera will accept your invitation to start Control Panel.

MSN Messenger

Page 17

14. You can click Camera icon to snapshot then the picture will send to you

immediately.

F7110 / F7115 User Manual

15. You can click paint palette icon showing up with tool bar to set up image. Then, you can use the tool bar to optimize video

Brightness , Contrast , Saturation and Sharpness . After the adjustment of all

setting, you can still click the setting back to the original setting.

to make

16. You can click joystick icon showing up with arrows of different directions. You can click the arrow button of direction to do PT

MSN Messenger

Page 18

F7110 / F7115 User Manual

Chapter 7. Configuration of Main Menu

In the left side of main configuration are Setting, Client setting, Image setting and PT control (appear only when PT/PTZ control enabled). For more details, please check Chapter 7.2、Chapter

7.3、Chapter 7.4.、Chapter 7.5.

In the right side, you can control Live View in your main Browser. The functions include Snapshot, Open digital zoom, Audio, and Video Play.

Full screen

Snapshot

Open digital zoom

Video Play

Configuration of Main Menu

Page 19

F7110 / F7115 User Manual

7.1 Live View

7.1.1 Snapshot

You can capture a still image shot by clicking the camera icon and save it in the operating

computer.

Symbols Meaning

a snapshot window appears after clicking the icon

Save save the picture captured by snapshot into your computer

co er cmput omputer.

Close Return to the view screen

full screen

7.1.2 Digital zoom in / out the image via the monitor window

 Click to display the digital zoom in window.

 Pull the to adjust the digital zoom range, and it will be

showed on the above window.

 Use the left click of your mouse to move to anywhere in the window area.

Configuration of

Main Menu

Page 20

7.1.3 Video play buttons

Symbols Meaning

F7110 / F7115 User Manual

Note: Concerning the recording storage requirement of your hard disk, please refer to

the CHAPTER 10. APPENDIX / B. Storage Requirement Table.

Pause the current video

Play the video

Stop the current video

Record the current video

7.1.4 Audio buttons

Symbols Meaning Note

Speakers turned off

Mute on

Volume control bar

Speakers turned on

Mute off

mean the speakers of your computer are turned on to transmit the sounds from the connected IP camera(s)

mean the speakers of your computer are turned off to transmit the sounds from the connected IP camera(s)

mean you can broadcast to the connected IP camera(s) via the Ethernet using your microphone

mean you can’t broadcast to the connected IP camera(s) via the Ethernet using your microphone

mean you can adjust the sound volume by the control bar

Configuration of

Main Menu

Page 21

F7110 / F7115 User Manual

7.2 Setting

This function is only for the Administrator. Click “Setting” on the home page of web user interface to get into the Basic and Advanced settings menu.

Click Basic folder, there are sub-folders including System, Camera, Network, and Security. Fore more information, you can see Chapter 8.1、Chapter 8.2、Chapter 8.3 and Chapter 8.4.

Click Advanced folder, there are sub-folders including PT control, Preset position, Patrol, FTP Client, SMTP, Network storage, HTTP event, Alarm output, Schedule, Alarm input, Alarm buffer, Motion Detection, Audio Detection, and System Log. Fore more information, please see Chapter 9.

Configuration of

Main Menu

Page 22

F7110 / F7115 User Manual

7.3 Client Setting

This function is only for the client. Click this button to control Mode, View Size, Protocol, and Video Buffer.

7.3.1 Mode

Click the pull-down box to choose video compression mode of LIVE VIEW among H.264, MPEG-4, MJPEG and JPG.

Note: As long as the operating system not able to afford loading under H.264 mode, please

downgrade the mode to MPEG-4 or MJPEG.

7.3.2 View Size

Select the desired view size of image resolution among 1/4X, 1/2X, and 1X.

7.3.3 Protocol

Select the transferring protocol among TCP, UDP, and HTTP.

7.3.4 Video Buffer

Turn the Video Buffer function On / Off. The Video Buffer function makes the streaming more smoothly in unsteady network environment, but might cause a little delay in live viewing.

Configuration of Main Menu

Page 23

F7110 / F7115 User Manual

7.4 Image Setup

The tool bar can be adjusted to optimize video Brightness, Contrast, Saturation Sharpness and Exposure.

7.4.1 Brightness

The value range is 0~99. The higher value the brightness is, the brighter the image is.

7.4.2 Contrast

The value range is 0~99. The contrast is a measure of a display system, defined as the ratio of white to black that the system is capable of producing. The higher value the contrast is, the more delicate of color you can have.

7.4.3 Saturation

The value range is 0~99. The saturation of a color is determined by a combination of light intensity and how much it is distributed across the spectrum of different wavelengths. The higher value the saturation is, the more colorful the image will be.

7.4.4 Sharpness

The value range is 0~99. It applies image processing techniques to adjust the sharpness of live view. However, higher the value is, more the noise is.

7.4.4 Exposure

The value range is 0~99. A value is given to all combinations of camera shutter speed, aperture and gain. The higher value the brightness is, the more exposure the image is.

6.4.5 Default

After the adjustment of all setting, you can still click Default to make the setting back to the original setting.

Configuration of Main Menu

Page 24

7.5 PT Control

7.5.1 Pan / Tilt / Home control buttons

Click the arrow button of the direction you want the IP camera to move.

F7110 / F7115 User Manual

7.5.2 Other camera control functions

Preset: Move the camera toward the preset direction. Patrol: Before you start this function, you need to specify Guard tour settings in the Setting Menu under Advanced / Patrol setting.

Configuration of Main Menu

Page 25

F7110 / F7115 User Manual

Chapter 8. Setting-Basic

Click the Basic folder to display the sub folders including System, Camera, Network, and

Security.

8.1 System

Click the folder of System to display the sub-folders including Information, Date / Time,

Initialize, and Language.

8.1.1 Information

The Information screen provides the product factory information which includes Product

Name, Firmware Version.

Setting-Basic Information

Page 26

8.1.2 Date / Time

The Date/ Time screen displays all options of time setting.

F7110 / F7115 User Manual

 Current date / time: This displays the current date and time of this IP Camera.

 PC clock: This displays the date and time of the monitoring PC clock.  Date / Time format: You can click the pull down box to select different time display

formats.

Note: If you would like the Date / Time information shows on the Live View screen,

please check “Setting → Basic → Camera → General → Overlay → Text overlay →

Date / Time ” to execute the setting.

 Adjust: You can select one of those four adjusting modes for your IP Camera.

 Keep current setting: Select this mode to keep the current date and time of this IP

Camera.

 Synchronize: Select this mode to keep the date and time of this IP Camera is the same

as the monitoring PC.

 Manual setting: Select this mode to adjust manually the date and time of this IP

Camera.

 Synchronize with NTP: Specify the NTP server name and the Refresh Interval to

synchronize the date and time of this IP Camera with those of the time server, known as the NTP server.

Setting-Basic Date/Time

Page 27

F7110 / F7115 User Manual

 Time Zone: Select the Time Zone format of Greenwich Mean Time among different

cities. The time display will be the same as the current date / time option.

 Daylight Saving Time: There are two modes to choose for setting up daylight saving

time.

 By Date: Set the start and end time by select month, day, hour, and minute.  By Week Number: Set the start and end time by select month, week, hour, and

minute.

Note: The NTP server (Network Time Protocol) is the time server which is an Internet

standard protocol built on the top of TCP / IP. This assures accurate synchronization to

the millisecond of computer clock times in a network of computers.

8.1.3 Initialize

 Reboot: Click this button to reboot this IP Camera. A confirmation dialogue will appear and then click “OK” to execute. It takes one minute to complete the reboot process.

 Factory Default: Click this button to recover this IP Camera to the factory default setting. A confirmation dialogue will appear and then click “OK” to execute. The network indicator on this IP Camera will start to blink. This IP Camera will reboot automatically after completing adjustments to the default setting. Don't turn off this IP Camera until the device reboots.

 Backup Setting: You can save the setting data of this IP Camera into a file. Click “Save”

Setting-Basic Initialize

Page 28

F7110 / F7115 User Manual

and follow the instructions on the browser to save the setting data file to the location you specified.

 Restore Setting: Download the saved setting data of this IP Camera. Click “Browse” and select saved file. Click “OK” and this IP Camera is adjusted according to the loaded data and then restarted.

 Firmware Update: Update the device software. Click “Browse” and select the file for updating. A confirmation dialogue will appear. Click “OK” to start. This IP Camera will reboot upon completion.

Note: When updating the firmware version, please use the file specific for the model.

Otherwise, some problems may occur. Unless the updating completed, please don’t

turn off the power or disconnect the network.

8.1.4 Language

 Upload Language Pack: Clicking “Browse” and selecting the file for updating, the present language display of WEB User Interface could be changed. A confirmation dialogue will appear. Click “OK”, then the update will be applied immediately. The default language is “English.”

Setting-Basic Language

Page 29

F7110 / F7115 User Manual

8.2 Camera

Click the folder of Camera to display the sub folders including General, H.264, MPEG-4,

MJPEG, 3GPP, and Advanced.

8.2.1 General

 RTSP: The default value is 554. If the IP Cameras connected with router and installed

outside are over 2 sets and all of them need support RTSP, please fill some value in the blank space in the range from 1024 to 65535.

 RTP Unicast streaming: The default value of port range is 5000 ~ 7999 and can be

changed from 1024 to 65535.

Note: Under Unicast streaming mode, streaming video is delivered from the camera to

a single client device.

 Image Rotated: Select the screen display “flip”, “mirror”, or “flip + mirror.”

 Audio Codec: Select one audio codec among G.711 U-law / G.711 A-law / AMR Audio /

Off.

G.711 U-law : one codec for “Computer Audio”, used in North America & Japan

areas.

G.711 A-law : another codec for “Computer Audio”, used in Europe and the rest of the

world.

AMR Audio: an audio codec of the third generation communication for MOBIL

PHONE. While the option selected, your mobile phone will receive the audio file

Setting-Basic Camera

Page 30

F7110 / F7115 User Manual

from IP Camera. And you can choose the bit rate from 4.75k to 12.2k. However, the usage of this codec will cause frame-rate decreasing.

Off: Select Off, audio file won’t be transmitted by IP CAM.

 Audio mode: You can select Full duplex or Half duplex.

Full duplex: Select it for simultaneous communication in both direction between the

connected administrator and IP CAM. It means both parties can speak and be heard at the same time.

Half duplex: Select it for communication in both directions, but only one direction at

a time (not simultaneously). It means one party begins receiving a signal, it must wait for the transmitter to stop transmitting, before replying. Therefore, once one party speak, he can’t hear any voice from the other party, just like the communication by radio set.

 Video clip format: Select RECORDING compression format H.264 or MPEG-4.

MPEG-4: MPEG-4 has the advantage of sending a lower volume of date per time

unit across the network (bit-rate) compared to Motion JPEG and therefore provides a relatively high image quality at a lower bit-rate (bandwidth usage).

H.264: H.264 provides higher compression rate than MPEG-4. Thus, H.264 can

decrease the bandwidth usage and further apply on 3G. However, H.264 will occupy more system resources than MPEG-4. As long as the operating system appears operating difficulties under H.264 format, please change to select MPEG-4.

 Analog Video Output: Analog video output is for fast and easy installation. The default is On and the mode of live view of Client Setting page will be fixed in H.264. If off chosen, the string option will appear H.264, MPEG-4, and MJPEG.

 IR Threshold: Select LED light On, Off, or Auto.

On: Select On will led always work. Off: Select off will disable led. Auto: Select Auto will appear two thresholds, Bright and Dark. You can adjust them

for IR Auto-On and Auto-Off respectively. Bright value higher, IR auto-off more easily in the bright environment will be. Dark value higher, led auto-on more easily in the dark environment will be. Bright Value is ranges from 0 to 70, and Dark Value is from 30 to 100. The interval value between both is at least 30. The default value for B5110 is 50 and 85.

 LED Indicator: Enable/disable LED indicator.

On: Select On to enable LED indicator. Off: Select off to disable LED indicator.

 Overlay:

Text Overlay: Some information can be showed on the display screen, such as Date /

Time and user-defined text. And the background color can be chosen.

Privacy Mask: A specific area of the video image can be covered.

Setting-Basic

Camera

Page 31

8.2.2 H.264

F7110 / F7115 User Manual

 Viewer authentication:

On: If the viewer authentication is On, the users will be requested to key-in username

and password when using QuickTime Player…etc. to have live viewing.

Off: If the viewer authentication is Off, you can have live viewing on computer by

QuickTime Player…etc. after entering “rtsp://ip:port/video.h264” on the URL column directly.

 Multicasting streaming (if it’s on):

Multicast Address: The multicast server address will appear automatically. Video / Audio Port: Specify the transmission port number of the video data, from

1024 to 65535.

Time to Live: Set the maximum TTL that multicast can pass through.

Note: Time To Live option determines the maximum length of time (measure as the

number of network routers that can be passed before data arrives at its destination or

is dropped) within which a multicast packet must reach its destination.

 Image Size: Specify the image size when the network camera transmits. Choose one among 1280 x 1024, 1280 x 720, 640 x 480, and 320 x 240.

 Frame Rate: Set the frame rate of H.264 image. Choose one value among 2, 3, 4, 5, 7, 10, 15, 20, 25, and 30 fps. The unit “fps” stands for “frames per second”.

Note: The frame rate is up to 15 fps at 1280x1024, and up to 30 fps at 640x480.

However, if you would like choose frame rate over 15 fps, the IMAGE SIZE of

H.264/MPEG-4/MJPEG setting page has to been selected 320x240 or 640x480 at the

same time.

Setting-Basic

Camera

Page 32

F7110 / F7115 User Manual

 Quality:

 Auto: The quality and bitrate will be adjusted automatically according to the frame

rate.

 Fixed Quality: Select the value of quality among Medium, Good, Delicate and

Excellent.

 Fixed Bitrate: Set the bitrate of H.264 image transmission for a line. Select one among

64Kbps, 128Kbps, 256Kbps, 384Kbps, 512Kbps, 768Kbps, 1Mbps, 1.5 Mbps, 2 Mbps, 3 Mbps, 4 Mbps, 5 Mbps, and 6 Mbps.

Note: Concerning how to select the suitable image quality for Fixed Quality or Fixed

Bitrate, please refer to the CHAPTER 10. APPENDIX / A. Frame-rate & Bitrate Table.

 IP interval: It’s the ratio of i-frame & p-frame. Select one among 1, 5, 10, 15, 30, 60, and

120. The ratio smaller, the streaming smoother.

Note: The IP interval value means a ratio of “ P-frame / I-frame “ in a certain section of

frame sequences. The ratio lower, the live view clear. However, live view will lag if the

bandwidth isn’t big enough. In this situation, you have to choose another bigger IP interval

value to solve the problem.

Note: If Video clip format of General Menu, which is for recording compression, is chosen

H.264, the IP interval option will appear “Auto” automatically and can’t select. The limit is

for avoiding damaging the recording quality of 5 seconds temporary-saved video recorded

on FTP server.

8.2.3 MPEG-4

Setting-Basic Camera

Page 33

F7110 / F7115 User Manual

 Viewer authentication:

On: If the viewer authentication is On, the users will be requested to key-in username

and password when using QuickTime Player…etc. to have live viewing.

Off: If the viewer authentication is Off, you can have live viewing on computer by

QuickTime Player…etc. after entering “rtsp://ip:port/video.mp4” on the URL column directly.

 Multicasting streaming (if it’s on):

Multicast Address: Specify the multicast server address. Video / Audio Port: Specify the transmission port number of the video data, from

1024 to 65535.

Time to Live: Set the maximum TTL that multicast can pass through.

Note: Time To Live option determines the maximum length of time (measure as the

number of network routers that can be passed before data arrives at its destination or

is dropped) within which a multicast packet must reach its destination.

 Image Size: Specify the image size when the network camera transmits. Choose one among 1280 x 1024, 1280 x 720, 640 x 480, and 320 x 240.

 Frame Rate: Set the frame rate of the MPEG-4 image. Choose one from 1, 2, 3, 4, 5, 7, 10, 15, 20, 25, and 30 fps. The unit “fps” stands for “frames per second.”

Note: The frame rate is up to 15 fps at 1280x1024, and up to 30 fps at 640x480.

However, if you would like choose frame rate over 15 fps, the IMAGE SIZE of

H.264/MPEG-4/MJPEG setting page has to been selected 320x240 or 640x480 at the

same time.

 Quality:

 Auto: The quality and bitrate will be adjusted automatically according to the frame

rate.

 Fixed Quality: Select the value of quality among Medium, Good, Delicate and

Excellent.

 Fixed Bitrate: Set the bitrate of MPEG-4 image transmission for a line. You can select

one value among 64Kbps, 128Kbps, 256Kbps, 384Kbps, 512Kbps, 768Kbps, 1Mbps,

1.5 Mbps, 2 Mbps, 3 Mbps, 4 Mbps, 5 Mbps, and 6 Mbps.

Note: Concerning how to select the suitable image quality for Fixed Quality or Fixed

Bitrate, please refer to the CHAPTER 10. APPENDIX / A. Frame-rate & Bitrate Table.

 IP interval: It’s the ratio of i-frame & p-frame. You can select one among 1, 5, 10, 15, 30, 60, and 120. The ratio smaller, the streaming smoother.

Note: The IP interval value means a ratio of “ P-frame / I-frame “ in a certain section of

frame sequences. The ratio lower, the live view clear. However, live view will lag if the

bandwidth isn’t big enough. In this situation, you have to choose another bigger IP interval

Setting-Basic

Camera

Page 34

F7110 / F7115 User Manual

value to solve the problem.

Note: If Video clip format of General Menu, which is for recording compression, is chosen

MPEG-4, the IP interval option will appear “Auto” automatically and can’t select. The limit

is for avoiding damaging the recording quality of 5 seconds temporary-saved video

recorded on FTP server.

8.2.4 MJPEG

 Viewer authentication:

On: If the viewer authentication is On, the users will be requested to key-in username

and password when using QuickTime Player…etc. to have live viewing.

Off: If the viewer authentication is Off, you can have live viewing on computer by

QuickTime Player…etc. after entering “rtsp://ip:port/video.mjpg” on the URL column directly.

 Multicasting streaming (if it’s on):

Multicast Address : Specify the multicast server address. Video / Audio Port: Specify the transmission port number of the video data, from

1024 to 65535.

Time to Live: Set the maximum TTL that multicast can pass through.

Note: Time To Live option determines the maximum length of time (measure as the

number of network routers that can be passed before data arrives at its destination or

is dropped) within which a multicast packet must reach its destination.

 Image Size: Specify the image size when the network camera transmits. Choose among 1280 x 1024, 1280 x 720, 640 x 480, and 320 x 240.

 Frame Rate: Set the frame rate of the MJPEG image. Choose one among 1, 2, 3, 4, 5, 7,

Setting-Basic

Camera

Page 35

F7110 / F7115 User Manual

10, 15, 20, 25, and 30 fps. The unit “fps” stands for “frames per second”.

Note: The frame rate is up to 15 fps at 1280x1024, and up to 30 fps at 640x480.

However, if you would like choose frame rate over 15 fps, the IMAGE SIZE of

H.264/MPEG-4/MJPEG setting page has to been selected 320x240 or 640x480 at the

same time.

 Quality:

 Auto: The quality and bit rate will be adjusted automatically according to the frame

rate.

 Fixed Quality: Select the value of quality among Medium, Good, Delicate and

Excellent.

 Fixed Bitrate: Set the bitrate of MJPEG image transmission for a line. You can select

one among 64Kbps, 128Kbps, 256Kbps, 384Kbps, 512Kbps, 768Kbps, 1Mbps, 1.5 Mbps, 2 Mbps, 3 Mbps, 4 Mbps, 5 Mbps, and 6 Mbps.

Note: Concerning how to select the suitable image quality for Fixed Quality or Fixed

Bitrate, please refer to the CHAPTER 10. APPENDIX / A. Frame-rate & Bitrate Table.

8.2.5 3GPP

 Viewer authentication:

On: If the viewer authentication is On, the users will be requested to key-in username

and password when using QuickTime Player…etc. to have live viewing.

Off: If the viewer authentication is Off, you can have live viewing on computer by

QuickTime Player…etc. after entering “rtsp://ip:port/video.3gp” on the URL column directly.

 Image Size: Image size for 3GPP is 160 x 120.

 Frame Rate: Set the frame rate of the 3GPP image. Choose one between 5 or 10 fps. The

Setting-Basic

Camera

Page 36

F7110 / F7115 User Manual

unit “fps” stands for “frames per second.”

 Quality:

 Auto: The quality and bit rate will be adjusted automatically according to the frame

rate.

 Fixed Quality: This item here can’t be selected.  Fixed Bitrate: Set the bitrate of 3GPP image transmission for a line. You can select

one among 64Kbps, 128Kbps, 256Kbps, 384Kbps, 512Kbps, 768Kbps, 1Mbps, 1.5 Mbps, 2 Mbps, 3 Mbps, 4 Mbps, 5 Mbps, and 6 Mbps.

 IP interval: It’s the ratio of i-frame & p-frame. You can select one among 1, 5, 10, 15, 30, 60, and 120. The ratio smaller, the streaming smoother.

Note: The IP interval value means a RATIO of “ P-frame / I-frame “ in a certain section of

frame sequences. The ratio lower, the live view clear. However, live view will lag if the

bandwidth isn’t big enough. In this situation, you have to choose another bigger IP interval

value to solve the problem.

8.2.6 Advanced

 White Balance: Choose the white balance among Auto, Florescent, Incandescent and Black & White.

 Lighting: The default setting of lighting environment is Auto. However, you may also

choose 50 or 60 Hz upon the lighting environment of your country.

Setting-Basic

Camera

Page 37

 Exposure mode: Choose Auto or Manual upon the capture environment.

 Auto: Choose Auto and you have 3 options to adjust the exposure condition.

 Back Light Compensate: Click it on and it helps avoid problems in

situations where the main subject ends up being too dark, such as when shooting people or other subjects in front of a bright background.

 Slow Shutter: Click it on and the range of shutter speed will be from 1/5 to

1/120 sec. It will adjust the shutter speed automatically and helpful to capture the clear image when shooting in a dark place.

 High Speed Mode: Click it on and the shutter speed will be close 1/120 sec. as far as

possible to help to capture the motion image of sports or high-speed phenomena.

 Manual : Choose Manual and you can select options, such as Shutter Speed, Gain,

and Bad Pixel Compensate.

F7110 / F7115 User Manual

 Shutter Speed: The default value is 1/30 sec. and you can select the value

among 1/4, 1/6, 1/12, 1/30, 1/60, and 1/120 sec.

 Gain: The default value is 2 and you can select the value among 0~9. The

value of the gain will influence the brightness of the image. The more the value is , the brighter the image is. However, the higher gain value might cause more noise.

 Iris: Choose Auto or Open upon the capture environment.

 Auto: Choose Auto to enable auto Iris.  Open: Choose Open to enable maximum aperture.  Calibrate: Click Calibrate to adjust auto Iris lens. The whole process will continue

2~3 minutes.

Note: Click Calibrate to adjust your auto Iris lens when you change a new one in order to gain best

image quality.

Setting-Basic

Camera

Page 38

F7110 / F7115 User Manual

8.2.7 PLAYBACK

Clicking the button of “Open files” and select the video file recorded previous, you can look

for the desired image. Besides, you can still have the live view in the screen. The function of each button is as below illustration:

Mirror/ Flip

Snapshot

Full Screen

Pause

Stop

Open files

Previous track

Next track

Mute on / Mute off

Vol ume

Open digital zoom

Setting-Basic Camera

Page 39

F7110 / F7115 User Manual

8.3 Network

Click the folder of Network to display the sub folders including Information, PPPoE,

DDNS, UPnP, Bonjour, IP Notification, Wireless and Messenger.

8.3.1 Information

Display the MAC address of the device.

 Obtain an IP address automatically (DHCP): If a DHCP server is installed on the network, to select this while the IP address is assigned by the DHCP server.

 Obtain DNS server address automatically: Select this to obtain the address of DNS server automatically.

Setting-Basic Network

Page 40

F7110 / F7115 User Manual

Use the following IP address: Select this option when the fixed IP address is set.

IP address: Enter the IP address of the device. Subnet mask: Enter the subnet mask.  Default gateway: Enter the default gateway.

 Use the following DNS server address: Select this when you set the fixed address as the

IP address of DNS server.

Primary DNS server: Enter the IP address of the primary DNS server. Secondary DNS server: Enter the IP address of the secondary DNS server, if

necessary.

 HTTP port number: Select 80 in general situations. If you want to use a port number other than 80, select the text box and enter a port number between 1024 and 65535.

 When you have set the HTTP port number to a number other than 80 on the Network

Setting screen in the Setup Program, access the device by typing the IP address of the device on the web browser as follows: Example: when HTTP port number is set to 2000 http://192.168.1.100:2000/

Note: The IP Camera needs to be rebooted after it finishes changing the network setting

completely.

Note: If you connect the IP Camera with your computer directly, the default network domain

of camera is 192.168.1.xx

8.3.2 PPPoE (Point-to-Point Protocol over Ethernet)

If your ISP provides Dynamic IP with authentication by username and password, type all PPPoE information in this part. When using the PPPoE function, you need to turn on the DDNS or IP Notification function at same time.

Setting-Basic Network

Page 41

F7110 / F7115 User Manual

 IP address: The IP address obtained at the PPPoE connecting with network.

 User ID: Enter the user ID for authentication necessary for PPPoE connections. Type it

up to 64 characters.

 Password: Enter the password for authentication necessary for PPPoE connections. Type it up to 32 characters.

 Re-type password: Re-type the password to confirm.

 Obtain DNS server address automatically: Select this to obtain the address of DNS

server automatically.

 Use the following DNS server address: Select this when you set the fixed address as the IP address of DNS server.

 Primary DNS server: Enter the IP address of the primary DNS server.  Secondary DNS server: Enter the IP address of the secondary DNS server.

Note : 1. PPPoE (Point-to-Point Protocol over Ethernet): PPPoE is a network protocol

for encapsulating Point-to-Point Protocol frames insider Ethernet frames. PPPoE

connection is used mainly with ADSL service where individual users connect to the

ADSL transceiver (modem) over Ethernet work. It also widely used in XDSL (digital

Setting-Basic Network

affiliate line such as ADSL, VDSL or SDSL)

2. The IP Camera needs to be rebooted after it finishes changing the network

completely.

3. The IP Camera with Intelligent IP Installer can’t be founded after turning on the

PPPoE and reboot.

Page 42

F7110 / F7115 User Manual

8.3.3 DDNS (Dynamic DNS)

DDNS is a system which allows the domain name data held in a name server to be updated in real time. The most common use for DDNS is allowing an internet domain name to be assigned to a computer with a varying / dynamic IP Address. This makes it possible for other sites on the internet to establish connection to the machine without needing to track the IP Address themselves.

 Server name: Choose the DDNS Server from the list.

 User ID: Enter the user ID for authentication necessary for DDNS connections. Type it up

to 64 characters.

 Password: Enter the password for authentication necessary for DDNS connections. Type it up to 32 characters.

 Re-type password: Re-type the password to confirm.

 Host name: Enter the host name that is registered to the DDNS server.

 Periodical Update: Update your DDNS information periodically.

Setting-Basic Network

Page 43

F7110 / F7115 User Manual

Note : How to apply DDNS username and Host name?? You can apply DDNS

username and Host name by the following steps:

1. Login http://www.dyndns.org, click the Creat Account

2. Input all information and follow step by step with DynDNS

Setting-Basic Network

Page 44

F7110 / F7115 User Manual

3. Login with new account and click Account → My Hosts → Add Host Services

4. Type domain in the Hostname field and select sub-domain

Setting-Basic Network

Page 45

F7110 / F7115 User Manual

5. After type information, check your DDNS service.

6. Type your DDNS User ID, Password and Host name in Setting → Network → DDNS. After completing setting, reboot IP Camera.

Setting-Basic Network

Page 46

F7110 / F7115 User Manual

8.3.4 UPnP (Universal Plug and Play)

If you have a Router to access to internet and the Router supports UPnP IGD function, you need to turn on the UPnP Port Forwarding function.

 HTTP port: Enter the HTTP port number and default HTTP port is 80.

 SSL port: Enter the SSL port number and default SSL port is 443.

 RTSP port: Enter the RTSP port, default value is 554 for computer view.

Note : UPnP (Universal Plug and Play): UPnP is a set of computer network protocol. It

allows devices to connect seamlessly and simplify the implementation of networks in the

home and corporate environments.

Setting-Basic Network

Page 47

F7110 / F7115 User Manual

8.3.5 Bonjour

Bonjour, also known as zero-configuration networking, enables automatic discovery of computers, devices, and services on IP networks. Bonjour uses industry standard IP protocols to allow devices to automatically discover each other without the need to enter IP addresses or configure DNS servers.

 Device Name: Enter Device Name you wish.

Note: How to use Bonjour in your Windows Browser UI? Please check the link below:

http://www.apple.com/support/downloads/bonjourforwindows.html

Setting-Basic Network

Page 48

F7110 / F7115 User Manual

8.3.6 IP Notification

When network notify type is set to “ON”, you can send an e-mail notification of the completion of

the network setting.

 Notify Type: You can select the notify type among DHCP, Static IP, and PPPoE.

 SMTP Server Name: Type the SMTP server name up to 64 characters, or the IP address

of the SMTP server.

 SMTP Server Port: You can set port number from 1~65535 according to your mail server. The default value is 25.

Security setting: Tick SSL box if the mail server you use has security restriction.

Note: If you use g-mail as your mail server, you should set 25 as your port number and

tick SSL box.

 Authentication: Select the authentication required when you send an email.

Off: Select if no authentication is necessary when an email is sent.  On: When authentication is necessary an e-mail is sent, there are SMTP, POP before

SMTP or both three options.

 SMTP: Select if SMTP authentication is necessary when an e-mail is sent.  POP before SMTP: Select if POP before SMTP authentication is necessary when an

e-mail is sent.

 POP server name: It is necessary when the POP before SMTP is selected in

Authentication. Type the POP (receiving mail) server name up to 64 characters, or

type the IP address of the POP server. This setting is necessary when the SMTP server which sends e-mails performs authentication using the POP user account.

Setting-Basic

Network

Page 49

F7110 / F7115 User Manual

 User name, Password: Type the user name and Password of the user who has the

mail account. This setting is necessary when the SMTP server which sends e-mails performs authentication.

 Recipient e-mail address: Type the recipient e-Mail address up to 64 characters. You can specify up to three recipient E-mail addresses.

 Administrator e-mail address: Type the Administrator e-Mail address up to 64 characters. This address is used for reply mail and sending system messages from the SMTP server.

 Subject: Type the subject/title of the e-Mail up to 64 characters. With respect to mail which is sent according to the IP notification.

 Message: Type the text of the E-mail up to 384 characters. Default value provides network information including IP, Port, MAC, Model, Firmware Version and Web Version.

8.3.7 Wireless (Only for F7115)

The wireless network has to be set up by using cable network connection. After setting the camera correctly, the wireless function can work with cable network connection. Wireless settings must be the same as the access point or ad-hoc device. When changing the settings they should always be made first in the camera and then in the wireless access point. This ensures that the camera is always accessible when making changes.

Setting-Basic Network

Page 50

F7110 / F7115 User Manual

 Status of Wireless Network

This list is the result of network scan. The network is currently linked to will be shown in blue. The following information is provided.

ESSID - The name of a wireless network (or ad-hoc device). If the same name occurs

several times this means that several access points for that network were found. The camera cannot be configured to only associate with one particular access point.

Mode - Shows if the network type is Master (access point or router) or Ad-Hoc

(another client).

Security - Shows which type of security the network uses. See below for the security

types supported by the camera.

Channel - Shows the wireless channel currently in use. Signal strength - Shows the signal strength. Bit rate - Shows the bit rate in Megabit/s. This can only be shown for the access point

currently in use. Note that the bit rate shown is the current rate, and that this value may vary over time.

 Wireless Setting

These settings control how the camera interacts with the wireless network. It is also possible to enable wireless encryption apart from identifying the wireless network.

 IP Address – This displays blank, 0.0.0.0 or IP Address. When it is blank, the camera

doesn’t establish physical link with access point yet. The 0.0.0.0 means that physical link was established but trying to get IP address. When it displays IP address, then user can use wireless network.

 ESSID (ESSID is sometimes written as SSID.) - This is the name of the wireless

network the camera is configured for. The field accepts up to 32 alphanumeric characters. The name must be exactly the same as that used in the wireless access point or the connection will not be established.

 Leaving this field blank means the camera will attempt to access the nearest open

network.

Mode - Setting this to Managed means the camera will attempt to access the nearest

open access point. The Ad-hoc option allows the camera to connect to other wireless devices clients.

Note : 1. WPA-/WPA2-PSK (Wi-Fi Protected Access - Pre-Shared Key) the camera uses

a pre-shared key (PSK) to initiate WPA security. The pre-shared key is entered on the

access point and on each device on the wireless network. The key can be entered either

as Manual hex, as 64 hexadecimal (0-9, A-F) characters, or as a Passphrase, using 8 to

63 ASCII characters. The access point keeps out unauthorized users by requiring the

key to communicate.

2. WEP (Wired Equivalent Protection) the original security standard used in wireless

networks that provides a minimal level of security that can deter minor trespasses. The

Setting-Basic

Network

Page 51

F7110 / F7115 User Manual

administrator can select the key length among 64 or 128 bits. 64bits is the default

setting.

8.3.8 WPS

WPS (Wi-Fi Protected Setup) also known as a standard for easy and secure establishment of a wireless home network.

 Status of WPS

This list is the result of network scan that only provide wireless AP with WPS function. The network is currently linked to will be shown in blue.

 Configuration Method

PBC – Select and click Start to start WPS configuration.

PIN – Select and click Generate new PIN to generate a new PIN code and then you

can click Start to start WPS configuration.

Setting-Basic Network

Page 52

F7110 / F7115 User Manual

8.3.9 Messenger

Messenger function provide an easy-connect feature. User can easy to know what camera’s private and public IP address is.

 Protocol: support MSN only.

 Login Account: Camera will use this account to login MSN server. This MSN account

should be applied form http://www.msn.com.

 Password: password for this msn account.

 Re-type password: re-type password to double confirm.

 Alias: This alias will display on MSN like the following which display in red frame.

 Port range: Camera will select one port from this port range for video transmission.

Setting-Basic Network

Page 53

F7110 / F7115 User Manual

 Video Mode: You can choose to receive video streaming from Computer view (MPEG-4)

or Mobile view (3GPP).

 IP Notification: Switch the IP notification On / Off. If this feature switches On, camera will send IP notification to the users who are allowed.

 Privacy: Switch privacy On / Off. When privacy turns on, only those users in allow list can access the camera.

 User: Input to this blank to edit allow list.

 Allow list: When privacy turns on, only those users in allow list can access the camera.

Setting-Basic Network

Page 54

F7110 / F7115 User Manual

8.4 Security

Click the folder of Security to display the sub folders including Account and HTTPS.

8.4.1 Account

The device fault account and password setting is “admin / admin”. That means everyone who knows IP address can access the device including all configuration. It is necessary to assign a password if the device is intended to be accessed by others.

 User name: Set a user name between 4-16 characters.

 Password: Set a password between 4-16 characters.

 Re-type Password: Re-type the password to confirm.

 Viewer Mode: Set the user mode among Admin, Operator, and Viewer. Different viewer

mode has different limits of authority.

The Admin mode has all authority of configuration. The Operator mode can not only view the Live View but also control the PTZ (apply

in speed dome).

The Viewer mode only can view the Live View.

 Viewer Authentication: Select On, allows any viewer direct access to Live View. Select

Off, allow admin, operator, or viewer access to Live View.

Setting-Basic Security

Page 55

F7110 / F7115 User Manual

8.4.2 HTTPS

HTTPS is a URL scheme used to indicate a secure HTTP connection. It is syntactically

identical to the http:// scheme normally used for accessing resources using HTTP. Using an https: //URL/ with a different default TCP port (443) and an additional encryption / authentication layer between the HTTP and TCP. You can use the IP camera through HTTPS easily by using https:// instead of http://.

 Create & Install: Create a self-signed certificate for HTTPS to recognize.

 Installed Certificate: Display or remove the properties of the installed certificate.

 HTTPS Connection Policy: Set HTTPS connection policy for different level of users.

 To use the HTTPS encryption, please set up “Create self-signed certificate” for the first

time you use the HTTPS function, and then set up the connection policy for different users.

Note: When enable HTTPS with RTSP on mode, the IP Camera only protect the setting such

as username and password and do not protect video and audio. When enable HTTPS with

RTSP off mode, the IP Camera will protect all setting including video and audio.

Setting-Basic

Security

Page 56

F7110 / F7115 User Manual

8.4.3 IP Filter

IP Filter provides the function of controlling the range of IP address, similar with firewall service.

 IP filter: Select if you would like to have IP filter function.

 Allow range: The default range is from 0.0.0.0 to 255.255.255.255. Enter the “Start IP

address” and “End IP address” in the range, then you can add a new allow range in allow range list.

 Allow range list: Except the default range 0.0.0.0~255.255.255.255, the list allows to

add four more sets of allow range at most.

 Deny range: You can define the deny range by entering “Start IP address” and “End IP

address”

 Deny range list: You can define not more than five sets of deny range in the list.

Setting-Basic Security

Page 57

F7110 / F7115 User Manual

Chapter 9. Setting-Advanced

Click the folder of Advanced to display the sub folders including PTZ control, Preset position,

Patrol, FTP client, SMTP, Network storage, HTTP event, Alarm output, Schedule, Alarm

input, Alarm buffer, Motion detection, Audio detection, and System Log.

9.1 PTZ Control

In this section, it provides Pan, Tilt, Auto Pan speed control setting.

9.1.1 Setting

 Pan Speed: Use it to move bar from 0 to 100.  Tilt Speed: Use it to move bar from 0 to 100.  Auto Pan Speed: Use it to move bar from 0 to 100.  Protocol: Select protocol of your pan/tilt motor.  Baud Rate: baud rate of your pan/tilt motor.  Address: Select address of your pan/tilt motor.

Setting-Advanced

Page 58

F7110 / F7115 User Manual

9.2 Preset Position

In this section, up to 32 Pan and Tilt positions can be saved, as well as the home position, which the device faces to when the power is turned on.

9.2.1 Setting

 Set: Use it to save the camera position to a preset number.

Carry out the following steps.

 Move the camera to the position to be saved while you are checking the image with the

main console.

 Write the preset position name in Preset Pos. Name text box.  Click the SET. The camera position is saved.  If want to set this position as home position, click Home option on. Click the SET. The

camera position is saved as home position.

Note： Setting the new Home position will replace previous Home position.

 Reset: When writing the preset position name in Preset Pos. Name text box, press Reset to

clean filed words.

 Delete All: Be careful! When pressing Delete All, all Preset Position information will be

deleted.

Setting-Advanced Present Position

Page 59

F7110 / F7115 User Manual

 Delete: Select a preset number from 1 to 32 in the list box. Use it to delete specific number

preset position setting.

9.2.2 Alarm Sending

 Alarm

 Motion detection: Click it on for using Motion detection function as a sensor. You

can set motion detection function at the motion detection function screen.

Note: You can set motion detection at motion detection screen. (Please go “Setting →

Advanced →Motion detection → Setting”) For more details, you can check Chapter 9.12.

 Audio detection: Click it on for using Audio detection function as a sensor. You can

set audio detection function at the audio detection function screen.

Note: You can set audio detection at audio detection screen. (Please go “Setting →

Advanced →Audio detection → Setting”) For more details, you can check Chapter 9.13.

 Network Link Down: Click it on to use alarm buffer function for recording audio file

in the IP CAM before and after disconnected network.

Setting-Advanced

Present Position

Page 60

F7110 / F7115 User Manual

Note: You can set alarm buffer at alarm buffer screen. (Please go “Setting → Advanced →

Alarm buffer → Setting”) For more details, you can check Chapter 9.11.

 Alarm Input: Select the connected alarm. Sensor input1: The external sensor which

is connected to sensor input1 of the alarm input.

Note: You can set the alarm input function at alarm input screen. (Please go “Setting →

Advanced → Alarm input → Setting”). For more details, you can check Chapter 9.10.

 Effective period: Set the period when the periodical sending is effective.

Always: The periodical sending is always effective. Schedule: You can specify the period when the periodical sending is effective in the

Schedule setting in the other section.

Note: You can set schedule function at schedule screen. (Please go “Setting → Advanced

→ Schedule → Setting”) For more details, you can check Chapter 9.9.

Setting-Advanced Present Position

Page 61

F7110 / F7115 User Manual

9.3 Patrol

There are four patrol tours to set for composing different preset positions. Each one lists up to 8 positions which can be programmed, and the camera moves to the programmed positions sequentially. The camera stops when it moves to the last preset position.

 Tour name: Rename the tour name.

 Tour position

 Order: There are 8 orders to select for camera directions.  Select Pos.: There are up to 32 preset positions to choose for each order.  Waiting time: When you click Recall, the camera moves to position of the selected preset

number.

 Clear: When setting specific preset number position to tour, click Clear to clear this

direction information.

 Clear All: Be careful! When you click Clear All, it will clear this tour all information out.  Set: Use it to save the camera position to a preset number.

 Set as default tour: Click it on to set this tour as default.

 Tour Start: To click Tour Start, and the camera moves on patrol tour.  Tour Stop: While the camera moves on patrol tour, click Tour Stop to stop the patrol

tour.

 Carry out the following steps:

1. Click Order to choose one of eight orders.

2. Click Select Pos. to set the preset position.

3. Click the SET. The tour position is saved.

4. Follow the steps to set the other orders.

5. Click the OK to save the tour.

Setting-Advanced Patrol

Page 62

F7110 / F7115 User Manual

9.4 FTP Client

Use this menu to set up for capturing and sending a image or video clip to an FTP server. By using FTP client function, you can send files which has been shot and recorded linked with the external sensor input or with the built-in motion detection function to FTP server. FTP client setting menu is composed of two tabs, General, Alarm sending and Periodical

sending.

9.4.1 General

Select On when you use FTP function. The FTP client Setting screen appears. Select Off, when you do not wish to use the FTP client function.

Note: The frame rate and operability on the main viewer may decrease while a file is

being transmitted by the FTP client function.

 FTP server name: Type the FTP server name to upload still images up to 64 characters,

or the IP address of the FTP server.

 User name: Type the user name for the FTP server.

 Password: Type the password for the FTP server.

 Retype password: To confirm the password, type the same characters as you typed in the

Password box.

 Passive mode: Set whether you use the passive mode of FTP server or not when

connecting to FTP server. Select On to connect to FTP server using the passive mode.

Setting-Advanced FTP Client

Page 63

F7110 / F7115 User Manual

 Attached file type: You can choose snapshot or video clip for alarm sending. Select

“Snapshot,” one snapshot will be transmitted to the specified FTP server while motion detection / audio detection / alarm input triggered. Select “Video clip,” one 5-seconds video clip will be transmitted.

 Te st : After setting the FTP server information, you can tick the test key to test if the

connection between IP CAM and FTP server works.

9.4.2 Alarm sending

Set to forward a snapshot or video clip file to the specified FTP server linked with the alarm detection by the external sensor input or by the built-in motion detection function. Select On to send the file to FTP server linked with the alarm detection.

 Remote Path: Type the path to the destination in FTP server up to 64 characters.

 Image File Name: Type the file name you want to assign to the files when sending to the

FTP server. You can use up to 10 alphanumeric characters, - (hyphen) and _ (underline) for naming.

 Suffix: Select a suffix to add to the file name

 Date & time: The date & time suffix is added to the Image file name. The date/time

suffix consists of lower two-digits of year (2 digits), month (2 digits), date (2 digits), hour (2 digits), minute (2 digits), second (2 digits), and consecutive number (2 digits), thus 14-digit number is added to the file name.

Setting-Advanced FTP Client

Page 64

F7110 / F7115 User Manual

 Sequence number: A consecutive number of 10 digits between 0000000001 and

4294967295 and two fixed digits 00 is added to the Image file name.

 Sequence number clear: Click Clear and the suffix of the sequence number returns

to 1.