Zanussi ZWF 81463WH, ZWF 81463WR Operating Instructions
EN
DE
User Manual 2
Benutzerinformation 19
Washing Machine
Waschmaschine
ZWF 81463WR
ZWF 81463WH
Contents
Safety information 2
Safety instructions 3
Product description 4
Control panel 5
Programme Chart 6
Consumption values
Options
Settings 9
Before first use 10
Daily use 10
Hints and tips 13
Care and cleaning 14
Troubleshooting
7
8
Technical Data
Subject to change without notice.
15
17
Safety information
Before the installation and use of the appliance, carefully read the
supplied instructions. The manufacturer is not responsible if an
incorrect installation and use causes injuries and damages.
Always keep the instructions with the appliance for future
reference.
Children and vulnerable people safety
• This appliance can be used by children aged from 8 years and
above and persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge if they have
been given supervision or instruction concerning use of the
appliance in a safe way and understand the hazards involved.
• Do not let children play with the appliance.
• Keep all packaging away from children.
• Keep all detergents away from children.
• Keep children and pets away from the appliance door when it is
open.
• Cleaning and user maintenance shall not be made by children
without supervision.
General Safety
• Do not change the specification of this appliance.
• Obey the maximum load volume of 8 kg (refer to the
“Programme chart” chapter).
• The operating water pressure (minimum and maximum) must be
between 0,5 bar (0,05 MPa) and 8 bar (0,8 MPa).
2 www.zanussi.com
• The ventilation openings in the base (if applicable) must not be
obstructed by a carpet.
• The appliance is to be connected to the water mains using the
new supplied hose-sets. Old hose sets must not be reused.
• If the supply cord is damaged, it must be replaced by the
manufacturer, its Authorised Service Centre or similarly
qualified persons in order to avoid a hazard.
• Before maintenance, deactivate the appliance and disconnect
the mains plug from the mains socket.
• Do not use water spray and steam to clean the appliance.
• Clean the appliance with a moist soft cloth. Only use neutral
detergents. Do not use abrasive products, abrasive cleaning
pads, solvents or metal objects.
Safety instructions
Installation
• Remove all the packaging and the transit
bolts.
• Keep the transit bolts. When you move the
appliance again you must block the drum.
• Always be careful when you move the
appliance because it is heavy. Always wear
safety gloves.
• Do not install or use a damaged appliance.
• Obey the installation instruction supplied
with the appliance.
• Do not install or use the appliance where the
temperature is less than 0 °C or where it is
exposed to the weather.
• Make sure that the floor where you install the
appliance is flat, stable, heat resistant and
clean.
• Do not install the appliance where the
appliance door can not be fully opened.
• Make sure that there is air circulation
between the appliance and the floor.
• Adjust the feet to have the necessary space
between the appliance and the carpet.
• Do not install the appliance where the
appliance door can not be fully opened.
Electrical Connection
• The appliance must be earthed.
• Always use a correctly installed shockproof
socket.
• Make sure that the electrical information on
the rating plate agrees with the power
supply. If not contact an electrician.
• Do not use multi-plug adapters and
extension cables.
• Make sure not to cause damage to the
mains plug and to the mains cable. Should
the mains cable need to be replaced, this
must be carried out by our Authorised
Service Centre.
• Connect the mains plug to the mains socket
only at the end of the installation. Make sure
that there is access to the mains plug after
the installation.
• Do not touch the mains cable or the mains
plug with wet hands.
• Do not pull the mains cable to disconnect
the appliance. Always pull the mains plug.
• Only for UK and Ireland: The appliance has a
13 amp mains plug. If it is necessary to
change the fuse in the mains plug, use a 13
amp ASTA (BS 1362) fuse.
• This appliance complies with the E.E.C.
Directives.
Water connection
• Make sure not to cause damage to the water
hoses.
• Before you connect the appliance to new
pipes or pipes not used for a long time, let
the water flow until it is clean.
www.zanussi.com 3
• The first time you use the appliance, make
1 2 3
5
6
4
sure that there is no leakage.
Use
WARNING!
Risk of injury, electrical shock, fire,
burns or damage to the appliance.
• Use this appliance in a household only.
• Obey the safety instructions on the
detergent packaging.
• Do not put flammable products or items that
are wet with flammable products in, near or
on the appliance.
• Make sure that you remove all metal objects
from the laundry.
Product description
Appliance overview
• Do not put a container to collect possible
water leakage under the appliance. Contact
the Authorised Service Centre to ensure
which accessories can be used.
• Do not touch the glass of the door while a
programme operates. The glass can be hot.
Disposal
WARNING!
Risk of injury or suffocation.
• Disconnect the appliance from the mains
supply.
• Cut off the mains cable and discard it.
• Remove the door catch to prevent children
and pets to get closed in the appliance.
Worktop
1
Detergent dispenser
2
Control panel
3
Door handle
4
Rating plate
5
Feet for the appliance level
6
4 www.zanussi.com
Control panel
97621 3 4 5 8
A
DB
C
Control panel description
1
On / Off button (Aan/Uit-Marche/Arrêt)
2
Programme selection touchpad
3
Temperature touchpad
4
Spin selection touchpad
5
Options selection touchpad
Display
6
Start/Pause touchpad
7
Finish in touchpad (Klaar Over/Fini
Dans)
Display
8
9
Door locked indicator
A) The time area:
• : the programme duration
• : the "finish in" time
• : the alarm codes
• : the message of error
• : the programme is completed.
B) The child lock indicator:
• The indicator comes on when you
activate this device.
C) The extra rinse indicator:
• The indicator comes on when you
activate this option.
D) The Klaar Over/Fini Dans touchpad.
www.zanussi.com 5
Programme Chart
Programme
Temperature
range
30' @ 30°
30 °C
Katoen/Coton
90 °C - Cold
Katoen/Coton
1)
ECO
60 °C - 40 °C
Synthetica/Synthétiques
Maximum load
Maximum spin
speed
3 kg
800 rpm
8 kg
1400 rpm
8 kg
1400 rpm
3 kg
1200 rpm
Programme description
(Type of load and soil level)
A short cycle for synthetics and delicate items with
light soil level or for items to freshen up.
White cotton and coloured cotton. Normal soil and light
soil.
White cotton and colour-fast cotton. Normal soil. The
energy consumption decreases and the time of the washing
programme is extended.
Synthetic items or mixed fabric items. Normal soil.
60 °C - Cold
Fijne Was/Délicats
40 °C - Cold
Wol/Laine
40 °C - Cold
Dekbed/Couette
60 °C - Cold
Mix 20°/Mixtes 20°
20 °C
3 kg
1200 rpm
2 kg
1200 rpm
3 kg
800 rpm
2 kg
1200 rpm
Delicate fabrics as acrylics, viscose, polyester items.
Normal soil.
Machine washable wool, hand washable wool and
delicate fabrics with «hand washing» care symbol.
2)
Special programme for one synthetic blanket, duvet,
bedspread and so on.
Special programme for cotton, synthetic and mixed fabrics
with light soil. Set this programme to decrease the energy
consumption. Make sure that the detergent is for low tem-
perature in order to have good washing results3).
1) Standard programmes for the Energy Label consumption values. According to regulation 1061/2010, these programmes are respectively the «Standard 60°C cotton programme» and the «Standard 40°C cotton programme». They are the most efficient programmes in
terms of combined energy and water consumption for washing normally soiled cotton laundry.
The water temperature of the washing phase may differ from the temperature declared for the selected programme.
2) During this cycle the drum rotates slowly to ensure a gentle washing. It can seem that the drum doesn't rotate or doesn't rotate properly.
Consider this as a normal functioning of the appliance.
3) No temperature indicator is on .
6 www.zanussi.com
Programme options compatibility
Pro-
gramme
30' @ 30° ■ ■ ■ ■
Katoen/
Coton
Katoen/
Coton ECO
Synthetica/
Synthétiques
Fijne Was/
Délicats
Wol/Laine ■ ■ ■ ■ ■ ■
Dekbed/
Couette
Mix 20°/
Mixtes 20°
1) When you set this option, we recommend that you decrease the quantity of the laundry. It is possible to keep the full load but the washing
results can be unsatisfactory. Recommended load: cotton: 4 kg, synthetics and delicates: 1,5 kg.
■ ■ ■ ■ ■ ■ ■ ■ ■ ■
■ ■ ■ ■ ■ ■ ■ ■
■ ■ ■ ■ ■ ■ ■ ■ ■ ■
■ ■ ■ ■ ■ ■ ■ ■ ■
■ ■ ■ ■ ■ ■
■ ■ ■ ■ ■ ■ ■
Snel/
Rapide
In-
ten-
1)
sief/
In-
ten-
sif
Anti-
kreuk/
Anti-
frois-
sage
Spoe-
len/
Rin-
çage
Pomp-
en/
Centri-
fugeren
Vi-
dange/
Essor-
age
Consumption values
The data of this table are approximate. Different causes can change the data: the quantity and type of laundry, the water and ambient temperature.
At programme start the display shows the duration programme for the maximum load
capacity. During the washing phase the programme duration is automatically calculated
and can be greatly reduced if the laundry load is lower than the maximum load capacity
(e.g. Cotton 60°C, maximum load capacity 8 kg, the programme duration exceeds 2
hours; real load 1 kg, the programme duration don’t reach 1 hour). When the appliance
is calculating the real programme duration a dot blinks in the display.
www.zanussi.com 7
Programmes Load
(kg)
Katoen/Coton 60 °C 8 1,35 70 159 53
Katoen/Coton 40 °C 8 0,87 69 158 53
Synthetica/Synthé-
tiques 40 °C
Fijne Was/Délicats 40
°C
Wol/Laine 30 °C 2 0,30 53 57 30
Standard cotton programmes
Standard 60 °C cotton 8 0,96 52 244 53
Standard 60 °C cotton 4 0,73 40 210 53
Standard 40 °C cotton 4 0,62 41 196 53
1) At the end of spin phase.
Off Mode (W) Left On Mode (W)
The information given in the chart above are in compliance with the EU Commission regulation
1015/2010 implementing directive 2009/125/EC.
3 0,60 56 103 35
3 0,55 59 81 35
0,48 0,48
Energy
consump-
tion (kWh)
Water con-
sumption
(litre)
Approxi-
mate pro-
gramme
duration
(minutes)
Remaining
moisture
(%)
1)
Options
Temperature
With this option you can change the default
temperature.
Indicator = cold water.
The indicator of the set temperature comes on.
Spin
With this option you can change the default
spin speed.
The indicator of the set speed comes on.
Additional spin options:
No Spin
• Set this option to deactivate all spin phases.
Only the drain phase is available.
• The related indicator comes on.
8 www.zanussi.com
• Set this option for very delicate fabrics.
• The rinses phase uses more water for some
washing programmes.
Rinse Hold
• Set this option to prevent the laundry
creases.
• The related indicator comes on.
• There is a water in the drum when the
programme is completed.
• The drum turns regularly to prevent the
laundry creases.
• The door stays locked. You must drain the
water to unlock the door.
To drain the water refer to ‘At the
end of the programme’.
Snel/Rapide
With this option you can decrease the
programme duration.
Use this option for items with light soil or items
to refresh.
The related indicator comes on.
Intensief/Intensif
With this option you can wash very soiled
laundry.
The washing cycle lasts longer with this option.
The related indicator comes on.
Anti-kreuk/Anti-froissage
The appliance carefully washes and spins the
laundry to prevent the creases.
The appliance decreases the spin speed, uses
more water and adapts the programme duration
to the type of laundry.
The related indicator comes on.
Spoelen/Rinçage
With this option you can perform only a last
rinse of a selected washing programme.
If you set also the Extra Rinse function ( ) the
appliance adds two or more rinses.
The related indicator comes on.
Pompen/Centrifugeren Vidange/ Essorage
With this option you can the spin and drain
cycle.
The spin phase is suitable to the washing
programme you set.
If you set also the No Spin ( )
option, the appliance only drains.
Klaar Over/Fini Dans
With this option you can set the number of
hours in which you would like your washing
programme to be completed.
You can set from minimum 3 hours to maximum
20 hours.
The display shows the number of hours and the
indicator above the button is on.
Extra Rinse
With this option you can add some rinses to a
washing programme.
Use this option for persons allergic to
detergents and in areas where the water is soft.
The related indicator comes on.
1
Settings
Extra Rinse
With this option you can permanently have an
extra rinse when you set a new programme.
• To activate/deactivate this option touch
the buttons and at the same time until
the indicator comes on/goes off.
Child Lock
With this option you can prevent that the
children play with the control panel.
• To activate/deactivate this option, touch
the buttons
the indicator comes on/goes off.
1 See in "Settings" how to activate this option.
and at the same time until
www.zanussi.com 9
Activate this option after you touch the button
: the buttons are locked (except for the
button ) .
This option stays active even when
you switch off the appliance.
Acoustic signals
The acoustic signals operate when:
• The programme is completed.
• The appliance has a malfunction.
To deactivate/activate the acoustic signals,
touch the buttons
for 4 seconds.
and at the same time
If you deactivate the acoustic
A
signals, they continue operate when
the appliance has a malfunction.
Before first use
1. Put a small quantity of detergent in the
compartment for washing phase.
2. Set and start a programme for cotton at the
highest temperature without laundry.
Daily use
WARNING!
Refer to Safety chapters.
Loading the laundry
Open the water tap. Connect the mains plug to
the mains socket.
1. Pull the door handle to open the appliance
door.
2. Put the laundry in the drum, one item at a
time.
3. Shake the items before you put them in the
appliance.
Make sure not to put too much laundry in the
drum. Refer to max. loads indicated in
"Programme chart".
4. Close the door.
CAUTION!
Make sure
that no
laundry
stays
between the
seal and the
door. There
is a risk of
water
leakage or
damage to
the laundry.
This removes all possible dirt from the drum and
the tub.
Using detergent and additives
1. Measure out the
detergent and the
fabric conditioner.
2. Carefully close the
detergent drawer.
Detergent compartments
Detergent compartment for washing phase.
If you use liquid detergent, put it
immediately before you start the
programme.
Compartment for liquid additives
(fabric conditioner, starch).
CAUTION!
Do not exceed the
MAX level.
Flap for powder or liquid detergent.
Liquid or powder detergent
The default position of
the flap is A (powder
detergent).
10 www.zanussi.com
To use liquid detergent:
B
A
1. Remove the drawer.
Push the drawer edge in
the place with the arrow
(PUSH) to remove the
drawer easily.
2. Adjust the flap in
position B.
3. Put back the drawer in
the recess.
When you use the liquid detergent:
• Do not use gelatinous or thick
liquid detergents.
• Do not put more liquid then 120
ml.
• Do not set the delay start.
When the flap is in
position B and you want
to use powder detergent:
1. Remove the drawer.
2. Adjust the flap in
position A.
3. Put back the drawer
in the recess.
Setting a programme
1. Touch the programme button and set the
programme:
• The indicator of the button flashes.
• The display shows the programme
duration.
2. If necessary, change the temperature and
the spin speed or add available options.
When you activate an option, the indicator
of the set option comes on.
If you set something incorrect, the
display shows the message .
Starting a programme without the Klaar Over/Fini Dans option
Touch the button .
• The indicator of the button stops to
flash and stays on.
• The programme starts, the door locks,
the indicator is on.
• The drain pump can operate for a short
time at the beginning of the washing
cycle.
After approximately 15 minutes from
the start of the programme:
• The appliance adjusts
automatically the programme
duration agree with the laundry
load.
• The display shows the new value.
• Measure out the detergent and the fabric
conditioner.
• Put the detergent and the fabric conditioner
into the compartments.
• Carefully close the detergent drawer.
Activating the appliance
Press and hold for a couple of seconds the
button to activate or deactivate the appliance.
A tune sounds when the appliance is activated.
The appliance performs a start up animation.
The animation quickly shows each washing
programme and the default temperature and
spin settings.
The display shows the word On.
Starting a programme with the Klaar Over/Fini Dans option
1. Touch the button again and again to
choose the number of hours in which you
want the washing cycle to be finished.
The display shows the number of hours you set
(e.g. ) and the indicator above the button
is on to show that his option is active.
2. Touch the button :
• The door is locked.
• The appliance starts the countdown.
• When the countdown is completed, the
programme starts automatically.
www.zanussi.com 11
You can cancel or change the set of
the Klaar Over/Fini Dans option
before you touch the button .
After touching the button you
can only cancel the Klaar Over/Fini
Dans option.
To cancel the the Klaar Over/Fini Dans option:
a. Touch the button to set the
appliance to pause. The indicator of
button flashes.
b. Touch the button until the indicator
above this button goes off.
Touch the button again to start the
programme immediately.
Interrupting a programme and changing the options
You can change only some options before they
operate.
1. Touch .
The indicator of this button flashes.
2. Change the options. If you change any
option the Klaar Over/Fini Dans option (if
set) will be disabled.
3. Touch again.
The programme continues.
Cancelling a programme
1. Press the button for some seconds to
cancel the programme and to deactivate the
appliance.
2. Press the same button again to activate the
appliance. Now, you can set a new washing
programme.
The appliance does not drain the
water. The water left in a drum can
be used for the next washing cycle.
Opening the door
While a programme (or the ) operates, the
appliance door is locked. The indicator is
on.
CAUTION!
If the temperature and level of the
water in the drum are too high, you
cannot open the door.
To open the door during the first minutes
of the cycle (or when the operates) :
1. Touch the button to pause the
appliance.
2. Wait until the indicator goes off.
3. You can open the door.
4. Close the door and touch the button
again. The programme (or the )
continues.
At the end of the programme
• The appliance stops automatically.
• The acoustic signal operates (if it is
activated).
• In the display comes on.
• The indicator of the button goes off.
• The door lock indicator goes off.
• You can open the door.
• Remove the laundry from the appliance.
Make sure that the drum is empty.
• Press the button for some seconds to
deactivate the appliance.
• Close the water tap.
• Keep the door and the detergent drawer
ajar, to prevent the mildew and odours.
The washing programme is completed,
but there is water in the drum:
• The drum turns regularly to prevent the
creases in the laundry.
• The indicator
drain the water.
• The door lock indicator is on. The
indicator of button flashes. The door
stays locked.
• You must drain the water to open the door.
Draining the water:
1. To drain the water.
• Touch the button . The appliance
drains the water and spins with the
maximum spin speed for selected
washing programme.
• Alternatively, touch the button to
change the spin speed and then touch
the button . The appliance drains the
flashes to remind you to
12 www.zanussi.com
Loading...