ZAVIO 5115F User Manual

Download

Page 1

F5100 / F5105 / F5110 / F5115 User Manual

Page 2

F5100 / F5105 / F5110 / F5115 User Manual

Contents

CHAPTER 1. SAFETY INSTRUCTION ....................................................................................................................... 1

CHAPTER 2. MINIMUM SYSTEM REQUIREMENT & PRODUCT FEATURE .................................................. 3

2.1 S

YSTEM REQUIREMENT ..........................................................................................................................................3

2.2 PRODUCT FEATURES ...............................................................................................................................................4

CHAPTER 3. USING IP CAMERA VIA WEB BROWSER ........................................................................................5

3.1 W

INDOWS WEB BROWSER......................................................................................................................................5

3.2 MAC WEB BROWSER...............................................................................................................................................6

CHAPTER 4. SETTING UP WIRELESS CONFIGURATION (ONLY FOR F5105 / F5115 ).................................. 8

CHAPTER 5. OPERATING IP CAMERA VIA MOBILE PHONE......................................................................... 10

5.1 M

OBILE PHONE VIEWING ..................................................................................................................................... 10

5.2 USING IP CAMERA VIA IPHONE............................................................................................................................. 11

CHAPTER 6. MSN MESSENGER...............................................................................................................................12

CHAPTER 7. CONFIGURATION OF MAIN MENU................................................................................................ 15

7.1 L

IVE VIEW ............................................................................................................................................................. 16

7.2 SETTING................................................................................................................................................................. 18

7.3 CLIENT SETTING ................................................................................................................................................... 19

7.4 I

MAGE SETUP......................................................................................................................................................... 20

CHAPTER 8. SETTING-BASIC................................................................................................................................... 21

8.1 S

YSTEM .................................................................................................................................................................. 21

8.1.1 Information....................................................................................................................................................21

8.1.2 Date / Time..................................................................................................................................................... 21

8.1.3 Initialize ......................................................................................................................................................... 23

8.1.4 Language....................................................................................................................................................... 24

8.2 C

AMERA................................................................................................................................................................. 25

8.2.1 General .......................................................................................................................................................... 25

8.2.2 H.264..............................................................................................................................................................27

8.2.3 MPEG-4......................................................................................................................................................... 28

8.2.4 MJPEG .......................................................................................................................................................... 30

8.2.5 3GPP.............................................................................................................................................................. 31

8.2.6 Advanced........................................................................................................................................................ 32

8.2.7 Playback.........................................................................................................................................................34

8.3 N

ETWORK .............................................................................................................................................................. 35

8.3.1 Information....................................................................................................................................................35

8.3.2 PPPoE............................................................................................................................................................ 36

8.3.3 DDNS (Dynamic DNS) .................................................................................................................................38

8.3.4 UPnP (Universal Plug and Play) .................................................................................................................. 42

8.3.5 Bonjour.......................................................................................................................................................... 43

8.3.6 IP Notification ............................................................................................................................................... 44

8.3.7 Wireless (Only for F5105 / F5115)................................................................................................................ 45

8.3.8 Messenger...................................................................................................................................................... 47

8.4 S

ECURITY............................................................................................................................................................... 49

8.4.1 Account.......................................................................................................................................................... 49

8.4.2 HTTPS........................................................................................................................................................... 50

8.4.3 IP Filter .........................................................................................................................................................51

CHAPTER 9. SETTING-ADVANCED ........................................................................................................................52

9.1 FTPC

LIENT........................................................................................................................................................... 52

9.1.1 General .......................................................................................................................................................... 52

Page 3

F5100 / F5105 / F5110 / F5115 User Manual

9.1.2 Alarm Sending...............................................................................................................................................

9.1.3 Periodical Sending ........................................................................................................................................ 55

9.2 SMTP ....................................................................................................................................................................56

9.2.1 General .......................................................................................................................................................... 56

9.2.2 Alarm Sending............................................................................................................................................... 58

9.2.3 Periodical Sending ........................................................................................................................................ 59

9.3 N

ETWORK STORAGE .............................................................................................................................................61

9.3.1 General .......................................................................................................................................................... 61

9.3.2 Alarm sending................................................................................................................................................ 62

9.3.3 Periodical recording...................................................................................................................................... 63

9.4 HTTPE

VENT......................................................................................................................................................... 65

9.4.1 General .......................................................................................................................................................... 65

9.4.2 Alarm Sending............................................................................................................................................... 66

9.5 A

LARM OUTPUT ....................................................................................................................................................69

9.6 SCHEDULE..............................................................................................................................................................71

9.7 ALARM INPUT ........................................................................................................................................................72

9.8 A

LARM BUFFER .....................................................................................................................................................73

9.9 MOTION DETECTION.............................................................................................................................................74

9.10 AUDIO DETECTION .............................................................................................................................................. 75

9.11 S

YSTEM LOG........................................................................................................................................................76

CHAPTER 10. APPENDIX ........................................................................................................................................... 77

A. F

RAME-RATE AND BITRATE TABLE ........................................................................................................................ 77

A.1 Mega Mode .......................................................................................................................................................80

A.2 VGA Mode.........................................................................................................................................................83

TORAGE REQUIREMENT TABLE............................................................................................................................83

B. S

B.1 Mega Mode ......................................................................................................................................................83

B.2 VGA Mode........................................................................................................................................................ 85

C. S

YSTEM REQUIREMENT ......................................................................................................................................... 87

C.1. 16 Channel IPCamera with CIF Performance.............................................................................................. 87

C.2. 16 Channel IPCamera with D1 Performance................................................................................................ 87

EUROPE – EU DECLARATION OF CONFORMITY .............................................................................................. 88

FEDERAL COMMUNICATION COMMISSION INTERFERENCE STATEMENT ............................................90

Page 4

F5100 / F5105 / F5110 / F5115 User Manual

User Manual

Chapter 1. Safety Instruction

¾ Before you use this product

This product has been designed with safety in mind. However, the electrical products can cause fires which may lead to serious body injury if not used properly. To avoid such accidents, be sure to heed the following.

¾ Legal Caution

Video and audio surveillance can be forbidden by laws that vary from country to country. Check the laws in your local region before using this product for surveillance purposes.

¾ Don't open the housing of the product

Don't try to open the housing or remove the covers which may expose yourself to dangerous voltage or other hazards.

¾ Don't use the accessories not recommend by the manufacturer

¾ Heed the safety precautions

Be sure to follow the general safety precautions and the “Operation Notice.”

¾ Operation Notice - Operating or storage location

Avoid operating or storing the camera in the following locations:

x Extremely hot or cold places

(Operating temperature: 0 °C to + 50 °C [32 °F to 122°F] )

x Exposed to direct sunlight for a long time, or close to heating equipment (e.g., near heaters) x Close to water (e.g.,near a bathtub, kitchen sink, laundry tub) x Close to sources of strong magnetism x Close to sources of powerful electromagnetic radiation, such as radios or TV transmitters x Locations subject to strong vibration or shock

¾ In case of a breakdown

In case of system breakdown, discontinue use and contact your authorized dealer.

Safety Instruction

Page 5

F5100 / F5105 / F5110 / F5115 User Manual

¾ In case of abnormal operation

x If the unit emits smoke or an unusual smell, x If water or other foreign objects enter the cabinet, or x If you drop the unit or damage the cabinet:1 Disconnect the cable and the connecting cables. 2

Contact your authorized dealer or the store where you purchased the product.

¾ Transportation

When transporting the camera, repack it as originally packed at the factory or in materials of equal quality.

¾ Ventilation

To prevent heat buildup, do not block air circulation around the device.

¾ Cleaning

x Use a soft, dry cloth to clean the external surfaces of the device. Stubborn stains can be

removed using a soft cloth dampened with a small quantity of detergent solution, then wipe dry.

x Do not use volatile solvents such as alcohol, benzene or thinners as they may damage the

surface.

Safety Instruction

Page 6

F5100 / F5105 / F5110 / F5115 User Manual

Chapter 2. Minimum System Requirement &

Product Feature

2.1 System Requirement

For normal operation and viewing of the network camera, it’s recommended that your system meet these minimum requirements for proper operation:

Item Requirements

CPU Pentium 4, 2.8GHz (or equivalent AMD)

Graphic Card 258 MB RAM graphic cards(or equivalent on-board graphic cards)

RAM 1G

Operating System

Web Browser Internet Explore 6 or later

Note: Please keep updating the latest Windows software and service package. (Ex: Net

Framework, Windows Media Player, Enhance ActiveX Security)

Windows 2000, Windows 2003, Windows XP, Windows Vista, Windows 7, and Mac OS X Leopard

Minimum System Requirement & Product Feature

Page 7

F5100 / F5105 / F5110 / F5115 User Manual

˛˔˥˗˪˔˥˘ʳ

2.2 Product Features

These easy-to-follow instructions make setup and operation quick and simple, so you’ll also soon be enjoying the benefits of these product features:

SYSTEM

H.264 / MPEG-4 / Motion JPEG:

Resolutions

Screen Resolution Compressing Format

Frame Rate

Image Settings

Image Snapshot Video Recording Full Screen Viewing Digital Zoom

Audio

Instant Messenger Mobile Phone Live View Alarm Sending Security

Alarm Buffer

Supported Protocols

Simultaneous Connection Operating Conditions

Lens

IR LEDs IR Working Distance I / O Audio Output Alarm Input Power

Ethernet Wireless

4 resolutions from 1280x1024 to 320x240 via API and configuration web page

Higher than 1024 * 720 pixels

H.264 / MPEG-4 / Motion JPEG Up to 15 fps at 1280x1024 Up to 30 fps at 640x480 Rotation: Mirror, Flip, Mirror Flip Brightness / Contrast / Saturation / Sharpness Overlay capabilities: time, date, text and privacy image Yes Yes Yes 10x digital Two-way (full / half duplex) with built-in microphone Audio compression: G.711 ȝ law, a law, and AMR Support MSN Live View

Through 2.5 WAP,

3G Streaming, and 3G Browser FTP Client / SMTP / Network Storage / HTTP Event Passward Protecton / HTTPS encryption / IP Filter Recording image and audio file pre-and-post disconnection up to 5 sec. Bonjour, TCP/IP, DHCP, PPPoE, ARP, ICMP, FTP, SMTP, DNS, NTP, UPnP, RTSP, RTP, HTTP, TCP, UDP, 3GPP/ISMA RTSP Up to 10 users 0 ~ 50 к (32 ~ 122 л)

F1.8, 4.2mm Megapixel board lens (for F5110 / F5115) F1.2~Ќ 4.0mm Megapixel CS-mount lens (for F5100 / F5105) 5 ĳ IR LEDs x 12 (for F5110 / F5115) 10M 1 in / 1 out 1 1 12V DC, 1A, Max 5W

NETWORK

10 / 100 Base T (for F5100 / F5110) IEEE 802.11b/g (for F5105 / F5115)

Minimum System Requirement & Product Feature

Page 8

F5100 / F5105 / F5110 / F5115 User Manual

Chapter 3. Using IP Camera via Web Browser

3.1 Windows Web Browser

1. Open your web browser, and enter the IP address or host name of the IP camera in the Location / Address field of your browser.

Note : If you only want to view the video without accessing Stting screen, enter

“http://<IP>/index2.htm” as your web URL.

2. Use the default account “admin” and default password “admin”.

Note : The default user name “admin” and the password are set at the factory for the

administrator. You can change them in the Account Menu. (Please check “Setting ĺ

Basic ĺ Security ĺ Account”)

3. The monitor image will be displayed in your browser. In the far left side of main configuration are Setting, Client Setting, and Image Setup. For more details, you can check Chapter 7.2ΕChapter 7.3ΕChapter 7.4 and Chapter 7.5.

Using IP Camera via Web Browser

Page 9

F5100 / F5105 / F5110 / F5115 User Manual

3.2 Mac Web Browser

1. Click the Safari icon, and enter the IP address of the IP camera in the Location / Address field of your browser.

Note : If you only want to view the video without Setting screen

“http://<IP>/index2.htm” as your web URL.

2. Enter the default account “admin” and default password “admin”.

Note : The default user name “admin” and the password are set at the factory for the

administrator. You can change them in the Account Menu (Please check “Setting ĺ

Basic ĺ Security ĺ Account”)

Using IP Camera via Web Browser

Page 10

F5100 / F5105 / F5110 / F5115 User Manual

Using IP Camera via Web Browser

Page 11

F5100 / F5105 / F5110 / F5115 User Manual

Chapter 4. Setting up Wireless Configuration (Only for F5105 / F5115 )

The wireless network has to be set up by using cable network connection. After setting the

camera correctly, the wireless function can work without cable network connection. Please

follow the setting process below step by step:

1. Connect IP Camera with Ethernet connection.

2.Go to “Setting Ш Basic Ш Network Ш Wireless,” choose option “On”. You will see

the wireless Setting screen.

3. Then click “Refresh”. All access points (AP) around you will show up.

4. Select the AP you wish to connect.

5. Enter password at active transmit key if you need. If you don't know the setting of the

wireless AP, please ask your network administrator.

Setting up Wireless Configuration

Page 12

F5100 / F5105 / F5110 / F5115 User Manual

6. Choose the option of Obtain an IP address automatically (DHCP) and Obtain DNS server address automatically.

7. Otherwise, Choose Use the following IP address and Use the following DNS sever address.

¾ Use the following IP address: Select this when the fixed IP address is set.

zIP address: Enter the IP address of the device. zSubnet mask: Enter the subnet mask. zDefault gateway: Enter the default gateway.

¾ Use the following DNS server address: Select this when you set the fixed address as the

IP address of DNS server.

zPrimary DNS server: Enter the IP address of the primary DNS server. zSecondary DNS server: Enter the IP address of the secondary DNS server, if

necessary.

Setting up Wireless Configuration

Page 13

F5100 / F5105 / F5110 / F5115 User Manual

Chapter 5. Operating IP Camera via Mobile Phone

5.1 Mobile Phone Viewing

5.1.1 3G Mobile Phone Streaming Viewing

For 3G mobile phone viewing, type “ rtsp://<IP>:<PORT>/video.3gp ” into your 3G

Streaming Link. <IP> is the Public IP address of your IP camera; <PORT> is the RTSP port

of your IP camera (Default value is 554.) Example: rtsp://100.10.10.1:554/video.3gp

Note: You can also use RTSP clients (RealPlayer, VLC, QuickTime Player…etc.) to

view RTSP streaming, just type in “rtsp://<IP>:<PORT>/video.3gp” as the Player URL

5.1.2 2.5G Mobile Phone WAP Viewing

For 2.5G mobile phone viewing, type “http://<IP>/mobile.wml ” into your 2.5G WAP

Browser. <IP> is the Public IP address of your IP camera.

5.1.3 2.5G Mobile Phone Browser Viewing

For 2.5G mobile phone viewing, type “http://<IP>/mobile.wml ” into your 2.5G Web

Browser. <IP> is the Public IP address of your IP camera.

Using IP Camera via Mobile Phone

Page 14

F5100 / F5105 / F5110 / F5115 User Manual

5.2 Using IP Camera via iPhone

You can use ZAVIO Web User Interface via iPhone. Please follow the setting process below.

Then you can use ZAVIO Web UI via iPhone.

1. Select Safari function

3. Type name and password. Default value is admin / admin. Then click Login In

2. Type IP address in your web link.

4. The ZAVIO User Interface and live image will show up in the middle of screen.

Using IP Camera via Mobile Phone

Note: The image is continuous snapshots, not video. Thus, live image can’t be recorded here.

Page 15

F5100 / F5105 / F5110 / F5115 User Manual

Chapter 6. MSN Messenger

Please follow the following steps to set up the Messenger function.

1. Download free MSN software and create a new MSN account (Camera at home) for Microsoft Live Messenger.

2.Go to “SettingШBasicШNetworkШMessenger,” set the Messenger to “ON” . Then, login in new

account and password (Camera at home).

3. If your router has firewall function, you have to set the Port Range on this setting page in accordance with the one of firewall.

4. Choose the Video Mode, decide the live view image of messenger received from Computer View (MPEG-4) or Mobile View (3GPP).

5. Choose “On” at the option of IP Notification. If this feature switches On, camera will send IP notification to the users who are allowed.

6. Choose “On” at the option of Privacy. If you can choose “On” at the privacy option, you can set an allow list.

7. Use your account to login in the Messenger software. Then, add the new MSN account (Camera at home )

8. The Camera at home will show up with its Public IP and Private IP if the option of IP Notification is “On”. ( You can enter “Ping” to show up with Public IP and Private IP. )

9. Click on the small camera icon . Then, choose “View a new contact's webcam”.

MSN Messenger

Page 16

F5100 / F5105 / F5110 / F5115 User Manual

10. The IP Camera will accept your invitation; the live video will show up in the right screen after few seconds.

11. Click Action button and choose Start Control Panel to use control panel.

12. The dialog box will show up with “This

application is not part if Window Live Message…….” Tick the box of “Don’t show me this again” and click OK.

13. The IP Camera will accept your invitation to start Control Panel.

MSN Messenger

Page 17

F5100 / F5105 / F5110 / F5115 User Manual

14. You can click Camera icon to snapshot then the picture will send to you

immediatel

15. You can click paint palette icon showing up with tool bar to set up image. Then, you can use the tool bar to optimize

video Brightness , Contrast , Saturation and Sharpness . After

the adjustment of all setting, you can still

click to make the setting back to the original setting.

MSN Messenger

Page 18

F5100 / F5105 / F5110 / F5115 User Manual

Chapter 7. Configuration of Main Menu

In the left side of main configuration are Setting, Client Setting, Image Setting. For more details, please check Chapter 7.2ΕChapter 7.3ΕChapter 7.4.ΕChapter 7.5.

In the right side, you can control Live View in your main Browser. The function includes Snapshot, Open Digital Zoom, Audio, and Video Play.

Full screen

Snapshot

Video play

Open digital zoom

Configuration of Main Menu

Page 19

F5100 / F5105 / F5110 / F5115 User Manual

7.1 Live View

7.1.1 Snapshot

You can capture a still image shot by clicking the camera icon and save it in the operating computer.

Symbols Meaning

a snapshot window appears after clicking the icon

co er cmput omputer.

Save save the picture captured by snapshot into your computer

Close Return to the view screen

full screen

7.1.2 Digital zoom in / out the image via the monitor window

z Click to display the digital zoom in window.

z Pull the to adjust the digital zoom range, and it will be

showed on the above window.

z Use the left click of your mouse to move to anywhere in the window area.

Configuration of

Main Menu

Page 20

F5100 / F5105 / F5110 / F5115 User Manual

7.1.3 Video play buttons

Symbols Meaning

Pause the current video

Play the video

Stop the current video

Record the current video

Note: Concerning the recording storage requirement of your hard disk, please refer to

the CHAPTER 10. APPENDIX / B. Storage Requirement Table.

7.1.4 Audio buttons

Symbols Meaning Note

Speakers turned on

Speakers turned off

Mute off

Mute on

Volume control bar

mean the speakers of your computer are turned on to transmit the sounds from the connected IP camera(s)

mean the speakers of your computer are turned off to transmit the sounds from the connected IP camera(s)

mean you can broadcast to the connected IP camera(s) via the Ethernet using your microphone

mean you can’t broadcast to the connected IP camera(s) via the Ethernet using your microphone

mean you can adjust the sound volume by the control bar

Configuration of

Main M

enu

Page 21

F5100 / F5105 / F5110 / F5115 User Manual

7.2 Setting

This function is only for the Administrator. Click “Setting” on the home page of web user interface to get into the Basic and Advanced Settings menu.

Click Basic folder, there are sub-folders including System, Camera, Network, and Security. Fore more information, you can see Chapter 8.1ΕChapter 8.2ΕChapter 8.3 and Chapter 8.4.

Click Advanced folder, there are sub-folders including FTP Client, SMTP, Network Storage, HTTP Event, Alarm Output, Schedule, Alarm Input, Alarm Buffer, Motion Detection, Audio Detection, and System Log. Fore more information, please see Chapter 9.

Configuration of

Main M

enu

Page 22

F5100 / F5105 / F5110 / F5115 User Manual

7.3 Client Setting

This function is only for the client. Click this button to control Mode, View Size, Protocol, and Video Buffer.

7.3.1 Mode

Click the pull-down box to choose video compression mode of LIVE VIEW among H.264, MPEG-4, and MJPEG.

Note: As long as the operating system not able to afford loading under H.264 mode, please

downgrade the mode to MPEG-4 or MJPEG.

7.3.2 View Size

Select the desired view size of image resolution among 1/4X, 1/2X, and 1X.

7.3.3 Protocol

Select the transferring protocol among TCP, UDP, and HTTP.

7.3.4 Video Buffer

Turn the Video Buffer function On / Off. The Video Buffer function makes the streaming more smoothly in unsteady network environment, but might cause a little delay in live viewing.

Configuration of Main Menu

Page 23

F5100 / F5105 / F5110 / F5115 User Manual

7.4 Image Setup

The tool bar can be adjusted to optimize video Brightness, Contrast, Saturation and

Sharpness.

7.4.1 Brightness

The value range is 0~99. The higher value the brightness is, the brighter the image is.

7.4.2 Contrast

The value range is 0~99. The contrast is a measure of a display system, defined as the ratio of white to black that the system is capable of producing. The higher value the contrast is, the more delicate of color you can have.

7.4.3 Saturation

The value range is 0~99. The saturation of a color is determined by a combination of light intensity and how much it is distributed across the spectrum of different wavelengths. The higher value the saturation is, the more colorful the image will be.

7.4.4 Sharpness

The value range is 0~99. It applies image processing techniques to adjust the sharpness of live view. However, higher the value is, more the noise is.

7.4.5 Default

After the adjustment of all setting, you can still click Default to make the setting back to the original setting.

Configuration of Main Menu

Page 24

F5100 / F5105 / F5110 / F5115 User Manual

Chapter 8. Setting-Basic

Click the Basic folder to display the sub folders including System, Camera, Network, and

Security.

8.1 System

Click the folder of System to display the sub-folders including Information, Date / Time,

Initialize, and Language.

8.1.1 Information

The Information screen provides the product factory information which includes Product

Name, Firmware Version.

8.1.2 Date /

The Date/ Time screen displays all options of time setting.

Setting-Basic Information

Time

Page 25

F5100 / F5105 / F5110 / F5115 User Manual

¾ Current Date / Time: This displays the current date and time of this IP Camera.

¾ PC Clock: This displays the date and time of the monitoring PC clock. ¾ Date / Time Format: You can click the pull down box to select different time display

formats.

Note: If you would like the Date / Time information shows on the Live View screen,

please check “Setting ĺ Basic ĺ Camera ĺ General ĺ Date / Time ” to execute the

setting.

¾ Adjust: You can select one of those four adjusting modes for your IP Camera.

zKeep current setting: Select this mode to keep the current date and time of this IP

Camera.

zSynchronize: Select this mode to keep the date and time of this IP Camera is the same

as the monitoring PC.

zManual setting: Select this mode to adjust manually the date and time of this IP

Camera.

zSynchronize with NTP: Specify the NTP server name and the Refresh Interval to

synchronize the date and time of this IP Camera with those of the time server, known as the NTP server.

Setting-Basic Date/Time

Page 26

F5100 / F5105 / F5110 / F5115 User Manual

¾ Time Zone: Select the Time Zone format of Greenwich Mean Time among different

cities. The time display will be the same as the current date / time option.

¾ Daylight Saving Time: There are two modes to choose for setting up daylight saving

time.

zBy Date: Set the start and end time by select month, day, hour, and minute. zBy Week Number: Set the start and end time by select month, week, hour, and

minute.

Note: The NTP server (Network Time Protocol) is the time server which is an Internet

standard protocol built on the top of TCP / IP. This assures accurate synchronization to

the millisecond of computer clock times in a network of computers.

8.1.3 Initialize

¾ Reboot: Click this button to reboot this IP Camera. A confirmation dialogue will appear and then click “OK” to execute. It takes one minute to complete the reboot process.

¾ Factory Default: Click this bottom to recover this IP Camera to the factory default setting. A confirmation dialogue will appear and then click “OK” to execute. The network indicator on this IP Camera will start to blink. This IP Camera will reboot automatically after completing adjustments to the default setting. Don't turn off this IP Camera until the device reboots.

¾ Backup Setting: You can save the setting data of this IP Camera into a file. Click “Save”

Setting-Basic

Initialize

Page 27

F5100 / F5105 / F5110 / F5115 User Manual

and follow the instructions on the browser to save the setting data file to the location you specified.

¾ Restore Setting: Download the saved setting data of this IP Camera. Click “Browse” and select saved file. Click “OK” and this IP Camera is adjusted according to the loaded data and then restarted.

¾ Firmware Update: Update the device software. Click “Browse” and select the file for updating. A confirmation dialogue will appear. Click “OK” to start. This IP Camera will reboot upon completion.

Note: When updating the firmware version, please use the file specific for the model.

Otherwise, some problems may occur. Unless the updating completed, please don’t

turn off the power or disconnect the network.

8.1.4 Language

¾ Upload Language Pack: Clicking “Browse” and selecting the file for updating, the present language display of WEB User Interface could be changed. A confirmation dialogue will appear. Click “OK”, then the update will be applied immediately. The default language is “English.”

Setting-Basic Language

Page 28

F5100 / F5105 / F5110 / F5115 User Manual

8.2 Camera

Click the folder of Camera to display the sub folders including General, H.264, MPEG-4,

MJPEG, 3GPP, Advanced, and Playback.

8.2.1 General

¾ RTSP: The default value is 554. If the IP Cameras connected with router and installed

outside are over 2 sets and all of them need support RTSP, please fill some value in the blank space in the range from 1024 to 65535.

¾ RTP Unicast Streaming: The default value of port range is 5000 ~ 7999 and can be

changed from 1024 to 65535.

Note: Under Unicast streaming mode, streaming video is delivered from the camera to

a single client device.

¾ Image Rotated: Select the screen display “flip”, “mirror”, or “flip + mirror.”

¾ Audio Codec: Select one audio codec among G.711 U-law / G.711 A-law / AMR Audio /

Off.

zG.711 u-law : one codec for “Computer Audio”, used in North America & Japan areas. zG.711 a-law : another codec for “Computer Audio”, used in Europe and the rest of the

world.

zAMR audio: an audio codec of the third generation communication for MOBIL

PHONE. While the option selected, your mobile phone will receive the audio file

Setting-Basic Camera

Page 29

F5100 / F5105 / F5110 / F5115 User Manual

from IP Camera. And you can choose the bit rate from 4.75k to 12.2k. However, the usage of this codec will cause frame-rate decreasing.

zOff: Select Off, audio file won’t be transmitted by IP Camera.

¾ Audio Mode: You can select Full duplex or Half duplex.

zFull duplex: Select it for simultaneous communication in both direction between the

connected administrator and IP CAM. It means both parties can speak and be heard at the same time.

zHalf duplex: Select it for communication in both directions, but only one direction at

a time (not simultaneously). It means one party begins receiving a signal, it must wait for the transmitter to stop transmitting, before replying. Therefore, once one party speak, he can’t hear any voice from the other party, just like the communication by radio set.

¾ Video Clip Format: Select RECORDING compression format H.264 or MPEG-4.

zMPEG-4: MPEG-4 has the advantage of sending a lower volume of date per time

unit across the network (bit-rate) compared to Motion JPEG and therefore provides a relatively high image quality at a lower bit-rate (bandwidth usage).

zH.264: H.264 provides higher compression rate than MPEG-4. Thus, H.264 can

decrease the bandwidth usage and further apply on 3G. However, H.264 will occupy more system resources than MPEG-4. As long as the operating system appears operating difficulties under H.264 format, please change to select MPEG-4.

¾ IR Threshold (only for F5110/F5115): Select LED light On, Off, or Auto.

zOn: Select On will led always work. zOff: Select off will disable led. zAuto: Select Auto will appear two thresholds, Bright and Dark. You can adjust them

for IR Auto-On and Auto-Off respectively. Bright value higher, IR auto-off more easily in the bright environment will be. Dark value higher, led auto-on more easily in the dark environment will be. Bright Value is ranges from 0 to 70, and Dark Value is from 30 to 100. The interval value between both is at least 30. The default value for F5110/F5115 is 50 and 85.

¾ Overlay:

zText Overlay: Some information can be showed on the display screen, such as Date /

Time and user-defined text. And the background color can be chosen.

zPrivacy Mask: A specific area of the video image can be covered.

Setting-Basic Camera

Page 30

F5100 / F5105 / F5110 / F5115 User Manual

8.2.2 H.264

¾ Viewer Authentication:

zOn: If the viewer authentication is On, the users will be requested to key-in username

and password when using QuickTime Player. to have live viewing.

zOff: If the viewer authentication is Off, you can have live viewing on computer by

QuickTime Player after entering “rtsp://ip:port/video.h264” on the URL column directly.

¾ Multicasting Streaming (if it’s on):

zMulticast Address: The multicast server address will appear automatically. zVideo / Audio Port: Specify the transmission port number of the video data, from

1024 to 65534.

zTime to Live: Set the maximum TTL that multicast can pass through.

Note: Time To Live option determines the maximum length of time (measure as the

number of network routers that can be passed before data arrives at its destination or

is dropped) within which a multicast packet must reach its destination.

¾ Image Size: Specify the image size when the network camera transmits. Choose one among 1280 x 1024, 1280 x 720, 640 x 480, and 320 x 240.

¾ Frame Rate: Set the frame rate of H.264 image. Choose one value among 2, 3, 4, 5, 7, 10, 15, 20, 25, and 30 fps. The unit “fps” stands for “frames per second”.

Note: The frame rate is up to 15 fps at 1280x1024, and up to 30 fps at 640x480.

However, if you would like choose frame rate over 15 fps, the IMAGE SIZE of

H.264/MPEG-4/MJPEG setting page has to been selected 320x240 or 640x480 at the

same time.

Setting-Basic

Camera

Page 31

F5100 / F5105 / F5110 / F5115 User Manual

¾ Quality:

zAuto: The quality and bitrate will be adjusted automatically according to the frame

rate.

zFixed Quality: Select the value of quality among Medium, Good, Delicate and

Excellent.

zFixed Bitrate: Set the bitrate of H.264 image transmission for a line. Select one among

64Kbps, 128Kbps, 256Kbps, 384Kbps, 512Kbps, 768Kbps, 1Mbps, 1.5 Mbps, 2 Mbps, 3 Mbps, 4 Mbps, 5 Mbps, and 6 Mbps.

Note: Concerning how to select the suitable image quality for Fixed Quality or Fixed

Bitrate, please refer to the CHAPTER 10. APPENDIX / A. Frame-rate & Bitrate Table.

¾ IP interval: It’s the ratio of i-frame & p-frame. Select one among 1, 5, 10, 15, 30, 60, and

120. The ratio smaller, the streaming smoother.

Note: The IP interval value means a ratio of “ P-frame / I-frame “ in a certain section of

frame sequences. The ratio lower, the live view clear. However, live view will lag if the

bandwidth isn’t big enough. In this situation, you have to choose another bigger IP interval

value to solve the problem.

Note: If Video Clip Format of General Menu (go “Setting ĺ Basic ĺ Camera ĺ

General” ), which is for recording compression, is chosen H.264, the IP interval option will

appear “Auto” automatically and can’t select. The limit is for avoiding damaging the

recording quality of 5 seconds temporary-saved video recorded on FTP server.

8.2.3 MPEG-4

Setting-Basic Camera

Page 32

F5100 / F5105 / F5110 / F5115 User Manual

¾ Viewer Authentication:

zOn: If the viewer authentication is On, the users will be requested to key-in username

and password when using QuickTime Player. to have live viewing.

zOff: If the viewer authentication is Off, you can have live viewing on computer by

QuickTime Player after entering “rtsp://ip:port/video.mp4” on the URL column directly.

¾ MulticaSting Streaming (if it’s on):

zMulticast Address: Specify the multicast server address. zVideo / Audio Port: Specify the transmission port number of the video data, from

1024 to 65534.

zTime to Live: Set the maximum TTL that multicast can pass through.

Note: Time To Live option determines the maximum length of time (measure as the

number of network routers that can be passed before data arrives at its destination or

is dropped) within which a multicast packet must reach its destination.

¾ Image Size: Specify the image size when the network camera transmits. Choose one among 1280 x 1024, 1280 x 720, 640 x 480, and 320 x 240.

¾ Frame Rate: Set the frame rate of the MPEG-4 image. Choose one from 1, 2, 3, 4, 5, 7, 10, 15, 20, 25, and 30 fps. The unit “fps” stands for “frames per second.”

Note: The frame rate is up to 15 fps at 1280x1024, and up to 30 fps at 640x480.

However, if you would like choose frame rate over 15 fps, the IMAGE SIZE of

H.264/MPEG-4/MJPEG setting page has to been selected 320x240 or 640x480 at the

same time.

¾ Quality:

zAuto: The quality and bitrate will be adjusted automatically according to the frame

rate.

zFixed quality: Select the value of quality among Medium, Good, Delicate and

Excellent.

zFixed bitrate: Set the bitrate of MPEG-4 image transmission for a line. You can select

one value among 64Kbps, 128Kbps, 256Kbps, 384Kbps, 512Kbps, 768Kbps, 1Mbps,

1.5 Mbps, 2 Mbps, 3 Mbps, 4 Mbps, 5 Mbps, and 6 Mbps.

Note: Concerning how to select the suitable image quality for Fixed Quality or Fixed

Bitrate, please refer to the CHAPTER 10. APPENDIX / A. Frame-rate & Bitrate Table.

¾ IP Interval: It’s the ratio of i-frame & p-frame. You can select one among 1, 5, 10, 15, 30, 60, and 120. The ratio smaller, the streaming smoother.

Note: The IP interval value means a ratio of “ P-frame / I-frame “ in a certain section of

frame sequences. The ratio lower, the live view clear. However, live view will lag if the

bandwidth isn’t big enough. In this situation, you have to choose another bigger IP interval

Setting-Basic

Camera

Page 33

F5100 / F5105 / F5110 / F5115 User Manual

value to solve the problem.

Note: If Video clip format of General Menu, which is for recording compression, is chosen

MPEG-4, the IP interval option will appear “Auto” automatically and can’t select. The limit

is for avoiding damaging the recording quality of 5 seconds temporary-saved video

recorded on FTP server.

8.2.4 MJPEG

¾ Viewer Authentication:

zOn: If the viewer authentication is On, the users will be requested to key-in username

and password when using QuickTime Player to have live viewing.

zOff: If the viewer authentication is Off, you can have live viewing on computer by

QuickTime Player after entering “rtsp://ip:port/video.mjpg” on the URL column directly.

¾ Multicast Sting Streaming (if it’s on):

zMulticast Address : Specify the multicast server address. zVideo / Audio Port: Specify the transmission port number of the video data, from

1024 to 65534.

zTime to Live: Set the maximum TTL that multicast can pass through.

Note: Time To Live option determines the maximum length of time (measure as the

number of network routers that can be passed before data arrives at its destination or

is dropped) within which a multicast packet must reach its destination.

¾ Image Size: Specify the image size when the network camera transmits. Choose among 1280 x 1024, 1280 x 720, 640 x 480, and 320 x 240.

¾ Frame Rate: Set the frame rate of the MJPEG image. Choose one among 1, 2, 3, 4, 5, 7,

Setting-Basic

Camera

Page 34

F5100 / F5105 / F5110 / F5115 User Manual

10, 15, 20, 25, and 30 fps. The unit “fps” stands for “frames per second”.

Note: The frame rate is up to 15 fps at 1280x1024, and up to 30 fps at 640x480.

However, if you would like choose frame rate over 15 fps, the IMAGE SIZE of

H.264/MPEG-4/MJPEG setting page has to been selected 320x240 or 640x480 at the

same time.

¾ Quality:

zAuto: The quality and bit rate will be adjusted automatically according to the frame

rate.

zFixed Quality: Select the value of quality among Medium, Good, Delicate and

Excellent.

zFixed Bitrate: Set the bitrate of MJPEG image transmission for a line. You can select

one among 64Kbps, 128Kbps, 256Kbps, 384Kbps, 512Kbps, 768Kbps, 1Mbps, 1.5 Mbps, 2 Mbps, 3 Mbps, 4 Mbps, 5 Mbps, and 6 Mbps.

Note: Concerning how to select the suitable image quality for Fixed Quality or Fixed

Bitrate, please refer to the CHAPTER 10. APPENDIX / A. Frame-rate & Bitrate Table.

8.2.5 3GPP

¾ Viewer Authentication:

zOn: If the viewer authentication is On, the users will be requested to key-in username

and password when using QuickTime Player to have live viewing.

zOff: If the viewer authentication is Off, you can have live viewing on computer by

QuickTime Player after entering “rtsp://ip:port/video.3gp” on the URL column directly.

¾ Image Size: Image size for 3GPP is 160 x 120.

¾ Frame Rate: Set the frame rate of the 3GPP image. Choose one between 5 or 10 fps.

¾ Quality:

zAuto: The quality and bit rate will be adjusted automatically according to the frame

Setting-Basic

Camera

Page 35

F5100 / F5105 / F5110 / F5115 User Manual

rate.

zFixed quality: This item here can’t be selected. zFixed bitrate: Set the bitrate of 3GPP image transmission for a line. You can select one

among 64Kbps, 48Kbps, 32Kbps, 16Kbps.

Note: Concerning how to select the suitable image quality for Fixed Quality or Fixed Bitrate,

please refer to the CHAPTER 10. APPENDIX / A. Frame-rate & Bitrate Table.

¾ IP interval: It’s the ratio of i-frame & p-frame. You can select one among 1, 5, 10, 15, 30, 60, and 120. The ratio smaller, the streaming smoother.

Note: The IP interval value means a RATIO of “ P-frame / I-frame “ in a certain section of

frame sequences. The ratio lower, the live view clear. However, live view will lag if the

bandwidth isn’t big enough. In this situation, you have to choose another bigger IP interval

value to solve the problem.

8.2.6 Advanced

¾ White Balance: Choose the white balance among Auto, Florescent, Incandescent and Black & White.

¾ Lighting: The default setting of lighting environment is Auto. However, you may also

choose 50 or 60 Hz upon the lighting environment of your country.

¾ Exposure Mode: Choose Auto or Manual upon the capture environment.

Setting-Basic

Camera

Page 36

F5100 / F5105 / F5110 / F5115 User Manual

zAuto: Choose Auto and you have 3 options to adjust the exposure condition.

9 Back light compensate: Click it on and it helps avoid problems in

situations where the main subject ends up being too dark, such as when shooting people or other subjects in front of a bright background.

9 Slow shutter: Click it on and the range of shutter speed will be from 1/5 to

1/120 sec. It will adjust the shutter speed automatically and helpful to capture the clear image when shooting in a dark place.

zHigh Speed Mode: Choose High Speed Mode and the shutter speed will be close

1/120 sec. as far as possible to help to capture the motion image of sports or high-speed phenomena.

zManual: Choose Manual and you can select options, including Shutter Speed and

Gain.

9 Shutter Speed: The default value is 1/30 sec. and you can select the value

among 1/4, 1/6, 1/12, 1/30, 1/60, and 1/120 sec.

9 Gain: The default value is 2 and the value is adjustable among 0~9. The

value of the gain will influence the brightness of the image. The more the value is , the brighter the image is. However, the higher gain value might cause more noise.

Setting-Basic

Camera

Page 37

F5100 / F5105 / F5110 / F5115 User Manual

8.2.7 Playback

Clicking the button of “Open files” and select the video file recorded previous, you can look for the desired image. Besides, you can still have the live view in the screen. The function of each button is as below illustration:

Snapshot

Mirror/ Flip

Full Screen

Setting-Basic Camera

Pause

Stop

Previous track

Volume

Mute on / Mute off

Open files

Open digital zoom

Next track

Page 38

F5100 / F5105 / F5110 / F5115 User Manual

8.3 Network

Click the folder of Network to display the sub folders including Information, PPPoE,

DDNS, UPnP, Bonjour, IP Notification, Wireless and Messenger.

8.3.1 Information

Display the MAC address of the device.

¾ Obtain an IP address automatically (DHCP): If a DHCP server is installed on the network, to select this while the IP address is assigned by the DHCP server.

¾ Obtain DNS server address automatically: Select this to obtain the address of DNS server automatically.

Setting-Basic Network

Page 39

F5100 / F5105 / F5110 / F5115 User Manual

Use the following IP address: Select this option when the fixed IP address is set.

zIP address: Enter the IP address of the device. zSubnet mask: Enter the subnet mask. zDefault gateway: Enter the default gateway.

¾ Use the following DNS server address: Select this when you set the fixed address as the

IP address of DNS server.

zPrimary DNS server: Enter the IP address of the primary DNS server. zSecondary DNS server: Enter the IP address of the secondary DNS server, if

necessary.

¾ HTTP Port Number: Select 80 in general situations. If you want to use a port number other than 80, select the text box and enter a port number between 1024 and 65535.

zWhen you have set the HTTP port number to a number other than 80 on the Network

Setting screen in the Setup Program, access the device by typing the IP address of the device on the web browser as follows: Example: when HTTP port number is set to 2000 http://192.168.1.100:2000/

Note: The IP Camera needs to be rebooted after it finishes changing the network setting

completely.

Note: If you connect the IP Camera with your computer directly, the default network domain

of camera is 192.168.1.xx

8.3.2 PPPoE

If your ISP provides Dynamic IP with authentication by username and password, type all PPPoE information in this part. When using the PPPoE function, you need to turn on the DDNS or IP Notification function at same time.

Setting-Basic Network

Page 40

F5100 / F5105 / F5110 / F5115 User Manual

¾ IP address: The IP address obtained at the PPPoE connecting with network.

¾ User ID: Enter the user ID for authentication necessary for PPPoE connections. Type it

up to 64 characters.

¾ Password: Enter the password for authentication necessary for PPPoE connections. Type it up to 32 characters.

¾ Re-type Password: Re-type the password to confirm.

¾ Obtain DNS server address automatically: Select this to obtain the address of DNS

server automatically.

¾ Use the following DNS server address: Select this when you set the fixed address as the IP address of DNS server.

zPrimary DNS server: Enter the IP address of the primary DNS server. zSecondary DNS server: Enter the IP address of the secondary DNS server.

Note : 1. PPPoE (Point-to-Point Protocol over Ethernet): PPPoE is a network protocol

for encapsulating Point-to-Point Protocol frames insider Ethernet frames. PPPoE

connection is used mainly with ADSL service where individual users connect to the

ADSL transceiver (modem) over Ethernet work. It also widely used in XDSL (digital

affiliate line such as ADSL, VDSL or SDSL)

2. The IP Camera needs to be rebooted after it finishes changing the network

completely.

3. The IP Camera with Intelligent IP Installer can’t be founded after turning on the

PPPoE and reboot.

Setting-Basic Network

Page 41

F5100 / F5105 / F5110 / F5115 User Manual

8.3.3 DDNS (Dynamic DNS)

DDNS is a system which allows the domain name data held in a name server to be updated in real time. The most common use for DDNS is allowing an internet domain name to be assigned to a computer with a varying / dynamic IP Address. This makes it possible for other sites on the internet to establish connection to the machine without needing to track the IP Address themselves.

¾ Server Name: Choose the DDNS Server from the list.

¾ User ID: Enter the user ID for authentication necessary for DDNS connections. Type it up

to 64 characters.

¾ Password: Enter the password for authentication necessary for DDNS connections. Type it up to 32 characters.

¾ Re-type Password: Re-type the password to confirm.

¾ Host Name: Enter the host name that is registered to the DDNS server.

Setting-Basic Network

Page 42

Note : How to apply DDNS username and Host name?? You can apply DDNS

username and Host name by the following steps:

1. Login http://www.dyndns.org, click the Creat Account

F5100 / F5105 / F5110 / F5115 User Manual

2. Input all information and follow step by step with DynDNS

Setting-Basic Network

Page 43

3. Login with new account and click Account ĺ My Hosts ĺ Add Host Services

F5100 / F5105 / F5110 / F5115 User Manual

4. Type domain in the Hostname field and select sub-domain

Setting-Basic Network

Page 44

5. After type information, check your DDNS service.

F5100 / F5105 / F5110 / F5115 User Manual

6. Type your DDNS User ID, Password and Host name in Setting ĺ Network ĺ DDNS. After completing setting, reboot IP Camera.

Setting-Basic Network

Page 45

F5100 / F5105 / F5110 / F5115 User Manual

8.3.4 UPnP (Universal Plug and Play)

If you have a Router to access to internet and the Router supports UPnP IGD function, you need to turn on the UPnP Port Forwarding function.

¾ HTTP Port: Enter the HTTP port number and default HTTP port is 80.

¾ SSL Port: Enter the SSL port number and default SSL port is 443.

¾ RTSP Port: Enter the RTSP port, default value is 554 for computer view.

Note : UPnP (Universal Plug and Play): UPnP is a set of computer network protocol. It

allows devices to connect seamlessly and simplify the implementation of networks in the

home and corporate environments.

Setting-Basic Network

Page 46

F5100 / F5105 / F5110 / F5115 User Manual

8.3.5 Bonjour

Bonjour, also known as zero-configuration networking, enables automatic discovery of computers, devices, and services on IP networks. Bonjour uses industry standard IP protocols to allow devices to automatically discover each other without the need to enter IP addresses or configure DNS servers.

¾ Device Name: Enter Device Name you wish.

Note: How to use Bonjour in your Windows Browser UI? Please check the link below:

http://www.apple.com/support/downloads/bonjourforwindows.html

Setting-Basic Network

Page 47

F5100 / F5105 / F5110 / F5115 User Manual

8.3.6 IP Notification

When network notify type is set to “ON”, you can send an e-mail notification of the completion of

the network setting.

¾ Notify Type: You can select the notify type among DHCP, Static IP, and PPPoE.

¾ SMTP Server Name: Type the SMTP server name up to 64 characters, or the IP address

of the SMTP server.

¾ SMTP Server Port: You can set port number from 1~65535 according to your mail server. The default value is 25.

zSecurity setting: Tick SSL box if the mail server you use has security restriction.

Note: If you use g-mail as your mail server, you should set 25 as your port number and

tick SSL box.

¾ Authentication: Select the authentication required when you send an email.

zOff: Select if no authentication is necessary when an email is sent. zOn: When authentication is necessary an e-mail is sent, there are SMPT, POP before

SMPT or both three options.

¾ SMTP: Select if SMTP authentication is necessary when an e-mail is sent. ¾ POP before SMTP: Select if POP before SMTP authentication is necessary when an

e-mail is sent.

zPOP server name: It is necessary when the POP before SMTP is selected in

Authentication. Type the POP (receiving mail) server name up to 64 characters, or type the IP address of the POP server. This setting is necessary when the SMTP server

Setting-Basic Network

Page 48

F5100 / F5105 / F5110 / F5115 User Manual

which sends e-mails performs authentication using the POP user account.

zUser name, Password: Type the user name and Password of the user who has the

mail account. This setting is necessary when the SMTP server which sends e-mails performs authentication.

¾ Recipient E-mail Address: Type the recipient e-Mail address up to 64 characters. You can specify up to three recipient E-mail addresses.

¾ Administrator Ee-mail Address: Type the Administrator e-Mail address up to 64 characters. This address is used for reply mail and sending system messages from the SMTP server.

¾ Subject: Type the subject/title of the e-Mail up to 64 characters. With respect to mail which is sent according to the IP notification.

¾ Message: Type the text of the E-mail up to 384 characters. Default value provides network information including IP, Port, MAC, Model, Firmware Version and Web Version.

8.3.7 Wireless (Only for F5105 / F5115)

The wireless network has to be set up by using cable network connection. After setting the camera correctly, the wireless function can work with cable network connection. Wireless settings must be the same as the access point or ad-hoc device. When changing the settings they should always be made first in the camera and then in the wireless access point. This ensures that the camera is always accessible when making changes.

Setting-Basic Network

Page 49

F5100 / F5105 / F5110 / F5115 User Manual

¾ Status of Wireless Network

This list is the result of network scan. The network is currently linked to will be shown in blue. The following information is provided.

zESSID - The name of a wireless network (or ad-hoc device). If the same name occurs

several times this means that several access points for that network were found. The camera cannot be configured to only associate with one particular access point.

zMode - Shows if the network type is Master (access point or router) or Ad-Hoc

(another client).

zSecurity - Shows which type of security the network uses. See below for the security

types supported by the camera.

zChannel - Shows the wireless channel currently in use. zSignal Strength - Shows the signal strength. zBit Rate - Shows the bit rate in Megabit/s. This can only be shown for the access

point currently in use. Note that the bit rate shown is the current rate, and that this value may vary over time.

¾ Wireless Setting

These settings control how the camera interacts with the wireless network. It is also possible to enable wireless encryption apart from identifying the wireless network.

zIP Address – This displays blank, 0.0.0.0 or IP Address. When it is blank, the camera

doesn’t establish physical link with access point yet. The 0.0.0.0 means that physical link was established but trying to get IP address. When it displays IP address, then user can use wireless network.

zESSID (ESSID is sometimes written as SSID.) - This is the name of the wireless

network the camera is configured for. The field accepts up to 32 alphanumeric characters. The name must be exactly the same as that used in the wireless access point or the connection will not be established.

zLeaving this field blank means the camera will attempt to access the nearest open

network.

zMode - Setting this to Managed means the camera will attempt to access the nearest

open access point. The Ad-hoc option allows the camera to connect to other wireless devices clients.

Note : 1. WPA-/WPA2-PSK (Wi-Fi Protected Access - Pre-Shared Key) the camera uses

a pre-shared key (PSK) to initiate WPA security. The pre-shared key is entered on the

access point and on each device on the wireless network. The key can be entered either

as Manual hex, as 64 hexadecimal (0-9, A-F) characters, or as a Passphrase, using 8 to

63 ASCII characters. The access point keeps out unauthorized users by requiring the

key to communicate.

2. WEP (Wired Equivalent Protection) the original security standard used in wireless

networks that provides a minimal level of security that can deter minor trespasses. The

Setting-Basic

Network

Page 50

F5100 / F5105 / F5110 / F5115 User Manual

administrator can select the key length among 64 or 128 bits. 64bits is the default

setting.

8.3.8 Messenger

Messenger function provide an easy-connect feature. User can easy to know what camera’s private and public IP address is.

¾ Protocol: support MSN only.

¾ Login Account: Camera will use this account to login MSN server. This MSN account

should be applied form http://www.msn.com.

¾ Password: password for this msn account.

¾ Re-type Password: re-type password to double confirm.

¾ Alias: This alias will display on MSN like the following which display in red frame.

¾ Port Range: Camera will select one port from this port range for video transmission.

¾ Video Mode: You can choose to receive video streaming from Computer view(MPEG-4)

Setting-Basic Network

Page 51

F5100 / F5105 / F5110 / F5115 User Manual

or Mobile view (3GPP).

¾ IP Notification: Switch the IP notification On / Off. If this feature switches On, camera will send IP notification to the users who are allowed.

¾ Privacy: Switch privacy On / Off. When privacy turns on, only those users in allow list can access the camera

¾ User: Input to this blank to edit allow list.

¾ Allow List: When privacy turns on, only those users in allow list can access the camera.

Setting-Basic Network

Page 52

F5100 / F5105 / F5110 / F5115 User Manual

8.4 Security

Click the folder of Security to display the sub folders including Account, HTTPS and IP

Filter.

8.4.1 Account

The device fault account and password setting is “admin / admin”. That means everyone who knows IP address can access the device including all configuration. It is necessary to assign a password if the device is intended to be accessed by others.

¾ User name: Set a user name between 4-16 characters.

¾ Password: Set a password between 4-16 characters.

¾ Re-type Password: Re-type the password to confirm.

¾ Viewer Mode: Set the user mode among Admin, Operator, and Viewer. Different viewer

mode has different limits of authority.

zThe Admin mode has all authority of configuration. zThe Operator mode can not only view the Live View but also control the PTZ (only

for PTZ models).

zThe Viewer mode only can view the Live View.

¾ Viewer Authentication: Select On, allows any viewer direct access to Live View. Select

Off, allow admin, operator, or viewer access to Live View.

Setting-Basic Security

Page 53

F5100 / F5105 / F5110 / F5115 User Manual

8.4.2 HTTPS

HTTPS is a URI scheme used to indicate a secure HTTP connection. It is syntactically

identical to the http:// scheme normally used for accessing resources using HTTP. Using an https: //URL/ with a different default TCP port (443) and an additional encryption / authentication layer between the HTTP and TCP. You can use the IP camera through HTTPS easily by using https:// instead of http://.

¾ Create & Install: Create a self-signed certificate for HTTPS to recognize.

¾ Installed Certificate: Display or remove the properties of the installed certificate.

¾ HTTPS Connection Policy: Set HTTPS connection policy for different level of users.

¾ To use the HTTPS encryption, please set up “Create self-signed certificate” for the first

time you use the HTTPS function, and then set up the connection policy for different users.

Note: When enable HTTPS with RTSP on mode, the IP Camera only protect the setting such

as username and password and do not protect video and audio. When enable HTTPS with

RTSP off mode, the IP Camera will protect all setting including video and audio.

Setting-Basic Security

ʳʳ

Page 54

F5100 / F5105 / F5110 / F5115 User Manual

8.4.3 IP Filter

IP Filter provides the function of controlling the range of IP address, similar with firewall service.

¾ IP Filter: Select if you would like to have IP filter function.

¾ Allow Range: The default range is from 0.0.0.0 to 255.255.255.255. Enter the “Start IP

address” and “End IP address” in the range, then you can add a new allow range in allow range list.

¾ Allow Range List: Except the default range 0.0.0.0~255.255.255.255, the list allows to

add four more sets of allow range at most.

¾ Deny Range: You can define the deny range by entering “Start IP address” and “End IP

address”

¾ Deny Range List: You can define not more than five sets of deny range in the list.

Setting-Basic Security

Page 55

F5100 / F5105 / F5110 / F5115 User Manual

Chapter 9. Setting-Advanced

Click the folder of Advanced to display the sub folders including FTP client, SMTP, Network

Storage, HTTP Event, Alarm Output, Schedule, Alarm Input, Alarm Buffer, Motion

Detection, Audio Detection, and System Log.

9.1 FTP Client

Use this menu to set up for capturing and sending a image or video clip to an FTP server. By using FTP client function, you can send files which has been shot and recorded linked with the external sensor input or with the built-in motion detection function to FTP server. FTP client setting menu is composed of two tabs, General, Alarm Sending and Periodical

Sending.

9.1.1 General

Select On when you use FTP function. The FTP client Setting screen appears. Select Off, when you do not wish to use the FTP client function.

Note: The frame rate and operability on the main viewer may decrease while a file is

being transmitted by the FTP client function.

¾ FTP Server Name: Type the FTP server name to upload still images up to 64 characters,

or the IP address of the FTP server.

¾ User Name: Type the user name for the FTP server.

Setting-Advanced FTP Client

Page 56

F5100 / F5105 / F5110 / F5115 User Manual

¾ Password: Type the password for the FTP server.

¾ Retype Password: To confirm the password, type the same characters as you typed in the

Password box.

¾ Passive Mode: Set whether you use the passive mode of FTP server or not when

connecting to FTP server. Select On to connect to FTP server using the passive mode.

¾ Attached File Type: You can choose snapshot or video clip for alarm sending. Select

“Snapshot,” one snapshot will be transmitted to the specified FTP server while motion detection / audio detection / alarm input triggered. Select “Video clip,” one 5-seconds video clip will be transmitted.

¾ Test: After setting the FTP server information, you can tick the test key to test if the

connection between IP CAM and FTP server works.

9.1.2 Alarm Sending

Set to forward a snapshot or video clip file to the specified FTP server linked with the alarm detection by the external sensor input or by the built-in motion detection function. Select On to send the file to FTP server linked with the alarm detection.

¾ Remote Path: Type the path to the destination in FTP server up to 64 characters.

¾ Image File Name: Type the file name you want to assign to the files when sending to the

FTP server. You can use up to 10 alphanumeric characters, - (hyphen) and _ (underline) for naming.

Setting-Advanced FTP Client

Page 57

F5100 / F5105 / F5110 / F5115 User Manual

¾ Suffix: Select a suffix to add to the file name

zDate & time: The date & time suffix is added to the Image file name. The date/time

suffix consists of lower two-digits of year (2 digits), month (2 digits), date (2 digits), hour (2 digits), minute (2 digits), second (2 digits), and consecutive number (2 digits), thus 14-digit number is added to the file name.

zSequence number: A consecutive number of 10 digits between 1 and 4294967295

and two fixed digits 00 is added to the Image file name.

zSequence number clear: Click Clear and the suffix of the sequence number returns

to 1.

¾ Alarm

zMotion detection: Click it on for using Motion detection function as a sensor. You

can set motion detection function at the motion detection function screen.

Note: You can set motion detection at motion detection screen. (Please go “Setting ĺ

Advanced ĺMotion detection ĺ Setting”) For more details, you can check Chapter 9.9.

zAudio detection: Click it on for using Audio detection function as a sensor. You can

set audio detection function at the audio detection function screen.

Note: You can set audio detection at audio detection screen. (Please go “Setting ĺ

Advanced ĺAudio detection ĺ Setting”) For more details, you can check Chapter 9.10.

zNetwork link down: Click it on to receive a snapshot or a video clip while network

link down. If Attached file type (go “Setting ĺ Advanced ĺ FTP client ĺ General”) was clicked as video clip, you can using Alarm buffer function as a sensor. It’s for recording audio file in the IP CAM before and after disconnected network.

Note: You can set alarm buffer at alarm buffer screen. (Please go “Setting ĺ Advanced ĺ

Alarm buffer ĺ Setting”) For more details, you can check Chapter 9.8.

zAlarm Input: Select the connected alarm. Sensor input1: The external sensor which

is connected to sensor input1 of the alarm input.

Note: You can set the alarm input function at alarm input screen. (Please go “Setting ĺ

Advanced ĺ Alarm input ĺ Setting”). For more details, you can check Chapter 9.7.

¾ Effective Period: Set the period when the periodical sending is effective.

zAlways: The periodical sending is always effective. zSchedule: You can specify the period when the periodical sending is effective in the

Schedule setting in the other section.

Note: You can set schedule function at schedule screen. (Please go “Setting ĺ Advanced

ĺ Schedule ĺ Setting”) For more details, you can check Chapter 9.6.

Setting-Advanced

FTP Client

Page 58

F5100 / F5105 / F5110 / F5115 User Manual

9.1.3 Periodical Sending

Select On, you can set to send an image file to FTP server periodically.

¾ Remote Path: Remote path: Type the path to storage location of FTP server which you

have authorized.

¾ Image File Name: Type the file name of snapshot or video clip sent by SMTP up to 10

alphanumeric characters, - (hyphen) and _ (under score).

¾ Suffix: Select a suffix to be added to the file name sent by SMTP.

zNone: The name of the sent file will be the Image file name. zDate & time: The date & time suffix is added to the Image file name. The date & time

suffix consists of lower two-digits of year (2 digits), month (2 digits), date (2 digits), hour (2 digits), minute (2 digits) and second (2 digits), and consecutive number (2 digits), thus 14-digit number is added to the file name.

zSequence number: A consecutive number is added to the Image file name. zSequence number clear: Click Clear and the suffix of the sequence number returns

to 1.

¾ Interval: Set the periodical sending is effective interval. Min value is 1 min and Max value is 24 hour.

¾ Effective Period: Set the period when the periodical sending is effective.

zAlways: The periodical sending is always effective. zSchedule: You can specify the period when the periodical sending is effective in the

schedule setting in the other section. Please check “Setting ĺ Advanced ĺ Schedule ĺSetting”.

Note: You can set schedule function at schedule screen. (Please go “Setting ĺ Advanced

ĺ Schedule ĺ Setting”) For more details, you can check Ch

Setting-Advanced

apter 9.6.

FTP Client

Page 59

F5100 / F5105 / F5110 / F5115 User Manual

9.2 SMTP

Set the SMTP menu when you want to send an image or video clip via e-mail. By using Mail (SMTP) function, you can send a mail with attached file which has been shot linked with the external sensor input or with the built-in motion detection function. The file can also be sent periodically. E-Mail (SMTP) setting menu is composed of three tabs, General,

Alarm sending and Periodical sending.

9.2.1 General

Select On when you use the SMTP function. The common setting options are displayed below. Select Off, if you do not wish to use the e-Mail (SMTP) function.

Note : The Setting of general part will be the same as IP Notification. (Please check “Setting ĺ

Basic ĺ Network ĺ IP Notification”)

¾ SMTP Server Name: Type the SMTP server name up to 64 characters, or the IP address of the SMTP server.

¾ SMTP Server Port: You can set port number from 1~65535 according to your mail

server. The default value is 25.

zSecurity setting: Tick SSL box if the mail server you use has security restriction.

Setting-Advanced SMTP

Page 60

F5100 / F5105 / F5110 / F5115 User Manual

Note: If you use g-mail as your mail server, you should set 25 as your port number and

tick SSL box.

¾ Authentication: Select the authentication required when you send an email.

zOff: Select if no authentication is necessary when an email is sent. zOn: When authentication is necessary an e-mail is sent, select one of the

authentication methods from the followings.

¾ SMTP: Select if SMTP authentication is necessary when an e-mail is sent. ¾ POP before SMTP: Select when POP before SMTP authentication is necessary when an

e-mail is sent.

NoteΚWhen you set to On, be sure to select either or both SMTP or / and POP before SMTP.

zPOP server name: It is necessary when the POP before SMTP is selected in

Authentication. Type the POP (receiving mail) server name up to 64 characters, or type the IP address of the POP server. This setting is necessary when the SMTP server which sends e-mails performs authentication using the POP user account.

zUser name, Password: Type the user name and Password of the user who has the

mail account. This setting is necessary when the SMTP server which sends e-mails performs authentication.

¾ Recipient Ee-mail Address: Type the recipient e-Mail address up to 64 characters. You can specify up to three recipient E-mail addresses.

¾ Administrator E-mail Address: Type the Administrator e-Mail address up to 64

characters. This address is used for reply mail and sending system messages from the SMTP server.

¾ Attached File Type: You can choose snapshot or video clip for alarm sending. Select

“Snapshot,” one snapshot will be transmitted to the administrator’s e-mail address while motion detection / audio detection / alarm input triggered. Select “Video Clip,” one 5-seconds video clip will be transmitted.

¾ Subject: Type the subject/title of the e-Mail up to 64 characters. With respect to mail

which is sent according to the alarm detection when Alarm sending of the alarm tab is set to On, the characters standing for the sensor type added to the subject.

¾ Message: Type the text of the E-mail up to 384 characters. (A line break is equivalent to 2

characters.)

¾ Test: After setting the SMPT server information, you can tick the test key to test if the

connection between IP CAM and the SMPT server works.

Setting-Advanced

SMTP

Page 61

F5100 / F5105 / F5110 / F5115 User Manual

9.2.2 Alarm Sending

Set to send the mail with connection to the alarm detection by the external sensor input or by the built-in motion detection function. Select On to send the image file to SMTP server linked with the alarm detection.

¾ Alarm Sending: Select On to set to send mail with connection to the alarm detection.

¾ File Attachment: Set whether an image file is attached to the mail sent or not. When On

is selected, the image file made by the settings below is attached. When Off is selected, only the message is sent.

¾ Image File Name: Type the file name you want to assign to the file attached to a mail.

You can use up to 10 alphanumeric, - (hyphen) and _ (underscore) for naming.

¾ Suffix: Select a suffix to add to the file name

zNone: The name of the sent file will be the Image file name. zDate & time: The date & time suffix is added to the Image file name. The date & time

zSequence number: A consecutive number is added to the Image file name. zSequence number clear: Click Clear and the suffix of the sequence number returns

to 1.

Setting-Advanced

SMTP

Page 62

F5100 / F5105 / F5110 / F5115 User Manual

¾ Alarm

zMotion Detection: Click it on for using Motion Detection function as a sensor. You

can set motion detection function at the motion detection function screen.

Note: You can set motion detection at motion detection screen. (Please go “Setting ĺ

Advanced ĺ Motion detection ĺ Setting”) For more details, you can check Chapter 9.9.

zAudio detection: Click it on for using Audio detection function as a sensor. You can

set audio detection function at the audio detection function screen.

Note: You can set audio detection at audio detection screen. (Please go “Setting ĺ

Advanced ĺAudio detection ĺ Setting”) For more details, you can check Chapter 9.10.

zNetwork link down: Click it on to receive a snapshot or a video clip while network

Note: You can set alarm buffer at alarm buffer screen. (Please go “Setting ĺ Advanced

ĺ Alarm buffer ĺ Setting”) For more details, you can check Chapter 9.8.

zAlarm Input: Select the connected alarm. Sensor input1: The external sensor which

is connected to sensor input1 of the alarm input.

Note: You can set the alarm input function at alarm input screen. (Please go “Setting ĺ

Advanced ĺ Alarm input ĺ Setting”). For more details, you can check Chapter 9.7.

¾ Effective Period: Set the period when the periodical sending is effective.

zAlways: The periodical sending is always effective. zSchedule: You can specify the period when the periodical sending is effective in the

Schedule setting in the other section.

Note: You can set schedule function at schedule screen. (Please go “Setting ĺ Advanced

ĺ Schedule ĺ Setting”) For more details, you can check Chapter 9.6.

9.2.3 Periodical Sending

You can set to send an image file by SMTP server periodically by selecting On to send the image file by SMTP server linked with setting period.

Setting-Advanced

SMTP

Page 63

F5100 / F5105 / F5110 / F5115 User Manual

¾ Image File Name: Type the file name of the image sent by SMTP up to 10 alphanumeric

characters, - (hyphen) and _ (under score).

¾ Suffix: Select a suffix to be added to the file name sent by SMTP.

zDate & time: The date & time suffix is added to the Image file name. The date & time

zSequence number: A consecutive number is added to the Image file name. zSequence number clear: Click Clear and the suffix of the sequence number returns

to 1.

¾ Interval: Set the periodical sending is effective interval. Min value is 1 min and Max

value is 24 hour.

¾ Effective Period: Set the period when the periodical sending is effective.

zAlways: The periodical sending is always effective. zSchedule: You can specify the period when the periodical sending is effective in the

schedule setting in the other section. Please check “Setting ĺ Basic ĺ Advanced

ĺ Schedule ĺ Setting.”

Note: You can set schedule function at schedule screen. (Please go “Setting ĺ Advanced ĺ Schedule ĺ Setting”) For more details, you can check Chapter 9.6.

Setting-Advanced

SMTP

Page 64

F5100 / F5105 / F5110 / F5115 User Manual

9.3 Network Storage

Network storage provides the storage function for saving video clip to the specified computer and folder connected with the operating computer.

9.3.1 General

Select On if you would like to use the network storage function. Then choose one protocol between Windows network (SMB/CIFS) and Unix network (NFS).

¾ Protocol - Windows Network (SMB/CIFS):.

zNetwork Storage Location: Type the IP or name of specified computer and folder.

For example, //IP/folder name or // my_nas/folder name.

zWorkgroup: Type the name of workgroup which the operating computer belongs. zUser Name & Password: Type the name and password for workgroup. zAttached File Type: You can choose snapshot or video clip for alarm sending. Select

“Snapshot,” one snapshot will be transmitted to the specified network storage location while motion detection / audio detection / alarm input triggered. Select “Video clip,” one video clip which can be selected from 5 seconds to 60 seconds will be transmitted.

zTest: After setting the network storage location information, you can tick the test key

to test if the connection between IP CAM and network storage location works.

¾ Protocol- Unix network (NFS):

zNetwork Storage Location: Type the IP or name of specified computer and folder.

For example, //IP/folder name or my_nas:/folder name.

zTest: After setting the network storage location information, you can tick the test key

to test if the connection between IP CAM and network storage location works.

Setting-Advanced

Network Storage

Page 65

F5100 / F5105 / F5110 / F5115 User Manual

Note: If the recording video file is assigned to be stored in a low-speed device (ex.

low-speed USB storage disk), there might be some problems to complete the storage.

9.3.2 Alarm sending

Set to transmit the video clip file with connection to the alarm detection by the external sensor input or by the built-in motion detection function. Select On to send the file to network storage location linked with the alarm detection.

¾ Alarm sending: Select On to set to send mail with connection to the alarm detection.

¾ Image file name: Type the file name you want to assign to the file to attach a mail. You

can use up to 10 alphanumeric, - (hyphen) and _ (underscore) for naming.

¾ Suffix: Select a suffix to add to the file name

zDate time: The date & time suffix is added to the Image file name. The date & time

zSequence number: A consecutive number is added to the Image file name. zSequence number clear: Click Clear and the suffix of the sequence number returns

to 1.

¾ Alarm:

zMotion Detection: Click it on for using Motion Detection function as a sensor. You

can set motion detection function at the motion detection function screen.

Note: You can set motion detection at motion detection screen. (Please go “Setting ĺ

Setting-Advanced Network Storage

Page 66

F5100 / F5105 / F5110 / F5115 User Manual

Advanced ĺ Motion detection ĺ Setting”) For more details, you can check Chapter 9.9.

zAudio detection: Click it on for using Audio detection function as a sensor. You can

set audio detection function at the audio detection function screen.

Note: You can set audio detection at audio detection screen. (Please go “Setting ĺ

Advanced ĺAudio detection ĺ Setting”) For more details, you can check Chapter 9.10.

zNetwork link down: Click it on to receive a video clip while network link down. It’s

for recording video file in the IP CAM before and after disconnected network.

Note: You can set alarm buffer at alarm buffer screen. (Please go “Setting ĺ Advanced ĺ

Alarm buffer ĺ Setting”) For more details, you can check Chapter 9.8.

zAlarm input: Select the connected alarm. Sensor input1: The external sensor which

is connected to sensor input1 of the alarm input.

Note: You can set the alarm input function at alarm input screen. (Please go “Setting ĺ Advanced ĺ Alarm input ĺ Setting”). For more details, you can check Chapter 9.7.

¾ Effective period: Set the period when the periodical sending is effective.

zAlways: The periodical sending is always effective. zSchedule: You can specify the period when the periodical sending is effective in the

Schedule setting in the other section.

Note: You can set schedule function at schedule screen. (Please go “Setting ĺ Advanced

ĺ Schedule ĺ Setting”) For more details, you can check Chapter 9.6.

9.3.3 Periodical recording

Setting-Advanced Network Storage

Page 67

F5100 / F5105 / F5110 / F5115 User Manual

You can set up to transmit image files to the network storage location periodically by selecting On.

¾ Image file name: Type the file name you want to assign to the file transmitted to the

network storage location. You can use up to 10 alphanumeric, - (hyphen) and _ (underscore) for naming.

¾ Suffix: Select a suffix to add to the file name

zDate & time: The date & time suffix is added to the Image file name. The date & time

zSequence number: A consecutive number is added to the Image file name. zSequence number clear: Click Clear and the suffix of the sequence number returns

to 1.

¾ File Size: The file size of image or video clip transmitted to the network storage location

can’t over 50MB.

¾ Cyclic Size: The total amount of files transmitted to the network storage location has to

be in the range from 100 to 1024000MB.

¾ Recording Time: Set the period when the periodical recording is effective.

zAlways: The periodical recording is always effective. zSchedule: You can specify the period when the periodical recording is effective in the

Schedule setting in the other section.

Note: You can set schedule function at schedule screen. (Please go “Setting ĺ Advanced

ĺ Schedule ĺ Setting”) For more details, you can check Chapter 9.6.

Setting-Advanced Network Storage

Page 68

F5100 / F5105 / F5110 / F5115 User Manual

9.4 HTTP Event

Set up this menu for sending commands to an HTTP server. By using HTTP client function, you can send the command defined by yourself, linked with the external sensor input or with the built-in motion detection function to HTTP server. HTTP client setting menu is composed of two tabs, General and Alarm sending.

9.4.1 General

¾ HTTP event: Set up the HTTP server URL, port, User ID, Password, and Proxy server

settings.

For example: URL: 192.168.1.7/cgi-bin/operator/ptzset

Note: The setting of URL should be the same as CGI.

Setting-Advanced HTTP Event

Page 69

F5100 / F5105 / F5110 / F5115 User Manual

9.4.2 Alarm Sending

Set to send the command with connection to the alarm detection by the external sensor input or by the built-in motion detection function. Select “On“ to send the command to HTTP server linked with the alarm detection.

Alarm sending: Select On to set to send command with connection to the alarm detection.

¾ Alarm

zMotion Detection: Click it on for using Motion Detection function as a sensor. You

can set motion detection function at the motion detection function screen.

Note: You can set motion detection at motion detection screen. (Please go “Setting ĺ

Advanced ĺ Motion detection ĺ Setting”) For more details, you can check Chapter 9.9.

9 Parameter: the parameter of CGI (defined in URL of HTTP ĺ General) is

from your target device. For example, move=down.

9 Message: message will show up in the form of Message = PTZ down. If your

target device didn’t support the parameter of message, you can’t see the message. So you can just take the message as a note. For example: PTZ down.

Setting-Advanced HTTP Event

Page 70

F5100 / F5105 / F5110 / F5115 User Manual

zAudio Detection: Click it on for using Audio detection function as a sensor. You can

set audio detection function at the audio detection function screen.

Note: You can set audio detection at audio detection screen. (Please go “Setting ĺ

Advanced ĺAudio detection ĺ Setting”) For more details, you can check Chapter 9.10.

9 Parameter: the parameter of CGI (defined in URL of HTTP ĺ General) is

from your target device. For example, move=down.

9 Message: message will show up in the form of Message = PTZ down. If your

target device didn’t support the parameter of message, you can’t see the message. So you can just take the message as a note. For example: PTZ down.

zNetwork link down: Click it on to send a message to the specified HTTP server

while network link down.

9 Parameter: the parameter of CGI (defined in URL of HTTP ĺ General) is

from your target device. For example, move=down.

9 Message: message will show up in the form of Message = PTZ down. If your

target device didn’t support the parameter of message, you can’t see the message. So you can just take the message as a note. For example: PTZ

Setting-Advanced

HTTP Event

Page 71

F5100 / F5105 / F5110 / F5115 User Manual

down.

zAlarm Input: Select the connected alarm. Sensor input 1: The external sensor which

is connected to sensor input1 of the alarm input.

Note: You can set the alarm input function at alarm input screen. (Please go “Setting ĺ

Advanced ĺ Alarm Input ĺ Setting”). For more details, you can check Chapter 9.7.

9 Parameter: the parameter of CGI (defined in URL of HTTP ĺ General) is

from your target device. For example, move=down.

9 Message: message will show up in the form of Message = PTZ down. If your

target device didn’t support the parameter of message, you can’t see the message. So you can just take the message as a note. For example: PTZ down.

¾ Effective Period: Set the period when the periodical sending is effective.

zAlways: The periodical sending is always effective. zSchedule: You can specify the period when the periodical sending is effective in the

schedule setting in the other section.

Note: You can set schedule function at schedule screen. (Please go “Setting ĺ Advanced

ĺ Schedule ĺ Setting”) For more details, you can check Chapter 9.6.

Setting-Advanced HTTP Event

Page 72

F5100 / F5105 / F5110 / F5115 User Manual

9.5 Alarm Output

You can set Alarm Output function in this menu to control the alarm out of I / O port on the rear of the device linked to the alarm detection and the timer.

¾ Alarm Output: To activate the Alarm output function, select On. If not, select Off. ¾ Digital Output: Select High signal output and Low signal output as your alarm. ¾ Trigger Condition: Select the mode of the Alarm output function. You can choose

“Alarm” or “Timer”.

¾ Alarm: Controls alarm output by synchronizing with an external sensor input or the built-in

activity detection function.

zMotion Detection: Click it on for using Motion Detection function as a sensor. You

can set motion detection function at the motion detection function screen.

Note: You can set motion detection at motion detection screen. (Please go “Setting ĺ

Advanced ĺ Motion Detection ĺ Setting”) For more details, you can check Chapter 9.9.

zAudio detection: Click it on for using Audio Detection function as a sensor. You can

set audio detection function at the audio detection function screen.

Note: You can set audio detection at audio detection screen. (Please go “Setting ĺ

Setting-Advanced Alarm Output

Page 73

F5100 / F5105 / F5110 / F5115 User Manual

Advanced ĺAudio Detection ĺ Setting”) For more details, you can check Chapter 9.10.

zNetwork link down: Click it on to output voltage 12 V to activate alarm output

function while network link down.

Note: You can set alarm buffer at alarm buffer screen. (Please go “Setting ĺ Advanced

ĺ Alarm Buffer ĺ Setting”) For more details, you can check Chapter 9.8.

zAlarm Input: Select the connected alarm. Sensor Input: The external sensor which

is connected to sensor input1 of the alarm input.

Note: You can set the alarm input function at alarm input screen. (Please go “Setting ĺ

Advanced ĺ Alarm Input ĺ Setting”) For more details, you can check Chapter 9.7.

¾ Alarm Duration: There are up to 60 second options to choose for alarm duration interval. ¾ Effective Period: Set the period when the periodical sending is effective.

zAlways: The periodical sending is always effective. zSchedule: You can specify the period when the periodical sending is effective in the

Schedule setting in the other section.

Note: You can set schedule function at schedule screen. (Please go “Setting ĺ Advanced

ĺ Schedule ĺ Setting”) For more details, you can check Chapter 9.6.

Setting-Advanced Alarm Output

Page 74

F5100 / F5105 / F5110 / F5115 User Manual

9.6 Schedule

Click Schedule on the Advanced mode menu, the Schedule setting menu appears. This is the same menu as the setting menu which is displayed when you click Schedule to set Effective Period and Schedule in FTP client, E-mail (SMTP), HTTP event, Record, and Alarm Out setting menu setting menu.

¾ Schedule Selection: Select the list box to specify the schedule you want to set.

zFTP -Alarm / FTP – Periodical / E-mail (SMTP) -Alarm / E-mail

(SMTP) –Periodical / HTTP Event -Alarm / Record –Alarm / Record –Periodical / Alarm Output- Alarm / Alarm Output- Timer

¾ Mon (Monday) to Sun (Sunday): The time period on the right of the checked day is the

effective period of the schedule.

¾ Start time, End time: Specify the Start Time and the End Time.

¾ Use the same time schedule every day: When this is checked, the Start Time and End

Time set to Mon (Monday) are applied to all days. In this case, the Start Time and End Time of the other days than Mon (Monday) cannot be input.

Setting-Advanced Schedule

Page 75

F5100 / F5105 / F5110 / F5115 User Manual

9.7 Alarm Input

When you click Alarm Input on the Advanced mode menu, the Alarm Input setting menu appears. You can set in this menu to control the external alarm input of I / O port on the rear of the device linked to FTP, SMTP, Network Storage, and HTTP Event.

¾ Sensor Input 1: Click it on for using external sensor which is connected to sensor

input1 of the camera I / O port.

¾ Trigger Condition: Select High signal output and Low signal output as your alarm. ¾ Camera Move: Pull down the window to select the camera preset position.

Setting-Advanced Alarm Input

Page 76

F5100 / F5105 / F5110 / F5115 User Manual

9.8 Alarm Buffer

When you click Alarm Buffer on the Advanced mode menu, the Alarm buffer setting menu appears. You can set in this menu to enable alarm buffer function connected with FTP Client,

and SMTP.

Use alarm buffer function for recording audio and video file in the IP Camera before and after disconnected network. After re-connecting, these files will transmit to FTP Client, and SMTP. You can set the pre-alarm and post-alarm period up to 5 seconds in Alarm Buffer function screen.

Setting-Advanced Alarm Buffer

Page 77

F5100 / F5105 / F5110 / F5115 User Manual

9.9 Motion Detection

There are three Motion Detection functions as sensors to set for different detecting zones. Each one has Threshold and Sensitivity inputs which you can adjust to specific zone sequentially. Motion Detection function can support to FTP Client, SMTP, Network

Storage, HTTP Event, and Alarm Output.

¾ Threshold: It means the extent which the alarm will be triggered. The default value is 50

and the value range is 0~100.

¾ Sensitivity: It means that how often the sensor will scan the image different. The higher

sensitivity it is and the more frequently it scans. The default value is 50 and the value range is 0~100.

zMotion detection 1: Click it on for using Motion detection 1 function as a sensor.

You can adjust and move the detecting zone by using mouse.

zMotion detection 2: Click it on for using Motion detection 2 function as a sensor.

You can adjust and move the detecting zone by using mouse.

zMotion detection 3: Click it on for using Motion detection 3 function as a sensor.

You can adjust and move the detecting zone by using mouse.

Setting-Advanced Motion Detection

Page 78

F5100 / F5105 / F5110 / F5115 User Manual

9.10 Audio Detection

The Audio detection has Threshold and Sensitivity inputs which you can adjust sequentially. Audio Detection function can support to FTP Client, SMTP, Network Storage, HTTP Event, Alarm Output and so on.

Click it on for using Audio detection function as a sensor. You can set audio detection function at the audio detection function screen.

¾ Threshold: It means the extent which the alarm will be triggered. The default value is 50

and the value range is 0~100.

¾ Sensitivity: It means that how often the sensor will scan the image different. The higher

sensitivity it is and the more frequently it scans. The default value is 5 and the value range is 1~10.

Setting-Advanced Audio Detection

Page 79

F5100 / F5105 / F5110 / F5115 User Manual

9.11 System Log

The System Log function allows users to review any changes and events happened. The system starts logging automatically after started.

¾ Enable remote log: Enables user to send the log data to a specified log server.

Setting-Advanced System Log

Page 80

F5100 / F5105 / F5110 / F5115 User Manual

CHAPTER 10. APPENDIX

A. Frame-rate and Bitrate Table – Help to set IPCamera with your network

environment to access Internet.

Base on your network upload environment to choose the suitable Image-Quality setting. For example, if the network environment is ADSL 256Kb(upload) / 2Mb(download), the most fluent Image-Quality needs to set up under 256 Kb situation.

A.1 Mega Mode

A.1.1. H.264 @ 15fps / kbps

Quality 1280*1024 1280*720 640*480 320*240

Excellent

Detailed

Good

Standard

Medium

1500 1200 180 50

400 250 100 30 250 100 80 20 100 60 50 15

80 50 40 10

A.1.2. H.264 @ 10fps / kbps

Quality 1280*1024 1280*720 640*480 320*240

Excellent

Detailed

Good

Standard

Medium

A.1.3. H.264 / kbps, fps

Image-Size Bitrate Setting

1280*1024 6144 15 1280*1024 6144 10 1280*1024 2048 15 1280*1024 2048 10 1280*1024 512 15 1280*1024 512 10

1280*720 6144 15 1280*720 6144 10 1280*720 2048 15 1280*720 2048 10 1280*720 512 15 1280*720 512 10

1000 800 120 30

280 100 70 20 170 70 55 15

70 40 30 10 55 30 20 8

Frame-Rate

Setting

Current Bitrate

6300 15 6300 10 2200 15 2200 10

550 15

550 10 6300 15 6300 10 2200 15 2200 10

550 15

550 10

Current

Frame-Rate

Page 81

640*480 6144 15 640*480 6144 10 640*480 2048 15 640*480 2048 10 640*480 512 15 640*480 512 10 320*240 6144 15 320*240 6144 10 320*240 2048 15 320*240 2048 10 320*240 512 15 320*240 512 10

A.1.4. MPEG 4@ 15fps / kbps

Quality 1280*1024 1280*720 640*480 320*240

Excellent

Detailed

Good

Standard

Medium

2700 2000 300 100 1100 800 200 80

500 350 150 60 350 250 100 40 300 200 80 35

F5100 / F5105 / F5110 / F5115 User Manual

6300 15 6300 10 2200 15 2200 10

550 15

550 15 5100 15 3600 10 2200 15 2200 10

550 15

550 10

A.1.5. MPEG4@ 10fps / kbps

Quality 1280*1024 1280*720 640*480 320*240

Excellent

Detailed

Good

Standard

Medium

1800 1400 200 80

800 550 120 60 350 250 100 40 250 180 80 30 200 140 60 25

A.1.6. MPEG4 / kbps, fps

Image-Size Quality Setting

1280*1024 6144 15 1280*1024 6144 10 1280*1024 2048 15 1280*1024 2048 10 1280*1024 512 15 1280*1024 512 10

1280*720 6144 15 1280*720 6144 10 1280*720 2048 15 1280*720 2048 10 1280*720 512 15 1280*720 512 10

640*480 6144 15 640*480 6144 10 640*480 2048 15 640*480 2048 10

Frame-Rate

Setting

Current Bitrate

5500 13 6300 10 2200 15 2200 10

550 15

550 10 6300 15 6300 10 2200 15 2200 10

550 15

550 10 6300 15 6300 10 2200 15 2200 10

Current

Frame-Rate

Page 82

640*480 512 15 640*480 512 10 320*240 6144 15 320*240 6144 10 320*240 2048 15 320*240 2048 10 320*240 512 15 320*240 512 10

A.1.7. MJPEG @ 15fps / kbps

Quality 1280*1024 1280*720 640*480 320*240

Excellent

Detailed

Good

Standard

Medium

22000 16000 6000 2200 12000 7000 3000 1200

7000 5000 2500 1000 5500 4000 2000 800 4000 3000 1200 500

A.1.8. MJPEG@ 10fps / kbps

Quality 1280*1024 1280*720 640*480 320*240

Excellent

Detailed

Good

Standard

Medium

15000 11000 4000 1500

8000 5000 2000 800 5000 3500 1800 700 4000 3000 1500 600 3000 2000 800 350

F5100 / F5105 / F5110 / F5115 User Manual

550 15

550 10 2200 15 1800 10 2200 15 1800 10

550 15

550 10

A.1.9. MJPEG / kbps, fps

Image-Size Quality Setting

1280*1024 Excellent 15 1280*1024 Excellent 10 1280*1024 Good 15 1280*1024 Good 10 1280*1024 Medium 15 1280*1024 Medium 10

1280*720 Excellent 15 1280*720 Excellent 10 1280*720 Good 15 1280*720 Good 10 1280*720 Medium 15 1280*720 Medium 10

640*480 Excellent 15 640*480 Excellent 10 640*480 Good 15 640*480 Good 10 640*480 Medium 15 640*480 Medium 10 320*240 Excellent 15 320*240 Excellent 10

Frame-Rate

Setting

Current Bitrate

22000 15 15000 10

7000 15 5000 10 4000 15 3000 10

16000 15 11000 10

5000 15 3500 10 3000 15 2000 10 6000 15 4000 10 2500 15 1800 10 1200 15

800 10 2200 15 1500 10

Current

Frame-Rate

Page 83

320*240 Good 15 320*240 Good 10 320*240 Medium 15 320*240 Medium 10

A.2 VGA Mode

A.2.1 H.264 @ 30fps / kbps

Quality 640*480 320*240

Excellent

Detailed

Good

Standard

Medium

A.2.2 H.264@15 fps / kbps

Quality 640*480 320*240

Excellent

Detailed

Good

Standard

Medium

F5100 / F5105 / F5110 / F5115 User Manual

1000 15

700 10

500 15

350 10

600 60 120 40

60 30 50 25 40 20

400 40

80 30 40 25 30 20 25 15

A.2.3 H.264 / kbps, fps

Image-Size Bitrate Setting

640*480 6144 30 640*480 6144 15 640*480 2048 30 640*480 2048 15 640*480

640*480 512 15 320*240 6144 30 320*240 6144 15 320*240 2048 30 320*240 2048 15 320*240 512 30 320*240 512 15

A.2.4 MPEG4 @ 30fps / kbps

Quality 640*480 320*240

Excellent

Detailed

Good

Standard

Medium

Frame-Rate

Setting

512 30

1000 120

400 80 200 60 150 50 120 40

Current Bitrate

6300 30 6300 15 2200 30 2200 15

550 30

550 15 6300 30 5500 15 2200 30 2200 15

550 30

550 15

Current

Frame-Rate

Page 84

A.2.5 MPEG4@ 15fps / kbps

Quality 640*480 320*240

Excellent

Detailed

Good

Standard

Medium

A.2.6 MPEG4 / kbps, fps

Image-Size Bitrate Setting

640*480 6144 30 640*480 6144 15 640*480 2048 30 640*480 2048 15 640*480 512 30 640*480 512 15 320*240 6144 30 320*240 6144 15 320*240 2048 30 320*240 2048 15 320*240 512 30 320*240 512 15

F5100 / F5105 / F5110 / F5115 User Manual

600 80 250 50 150 40 100 30

80 20

Frame-Rate

Setting

Current Bitrate

6300 30 6300 15 2200 30 2200 15

550 30

550 15 5100 30 2800 15 2200 30 2200 15

550 30

550 15

Current

Frame-Rate

A.2.7 MJPEG @ 30fps / kbps

Quality 640*480 320*240

Excellent

Detailed

Good

Standard

Medium

A.2.8 MJPEG@ 15fps / kbps

Quality 640*480 320*240

Excellent

Detailed

Good

Standard

Medium

A.2.9 MJPEG / kbps, fps

Image-Size Bitrate Setting

640*480 Excellent 30 640*480 Excellent 15 640*480 Good 30 640*480 Good 15

13000 4500

6500 2500 5000 2000 4000 1600 2500 1000

7000 2500 3500 1500 2800 1200 2100 1000 1400 700

Frame-Rate

Setting

Current Bitrate

13000 30

7000 15 5000 30 2800 15

Current

Frame-Rate

Page 85

640*480 Medium 30 640*480 Medium 15 320*240 Excellent 30 320*240 Excellent 15 320*240 Good 30 320*240 Good 15 320*240 Medium 30 320*240 Medium 15

F5100 / F5105 / F5110 / F5115 User Manual

2500 30 1400 15 4500 30 2500 15 2000 30 1200 15 1000 30

700 15

Page 86

F5100 / F5105 / F5110 / F5115 User Manual

B. Storage Requirement Table - Help to set Recording Storage System.

Please refer to the following table to find out the capability for recording into your

hard disk.

B.1 Mega Mode

B.1.1 H.264 Storage Requirement GB / channel / day @ 15fps

Quality 1280*1024 1280*720 640*480 320*240

Excellent

Detailed

Good

Standard

Medium

B.1.2 H.264 Storage Requirement GB / channel / day @ 10fps

Quality 1280*1024 1280*720 640*480 320*240

Excellent

Detailed

Good

Standard

Medium

50 45 10 4.2

16.6 13 8.3 2.5 13 8.3 6.7 1.7

8.3 5 4.2 1.3

6.7 4.2 3.4 1

45 22.5 6.7 2.5

12.5 8.3 5.9 1.7

8.3 5.9 4.6 1.3

5.9 3.4 2.5 1.3

4.5 2.5 2.1 0.7

B.1.3 MPEG4 Storage Requirement GB / channel / day

Image-Size Bitrate Setting Frame-Rate Setting Storage Requirement 1280*1024 6144 15 1280*1024 6144 10 1280*1024 2048 15 1280*1024 2048 10 1280*1024 512 15 1280*1024 512 10

1280*720 6144 15 1280*720 6144 10 1280*720 2048 15 1280*720 2048 10 1280*720 512 15 1280*720 512 10

640*480 6144 15 640*480 6144 10 640*480 2048 15 640*480 2048 10 640*480 512 15 640*480 512 10 320*240 6144 15 320*240 6144 10

522.9

182.6

45.7

522.9

182.6

45.7

522.9

182.6

45.7

423.3

298.8

Page 87

F5100 / F5105 / F5110 / F5115 User Manual

320*240 2048 15 320*240 2048 10 320*240 512 15 320*240 512 10

B.1.4 MPEG4 Storage Requirement GB / channel / day @ 15fps

Quality 1280*1024 1280*720 640*480 320*240

Excellent

Detailed

Good

Standard

Medium

133 83 25 8.3

58.1 42 17 6.7 42 25 12.5 5 30 21 8.3 3.4 25 17 6.7 3

B.1.5 MPEG4 Storage Requirement GB / channel / day @ 10fps

Quality 1280*1024 1280*720 640*480 320*240

Excellent

Detailed

Good

Standard

Medium

92 58.1 17 6.7 42 30 10 5 30 17 8.3 3.4 21 12.5 6.7 2.5 17 10 5 2

182.6

45.7

B.1.6 MPEG4 Storage Requirement GB / channel / day

Image-Size Quality Setting Frame-Rate Setting Storage Requirement 1280*1024 6144 15 1280*1024 6144 10 1280*1024 2048 15 1280*1024 2048 10 1280*1024 512 15 1280*1024 512 10

1280*720 6144 15 1280*720 6144 10 1280*720 2048 15 1280*720 2048 10 1280*720 512 15 1280*720 512 10

640*480 6144 15 640*480 6144 10 640*480 2048 15 640*480 2048 10 640*480 512 15 640*480 512 10 320*240 6144 15 320*240 6144 10 320*240 2048 15 320*240 2048 10 320*240 512 15 320*240 512 10

431.6

522.9

182.6

45.7

522.9

182.6

45.7

522.9

182.6

45.7

182.6

149.4

182.6

149.4

45.7

Page 88

F5100 / F5105 / F5110 / F5115 User Manual

B.2 VGA Mode

B.2.1. H.264 Storage Requirement GB / channel / day @ 30fps

Quality 640*480 320*240

Excellent

Detailed

Good

Standard

Medium

B.2.2. H.264 Storage Requirement GB / channel / day @ 15fps

Quality 640*480 320*240

Excellent

Detailed

Good

Standard

Medium

B.2.3. H.264 Storage Requirement GB / channel / day

Image-Size Bitrate Setting

640*480 6144 30 640*480 6144 15 640*480 2048 30 640*480 2048 15 640*480

512 30

640*480 512 15 320*240 6144 30 320*240 6144 15 320*240 2048 30 320*240 2048 15 320*240 512 30 320*240 512 15

21 5 10 3.4

5 2.5

4.2 2.1

3.4 1.7

12.5 3.4

6.7 2.5

3.4 2.1

2.5 1.7

2.1 1.3

Frame-Rate

Setting

Current Bitrate

Storage

Requirement

6300 522.9 6300 522.9 2200 182.6 2200 182.6

550

45.7

550 45.7 6300 522.9 5500 456.5 2200 182.6 2200 182.6

550 45.7

B.2.4. MPEG4 Storage Requirement GB / channel / day @ 30fps

Quality 640*480 320*240

Excellent

Detailed

Good

Standard

Medium

50 10 25 6.7

16.7 5

12.5 4.2 10 3.4

B.2.5. MPEG4 Storage Requirement GB / channel / day @ 15fps

Quality 640*480 320*240

Excellent

Detailed

Good

Standard

33.2 6.7

16.7 4.2

12.5 3.4

8.3 2.5

Page 89

Medium

6.7 1.7

B.2.6. MJPEG Storage Requirement GB / channel / day

Image-Size Bitrate Setting

Frame-Rate

Setting 640*480 6144 30 640*480 6144 15 640*480 2048 30 640*480 2048 15 640*480 512 30 640*480 512 15 320*240 6144 30 320*240 6144 15 320*240 2048 30 320*240 2048 15 320*240 512 30 320*240 512 15

F5100 / F5105 / F5110 / F5115 User Manual

Current Bitrate

Storage

Requirement

6300 522.9 6300 522.9 2200 182.6 2200 182.6

550 45.7

550 45.7 5100 423.3 2800 232.4 2200 182.6 2200 182.6

550 45.7

Page 90

F5100 / F5105 / F5110 / F5115 User Manual

C. System Requirement – Help to setup System

C.1. 16 Channel IPCamera with CIF Performance

Equipment Configuration

Software:

CPU:

Memory:

Ethernet:

Hard Disk:

Graphic card:

Operating System:

Results from Test with a Resolution of 352×240

320x240 Quality Frame Rate CPU Load Bandwidth

16 IP camera Good 20 65% 40~50 Mbps 16 IP camera Excellent 20 67% 40~50 Mbps

ˠ˴˼˖˿˸ʳ˩˸˼ʳ˅ˁˉˁˇʳˣ˹˸˼˴˿ʳ

˜˸˿ʳ˖˸ʳ˅ʳˤ˴˷ʳˤˉˉ˃˃ʳ˓ʳ˅ˇ˃˃ʳˠ˛ʳ

˄˃˅ˇʳˠ˕ʳʻ˅ʳʳˈ˄˅ʳ˗˗˥˅ˀ˦˗˥˔ˠʳʼʳ

ˠ˴˸˿˿ʳˬ˾ʳˋˋ˘ˋ˃ˈ˅ʳˣ˖˜ˀ˘ʳ˔˦˙ʳ˚˼˺˴˵˼ʳ˘˻˸˸ʳ˖˿˿˸ʳ

˦˧ˆ˅ˈ˃ˉ˅˃˔ʳʻ˅ˈ˃ʳ˚˕ʼʳ

˔˧˜ʳ˧˸˶˻˿˺˼˸ʳ˜˶ʳ˥˴˷˸ʳ˫˄ˆ˃˃ʳ˦˸˼˸ʳ

˪˼˷ʳ˫ˣʳˣ˹˸˼˴˿ʳ˦ˣ˅ʳ ʳ

C.2. 16 Channel IPCamera with D1 Performance

Equipment Configuration

Software:

CPU:

Memory:

Ethernet:

Hard Disk:

Graphic card:

Operating System:

Results from Test with a Resolution of 704×480 CCD IPCamera

704x480 Quality Frame Rate CPU Load Bandwidth

16 IP camera Excellent 30 95% 15~20 Mbps

Results from Test with a Resolution of 640×480 CMOS IPCamera

640x480 Quality Frame Rate CPU Load Bandwidth

16 IP camera Excellent 30 95% 10~15 Mbps

ˠ˴˼˖˿˸ʳ˩˸˼ʳ˅ˁˉˁˇʳˣ˹˸˼˴˿ʳ

˔ˠ˗ʳ˔˻˿ʳˉˇʽ˅ʳ˓ˆˉ˃˃ʾˠ˛ʳ

˅˃ˇˋʳˠ˕ʳʻ˅ʳʳ˄˃˅ˇʳ˗˗˥˅ˀ˦˗˥˔ˠʳʼʳ

˩˜˔ʳ˥˻˼˸ʳ˜˜ʳ˙˴ʳ˘˻˸˸ʳ˔˷˴˸ʳ

˦˧ˆ˅ˈ˃ˉ˅˃˔ʳʻ˅ˈ˃ʳ˚˕ʼʳ

˔˧˜ʳ˧˸˶˻˿˺˼˸ʳ˜˶ʳ˘˔˫˄ˉ˃˃ʳ˦˸˼˸ʳ

˪˼˷ʳ˫ˣʳˣ˹˸˼˴˿ʳ˦ˣ˅ʳˉˇʳ

Page 91

F5100 / F5105 / F5110 / F5115 User Manual

Europe – EU Declaration of Conformity

This device complies with the essential requirements of the R&TTE Directive 1999/5/EC. The following test methods have been applied in order to prove presumption of conformity with the essential requirements of the R&TTE Directive 1999/5/EC:

Clause Description EN 60950-1: 2001 EN 50392: 2004

EN 300 328 V1.6.1 (2004-11)

EN 301 489-17 V1.2.1 (2002-08) and EN 301 489-1 V1.5.1 (2004-11)

Safety of Information Technology Equipment Generic standard to demonstrate the compliance of electronic and electrical apparatus with the basic restrictions related to human exposure to electromagnetic fields (0 Hz - 300 GHz) Electromagnetic compatibility and Radio spectrum Matters (ERM); Wideband transmission systems; Data transmission equipment operating in the 2,4 GHz ISM band and using wide band modulation techniques; Harmonized EN covering essential requirements under article 3.2 of the R&TTE Directive Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 17: Specific conditions for 2,4 GHz wideband transmission systems and 5 GHz high performance RLAN equipment

This device is a 2.4 GHz wideband transmission system (transceiver), intended for use in all EU member states and EFTA countries, except in France and Italy where restrictive use applies.

In Italy the end-user should apply for a license at the national spectrum authorities in order to obtain authorization to use the device for setting up outdoor radio links and/or for supplying public access to telecommunications and/or network services.

This device may not be used for setting up outdoor radio links in France and in some areas the RF output power may be limited to 10 mW EIRP in the frequency range of 2454 – 2483.5 MHz. For detailed information the end-user should contact the national spectrum authority in France.

ýesky

[Czech]

Dansk

[Danish]

Deutsch

[German]

[Jméno výrobce] tímto prohlašuje, že tento [typ zaĜízení] je ve shodČ se základními požadavky a dalšími pĜíslušnými ustanoveními smČrnice 1999/5/ES.

Undertegnede [fabrikantens navn] erklærer herved, at følgende udstyr [udstyrets typebetegnelse] overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF.

Hiermit erklärt [Name des Herstellers], dass sich das Gerät [Gerätetyp] in Übereinstimmung mit den grundlegenden Anforderungen und den übrigen einschlägigen Bestimmungen der Richtlinie 1999/5/EG befindet.

Eesti

[Estonian]

English Hereby, [name of manufacturer], declares that this [type of equipment] is in compliance with

Käesolevaga kinnitab [tootja nimi = name of manufacturer] seadme [seadme tüüp = type of equipment] vastavust direktiivi 1999/5/EÜ põhinõuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele sätetele.

the essential requirements and other relevant provisions of Directive 1999/5/EC.

Page 92

F5100 / F5105 / F5110 / F5115 User Manual

Español

[Spanish]

ǼȜȜȘȞȚțȒ

[Greek]

Français

[French]

Italiano

[Italian]

Latviski

[Latvian]

Lietuviǐ

[Lithuanian]

Nederlands

[Dutch]

Por medio de la presente [nombre del fabricante] declara que el [clase de equipo] cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE.

ȂǼ ȉǾȃ ȆǹȇȅȊȈǹ [name of manufacturer] ǻǾȁȍȃǼǿ ȅȉǿ [type of equipment] ȈȊȂȂȅȇĭȍȃǼȉǹǿ ȆȇȅȈ ȉǿȈ ȅȊȈǿȍǻǼǿȈ ǹȆǹǿȉǾȈǼǿȈ Ȁǹǿ ȉǿȈ ȁȅǿȆǼȈ ȈȋǼȉǿȀǼȈ ǻǿǹȉǹȄǼǿȈ ȉǾȈ ȅǻǾīǿǹȈ 1999/5/ǼȀ.

Par la présente [nom du fabricant] déclare que l'appareil [type d'appareil] est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE.

Con la presente [nome del costruttore] dichiara che questo [tipo di apparecchio] è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE.

Ar šo [name of manufacturer / izgatavotƗja nosaukums] deklarƝ, ka [type of equipment / iekƗrtas tips] atbilst DirektƯvas 1999/5/EK bǌtiskajƗm prasƯbƗm un citiem ar to saistƯtajiem noteikumiem.

Šiuo [manufacturer name] deklaruoja, kad šis [equipment type] atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas.

Hierbij verklaart [naam van de fabrikant] dat het toestel [type van toestel] in overeenstemming is met de essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EG.

Malti

[Maltese]

Magyar

[Hungarian]

Polski

[Polish]

Português

[Portuguese]

Slovensko

[Slovenian]

Slovensky

[Slovak]

Suomi

[Finnish]

Svenska

[Swedish]

Hawnhekk, [isem tal-manifattur], jiddikjara li dan [il-mudel tal-prodott] jikkonforma mal-ƫtiƥijiet essenzjali u ma provvedimenti oƫrajn relevanti li hemm fid-Dirrettiva 1999/5/EC.

Alulírott, [gyártó neve] nyilatkozom, hogy a [... típus] megfelel a vonatkozó alapvetõ követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak.

Niniejszym [nazwa producenta] oĞwiadcza, Īe [nazwa wyrobu] jest zgodny z zasadniczymi wymogami oraz pozostaáymi stosownymi postanowieniami Dyrektywy 1999/5/EC.

[Nome do fabricante] declara que este [tipo de equipamento] está conforme com os requisitos essenciais e outras disposições da Directiva 1999/5/CE.

[Ime proizvajalca] izjavlja, da je ta [tip opreme] v skladu z bistvenimi zahtevami in ostalimi relevantnimi doloþili direktive 1999/5/ES.

[Meno výrobcu] týmto vyhlasuje, že [typ zariadenia] spĎĖa základné požiadavky a všetky príslušné ustanovenia Smernice 1999/5/ES.

[Valmistaja = manufacturer] vakuuttaa täten että [type of equipment = laitteen tyyppimerkintä] tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen.

Härmed intygar [företag] att denna [utrustningstyp] står I överensstämmelse med de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv 1999/5/EG.

Page 93

F5100 / F5105 / F5110 / F5115 User Manual

Federal Communication Commission

Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

x Reorient or relocate the receiving antenna. x Increase the separation between the equipment and receiver. x Connect the equipment into an outlet on a circuit different from thatʳto which the receiver is

connected.

x Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC Caution:

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.

IEEE 802.11b or 802.11g operation of this product in the U.S.A. is firmware-limited to channels 1 through 11.

IMPORTANT NOTE: FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

ZAVIO 5115F User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual