Page 1
EN
User Manual
Washing Machine
ZWF 71263W
ZWF 71463W
Page 2
Contents
Safety information 2
Safety instructions 3
Product description 4
Control panel 5
Programme Chart 6
Consumption values
Options
Settings 9
Before first use 10
Daily use 10
Hints and tips 13
Care and cleaning 14
Troubleshooting
7
8
Technical Data
Subject to change without notice.
15
17
Safety information
Before the installation and use of the appliance, carefully read the
supplied instructions. The manufacturer is not responsible if an
incorrect installation and use causes injuries and damages.
Always keep the instructions with the appliance for future
reference.
Children and vulnerable people safety
• This appliance can be used by children aged from 8 years and
above and persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge if they have
been given supervision or instruction concerning use of the
appliance in a safe way and understand the hazards involved.
• Do not let children play with the appliance.
• Keep all packaging away from children.
• Keep all detergents away from children.
• Keep children and pets away from the appliance door when it is
open.
• Cleaning and user maintenance shall not be made by children
without supervision.
General Safety
• Do not change the specification of this appliance.
• Obey the maximum load volume of 7 kg (refer to the
“Programme chart” chapter).
• The operating water pressure (minimum and maximum) must be
between 0,5 bar (0,05 MPa) and 8 bar (0,8 MPa).
2 www.zanussi.com
Page 3
• The ventilation openings in the base (if applicable) must not be
obstructed by a carpet.
• The appliance is to be connected to the water mains using the
new supplied hose-sets. Old hose sets must not be reused.
• If the supply cord is damaged, it must be replaced by the
manufacturer, its Authorised Service Centre or similarly
qualified persons in order to avoid a hazard.
• Before maintenance, deactivate the appliance and disconnect
the mains plug from the mains socket.
• Do not use water spray and steam to clean the appliance.
• Clean the appliance with a moist soft cloth. Only use neutral
detergents. Do not use abrasive products, abrasive cleaning
pads, solvents or metal objects.
Safety instructions
Installation
• Remove all the packaging and the transit
bolts.
• Keep the transit bolts. When you move the
appliance again you must block the drum.
• Always be careful when you move the
appliance because it is heavy. Always wear
safety gloves.
• Do not install or use a damaged appliance.
• Obey the installation instruction supplied
with the appliance.
• Do not install or use the appliance where the
temperature is less than 0 °C or where it is
exposed to the weather.
• Make sure that the floor where you install the
appliance is flat, stable, heat resistant and
clean.
• Do not install the appliance where the
appliance door can not be fully opened.
• Make sure that there is air circulation
between the appliance and the floor.
• Adjust the feet to have the necessary space
between the appliance and the carpet.
Electrical Connection
• The appliance must be earthed.
• Always use a correctly installed shockproof
socket.
• Make sure that the electrical information on
the rating plate agrees with the power
supply. If not contact an electrician.
• Do not use multi-plug adapters and
extension cables.
• Make sure not to cause damage to the
mains plug and to the mains cable. Should
the mains cable need to be replaced, this
must be carried out by our Authorised
Service Centre.
• Connect the mains plug to the mains socket
only at the end of the installation. Make sure
that there is access to the mains plug after
the installation.
• Do not touch the mains cable or the mains
plug with wet hands.
• Do not pull the mains cable to disconnect
the appliance. Always pull the mains plug.
• Only for UK and Ireland: The appliance has a
13 amp mains plug. If it is necessary to
change the fuse in the mains plug, use a 13
amp ASTA (BS 1362) fuse.
• This appliance complies with the E.E.C.
Directives.
Water connection
• Make sure not to cause damage to the water
hoses.
• Before you connect the appliance to new
pipes or pipes not used for a long time, let
the water flow until it is clean.
• The first time you use the appliance, make
sure that there is no leakage.
www.zanussi.com 3
Page 4
Use
1 2 3
5
6
4
WARNING!
Risk of injury, electrical shock, fire,
burns or damage to the appliance.
• Use this appliance in a household only.
• Obey the safety instructions on the
detergent packaging.
• Do not put flammable products or items that
are wet with flammable products in, near or
on the appliance.
• Make sure that you remove all metal objects
from the laundry.
• Do not put a container to collect possible
water leakage under the appliance. Contact
Product description
Appliance overview
the Authorised Service Centre to ensure
which accessories can be used.
• Do not touch the glass of the door while a
programme operates. The glass can be hot.
Disposal
WARNING!
Risk of injury or suffocation.
• Disconnect the appliance from the mains
supply.
• Cut off the mains cable and discard it.
• Remove the door catch to prevent children
and pets to get closed in the appliance.
Worktop
1
Detergent dispenser
2
Control panel
3
Door handle
4
Rating plate
5
Feet for the appliance level
6
Installation on suspended flooring
Suspended wooden floors are particularly
susceptible to vibration.
To help prevent vibration we recommend you
place a waterproof wood panel, at least 15 mm
thick under the appliance, secured to at least 2
floor beams with screws, the wood panel must
extend beyond the front feet.
If possible install the appliance in one of the
corners of the room, where the floor is more
stable.
4 www.zanussi.com
Page 5
Control panel
1400
90°
60°
40°
30°
1200
800
Intensive
Easy Iron
Rinse Only
Drain & Spin
Cottons
Synthetics
Delicates
Wool/Handwash
Mix 20°
Cotton ECO
Refresh 20 min
Quick
P
On/ Off
Finish In
987621 3 4 5
Finish In
A
D
B C
Control panel description
1
On / Off button (On/Off)
2
Programme selection touchpad
3
Temperature touchpad
4
Spin selection touchpad
5
Options selection touchpad
Display
6
Start/Pause touchpad
7
Finish in touchpad (Finish In)
Display
8
9
Door locked indicator
A) The time area:
• : the programme duration
• : the "finish in" time
• : the alarm codes
• : the message of error
• : the programme is completed.
B) The child lock indicator:
• The indicator comes on when you
activate this device.
C) The extra rinse indicator:
• The indicator comes on when you
activate this option.
D) The Finish In button.
www.zanussi.com 5
Page 6
Programme Chart
Programme
Temperature range
Maximum load
Maximum spin speed
Programme description
(Type of load and soil level)
30' @ 30°
30 °C
A short cycle for synthetics and delicate items with light soil level or for
items to freshen up.
3 kg
800 rpm for model ZWF 71263W; 800 rpm for model ZWF 71463W
Cottons
90 °C - Cold
White cotton and coloured cotton. Normal soil and light soil.
7 kg
1200 rpm for model ZWF 71263W; 1400 for model ZWF 71463W
White cotton and colour-fast cotton. Normal soil. The energy consumption
Cotton Eco
60 °C - 40 °C
1)
decreases and the time of the washing programme is extended.
7 kg
1200 rpm for model ZWF 71263W; 1400 for model ZWF 71463W
Synthetics
60 °C - Cold
Synthetic items or mixed fabric items. Normal soil.
3 kg
1200 rpm for model ZWF 71263W; 1200 rpm for model ZWF 71463W
Delicates
40 °C - Cold
Delicate fabrics as acrylics, viscose, polyester items. Normal soil.
3 kg
1200 rpm for model ZWF 71263W; 1200 rpm for model ZWF 71463W
Wool/Handwash
40 °C - Cold
Machine washable wool, hand washable wool and delicate fabrics
with «hand washing» care symbol.
2)
2 kg
1200 rpm for model ZWF 71263W; 1200 rpm for model ZWF 71463W
Refresh 20 min
40 °C - 30 °C
A very short cycle for cottons and synthetics items with light soil level or
worn only once.
1 kg
1200 rpm for model ZWF 71263W; 1200 rpm for model ZWF 71463W
Mix 20°
20 °C
Special programme for cotton, synthetic and mixed fabrics with light soil. Set
this programme to decrease the energy consumption. Make sure that the de-
tergent is for low temperature in order to have good washing results3).
2 kg
1200 rpm for model ZWF 71263W; 1200 for model ZWF 71463W
1) Standard programmes for the Energy Label consumption values. According to regulation 1061/2010, these programmes are respectively the «Standard 60°C cotton programme» and the «Standard 40°C cotton programme». They are the most efficient programmes in
terms of combined energy and water consumption for washing normally soiled cotton laundry.
The water temperature of the washing phase may differ from the temperature declared for the selected programme.
2) During this cycle the drum rotates slowly to ensure a gentle washing. It can seem that the drum doesn't rotate or doesn't rotate properly.
Consider this as a normal functioning of the appliance.
3) No temperature indicator is on .
6 www.zanussi.com
Page 7
Programme options compatibility
Pro-
gramme
Quick
In-
1)
ten-
Easy
Iron
Rinse
Only
Drain &
Spin
sive
30' @ 30° ■ ■ ■ ■
Cottons ■ ■ ■ ■ ■ ■ ■ ■ ■ ■
Cotton Eco ■ ■ ■ ■ ■ ■ ■ ■
Synthetics ■ ■ ■ ■ ■ ■ ■ ■ ■ ■
Delicates ■ ■ ■ ■ ■ ■ ■ ■ ■
Wool/Hand-
wash
Refresh 20
min
■ ■ ■ ■ ■ ■
■ ■ ■ ■ ■ ■
Mix 20° ■ ■ ■ ■ ■ ■ ■
1) When you set this option, we recommend that you decrease the quantity of the laundry. It is possible to keep the full load but the washing
results can be unsatisfactory. Recommended load: cotton: 3,5 kg, synthetics and delicates: 1,5 kg.
Consumption values
The data of this table are approximate. Different causes can change the data: the quantity and type of laundry, the water and ambient temperature.
At programme start the display shows the duration programme for the maximum load
capacity. During the washing phase the programme duration is automatically calculated
and can be greatly reduced if the laundry load is lower than the maximum load capacity
(e.g. Cotton 60°C, maximum load capacity 7 kg, the programme duration exceeds 2
hours; real load 1 kg, the programme duration don’t reach 1 hour). When the appliance
is calculating the real programme duration a dot blinks in the display.
Pro-
grammes
Load (kg) Energy con-
sumption
(kWh)
Water con-
sumption
(litre)
Approxi-
mate pro-
gramme du-
ration (mi-
Remaining
moisture
1)
(%)
nutes)
Cottons 60 °C
Cottons 40 °C
Synthetics 40
°C
Delicates 30 °C
7 1,34 68 157
7 0,78 61 157
3 0,60 56 103
3 0,55 59 81
532) / 52
532) / 52
352) / 35
352) / 35
3)
3)
3)
3)
www.zanussi.com 7
Page 8
Pro-
grammes
Load (kg) Energy con-
sumption
(kWh)
Water con-
sumption
(litre)
Approxi-
mate pro-
gramme du-
ration (mi-
nutes)
Remaining
moisture
1)
(%)
Wool/Handwash 30 °C
Standard cotton programmes
Standard 60 °C
cotton
Standard 60 °C
cotton
Standard 40 °C
cotton
1) At the end of spin phase.
2) For model ZWF 71263W.
3) For model ZWF 71463W.
The information given in the chart above are in compliance with the EU Commission regulation
1015/2010 implementing directive 2009/125/EC.
2 0,30 53 57
7 0,92 44 250
3,5 0,68 35 204
3,5 0,53 36 189
Off Mode (W) Left On Mode (W)
0,48 0,48
Options
Temperature
With this option you can change the default
temperature.
Indicator = cold water.
The indicator of the set temperature comes on.
Spin
With this option you can change the default
spin speed.
The indicator of the set speed comes on.
Additional spin options:
No Spin
• Set this option to deactivate all spin phases.
Only the drain phase is available.
• The related indicator comes on.
• Set this option for very delicate fabrics.
• The rinses phase uses more water for some
washing programmes.
Rinse Hold
• Set this option to prevent the laundry
creases.
• The related indicator comes on.
• There is a water in the drum when the
programme is completed.
• The drum turns regularly to prevent the
laundry creases.
• The door stays locked. You must drain the
water to unlock the door.
To drain the water refer to ‘At the
end of the programme’.
Quick
With this option you can decrease the
programme duration.
Use this option for items with light soil or items
to refresh.
302) / 30
532) / 52
532) / 52
532) / 52
3)
3)
3)
3)
8 www.zanussi.com
Page 9
The related indicator comes on.
Intensive
With this option you can wash very soiled
laundry.
The washing cycle lasts longer with this option.
The related indicator comes on.
Easy Iron
The appliance carefully washes and spins the
laundry to prevent the creases.
The appliance decreases the spin speed, uses
more water and adapts the programme duration
to the type of laundry.
The related indicator comes on.
Rinse Only
With this option you can perform only a last
rinse of a selected washing programme.
If you set also the Extra Rinse function ( ) the
appliance adds two or more rinses.
The related indicator comes on.
Drain & Spin
With this option you can the spin and drain
cycle.
The spin phase is suitable to the washing
programme you set.
If you set also the No Spin ( )
option, the appliance only drains.
Finish In
With this option you can set the number of
hours in which you would like your washing
programme to be completed.
You can set from minimum 3 hours to maximum
20 hours.
The display shows the number of hours and the
indicator above the button is on.
Extra Rinse
With this option you can add some rinses to a
washing programme.
Use this option for persons allergic to
detergents and in areas where the water is soft.
The related indicator comes on.
1
Settings
Extra Rinse
With this option you can permanently have an
extra rinse when you set a new programme.
• To activate/deactivate this option touch
the buttons and at the same time until
the indicator comes on/goes off.
Child Lock
With this option you can prevent that the
children play with the control panel.
• To activate/deactivate this option, touch
the buttons
the indicator comes on/goes off.
1 See in "Settings" how to activate this option.
and at the same time until
www.zanussi.com 9
Activate this option after you touch the button
: the buttons are locked (except for the
button ) .
This option stays active even when
you switch off the appliance.
Acoustic signals
The acoustic signals operate when:
• The programme is completed.
• The appliance has a malfunction.
To deactivate/activate the acoustic signals,
touch the buttons
for 4 seconds.
and at the same time
Page 10
If you deactivate the acoustic
A
signals, they continue operate when
the appliance has a malfunction.
Before first use
1. Put a small quantity of detergent in the
compartment for washing phase.
2. Set and start a programme for cotton at the
highest temperature without laundry.
Daily use
WARNING!
Refer to Safety chapters.
Loading the laundry
Open the water tap. Connect the mains plug to
the mains socket.
1. Pull the door handle to open the appliance
door.
2. Put the laundry in the drum, one item at a
time.
3. Shake the items before you put them in the
appliance.
Make sure not to put too much laundry in the
drum. Refer to max. loads indicated in
"Programme chart".
4. Close the door.
CAUTION!
Make sure
that no
laundry
stays
between the
seal and the
door. There
is a risk of
water
leakage or
damage to
the laundry.
This removes all possible dirt from the drum and
the tub.
Using detergent and additives
1. Measure out the
detergent and the
fabric conditioner.
2. Carefully close the
detergent drawer.
Detergent compartments
Detergent compartment for washing phase.
If you use liquid detergent, put it
immediately before you start the
programme.
Compartment for liquid additives
(fabric conditioner, starch).
CAUTION!
Do not exceed the
MAX level.
Flap for powder or liquid detergent.
Liquid or powder detergent
The default position of
the flap is A (powder
detergent).
10 www.zanussi.com
Page 11
To use liquid detergent:
B
A
1. Remove the drawer.
Push the drawer edge in
the place with the arrow
(PUSH) to remove the
drawer easily.
2. Adjust the flap in
position B.
3. Put back the drawer in
the recess.
When you use the liquid detergent:
• Do not use gelatinous or thick
liquid detergents.
• Do not put more liquid then 120
ml.
• Do not set the delay start.
When the flap is in
position B and you want
to use powder detergent:
1. Remove the drawer.
2. Adjust the flap in
position A.
3. Put back the drawer
in the recess.
Setting a programme
1. Touch the programme button and set the
programme:
• The indicator of the button flashes.
• The display shows the programme
duration.
2. If necessary, change the temperature and
the spin speed or add available options.
When you activate an option, the indicator
of the set option comes on.
If you set something incorrect, the
display shows the message .
Starting a programme without the Finish In option
Touch the button .
• The indicator of the button stops to
flash and stays on.
• The programme starts, the door locks,
the indicator is on.
• The drain pump can operate for a short
time at the beginning of the washing
cycle.
After approximately 15 minutes from
the start of the programme:
• The appliance adjusts
automatically the programme
duration agree with the laundry
load.
• The display shows the new value.
• Measure out the detergent and the fabric
conditioner.
• Put the detergent and the fabric conditioner
into the compartments.
• Carefully close the detergent drawer.
Activating the appliance
Press and hold for a couple of seconds the
button to activate or deactivate the appliance.
A tune sounds when the appliance is activated.
The appliance performs a start up animation.
The animation quickly shows each washing
programme and the default temperature and
spin settings.
The display shows the word On.
Starting a programme with the Finish In option
1. Touch the button again and again to
choose the number of hours in which you
want the washing cycle to be finished.
The display shows the number of hours you set
(e.g. ) and the indicator above the button
is on to show that his option is active.
2. Touch the button :
• The door is locked.
• The appliance starts the countdown.
• When the countdown is completed, the
programme starts automatically.
www.zanussi.com 11
Page 12
You can cancel or change the set of
the Finish In option before you touch
the button . After touching the
button you can only cancel the
Finish In option.
To cancel the the Finish In option:
a. Touch the button to set the
appliance to pause. The indicator of
button flashes.
b. Touch the button until the indicator
above this button goes off.
Touch the button again to start the
programme immediately.
Interrupting a programme and changing the options
You can change only some options before they
operate.
1. Touch .
The indicator of this button flashes.
2. Change the options. If you change any
option the Finish In option (if set) will be
disabled.
3. Touch again.
The programme continues.
Cancelling a programme
1. Press the button for some seconds to
cancel the programme and to deactivate the
appliance.
2. Press the same button again to activate the
appliance. Now, you can set a new washing
programme.
The appliance does not drain the
water. The water left in a drum can
be used for the next washing cycle.
Opening the door
While a programme (or the ) operates, the
appliance door is locked. The indicator is
on.
CAUTION!
If the temperature and level of the
water in the drum are too high, you
cannot open the door.
To open the door during the first minutes
of the cycle (or when the operates) :
1. Touch the button to pause the
appliance.
2. Wait until the indicator goes off.
3. You can open the door.
4. Close the door and touch the button
again. The programme (or the )
continues.
At the end of the programme
• The appliance stops automatically.
• The acoustic signal operates (if it is
activated).
• In the display comes on.
• The indicator of the button goes off.
• The door lock indicator goes off.
• You can open the door.
• Remove the laundry from the appliance.
Make sure that the drum is empty.
• Press the button for some seconds to
deactivate the appliance.
• Close the water tap.
• Keep the door and the detergent drawer
ajar, to prevent the mildew and odours.
The washing programme is completed,
but there is water in the drum:
• The drum turns regularly to prevent the
creases in the laundry.
• The indicator
drain the water.
• The door lock indicator is on. The
indicator of button flashes. The door
stays locked.
• You must drain the water to open the door.
Draining the water:
1. To drain the water.
• Touch the button . The appliance
drains the water and spins with the
maximum spin speed for selected
washing programme.
• Alternatively, touch the button to
change the spin speed and then touch
the button . The appliance drains the
water and spins. If you set , the
appliance only drains.
flashes to remind you to
12 www.zanussi.com
Page 13
2. When the programme is completed and the
door lock indicator goes off, you can
open the door.
3. Press the button for some seconds to
deactivate the appliance.
The appliance drains and spins
automatically after approximately 18
hours (except for Wool programme).
AUTO-OFF option
The AUTO-OFF stand-by option automatically
deactivates the appliance to decrease the
energy consumption. All the indicators and the
display go off when :
Hints and tips
• You do not use the appliance for 5 minutes
before you touch .
Press the button to activate the appliance
again.
• After 5 minutes from the end of the washing
programme.
Press the button to activate the appliance
again.
The display shows the end of the last set
programme.
Touch the button if you want to set a new
cycle.
The laundry load
• Divide the laundry in: white, coloured,
synthetics, delicates and wool.
• Obey the washing instructions that are on
the laundry care labels.
• Do not wash together white and coloured
items.
• Some coloured items can discolour with the
first wash. We recommend that you wash
them separately for the first times.
• Button up pillowcases, close zippers, hooks
and poppers. Tie up belts.
• Empty the pockets and unfold the items.
• Turn inside out multilayered fabrics, wool
and items with painted illustrations.
• Remove hard stains.
• Wash with a special detergent heavy soil
stains.
• Be careful with the curtains. Remove the
hooks or put the curtains in a washing bag
or pillowcase.
• Do not wash in the appliance laundry without
hems or with cuts. Use a washing bag to
wash small and/or delicate items (e.g.
underwired bras, belts, tights, etc. ).
• A very small load can cause balance
problems with the spin phase. If this occurs,
adjust manually the items in the tub and start
the spin phase again.
Stubborn stains
For some stains, water and detergent is not
sufficient.
We recommend that you remove these stains
before you put the items in the appliance.
Special stain removers are available. Use the
special stain remover that is applicable to the
type of stain and fabric.
Detergents and additives
• Only use detergents and additives specially
made for washing machines:
– powder detergents for all types of fabric,
– powder detergents for delicate fabrics
(40 °C max) and woollens,
– liquid detergents, preferably for low
temperature wash programmes (60 °C
max) for all types of fabric, or special for
woollens only.
• Do not mix different types of detergents.
• To help the environment, do not use more
than the correct quantity of detergent.
• Obey the instructions that you find on the on
packaging of these products.
• Use the correct products for the type and
colour of the fabric, the programme
temperature and the level of soil.
• If your appliance has not the detergent
dispenser with the flap device, add the liquid
detergents with a dosing ball (supplied by
the detergent's manufacturer).
Ecological hints
• Set a programme without the prewash
phase to wash laundry with normal soil.
• Always start a washing programme with the
maximum load of laundry.
• If necessary, use a stain remover when you
set a programme with a low temperature.
www.zanussi.com 13
Page 14
• To use the correct quantity of the detergent,
check the water hardness of your domestic
system
Water hardness
If the water hardness in your area is high or
moderate, we recommend that you use a water
softener for washing machines. In areas where
Care and cleaning
the water hardness is soft it is not necessary to
use a water softener.
To know the water hardness in your area,
contact your local water authority.
Use the correct quantity of the water softener.
Obey the instructions that you find on the
packaging of the product.
WARNING!
Refer to Safety chapters.
External cleaning
Clean the appliance only with soap and warm
water. Fully dry all the surfaces.
CAUTION!
Do not use alcohol, solvents or
chemical products.
Descaling
If the water hardness in your area is high or
moderate, we recommend that you use a water
softener for washing machines.
Regularly examine the drum to prevent limescale
and rust particles.
To remove rust particles use only special
products for washing machine. Do this
separately from the laundry wash.
Always obey the instructions that
you find on the packaging of the
product.
Maintenance wash
With the low temperature programmes it is
possible that some detergent stays in the drum.
Make regularly a maintenance wash. To do this:
• Remove the laundry from the drum.
• Set the cotton programme with the highest
temperature with a small quantity of
detergent.
Door seal
Regularly examine the
seal and remove all
objects from the inner
part.
Cleaning the detergent dispenser
1 2
3 4
5 6
14 www.zanussi.com
Page 15
Cleaning the inlet hose and the valve
1
2
3
45°
20°
filter
1 2
Do this procedure also when you
want to do the emergency drain.
1. Disconnect the mains plug from the mains
socket.
2. Remove the water inlet hose.
3. Remove the drain hose from the rear
support and unhook it from sink or spigot.
4. Put the ends of the drain and inlet hose in a
container. Let the water flow out of the
hoses.
3
4
Frost precautions
If the appliance is installed in an area where the
temperature can be less than 0 °C, remove the
remaining water from the inlet hose and the
drain pump.
Troubleshooting
WARNING!
Refer to Safety chapters.
Introduction
The start of the appliance does not occur or it
stops during operation.
First try to find a solution to the problem (refer
to the table). If not, contact the Authorised
Service Centre.
With some problems, the acoustic signals
operate and the display shows an alarm
code:
5. When no more water flows, install the inlet
hose and the drain hose again.
WARNING!
Make sure that the temperature is
more than 0 °C before you use the
appliance again. The manufacturer is
not responsible for damages caused
by low temperatures.
• - The appliance does not drain the
water.
• - The appliance door is open or not
closed correctly. Please check the door!
• - The mains supply is unstable. Wait
until the mains supply is stable.
• - No communication between
electronic elements of the appliance. Switch
off and switch on again.
WARNING!
Deactivate the appliance before you
do the checks.
- The appliance does not fill with water
•
properly.
www.zanussi.com 15
Page 16
Possible failures
Problem Possible solution
The programme does not
start.
The appliance does not fill
with water properly.
The appliance does not drain
the water.
The spin phase does not operate or the washing cycle
lasts longer than usually.
There is water on the floor.
You cannot open the appliance door.
The appliance makes an unusual noise.
• Make sure that the mains plug is connected to the mains socket.
• Make sure that the appliance door is closed.
• Make sure that there is not a damaged fuse in the fuse box.
• Make sure that the Start/Pause has been pressed.
• If the delay start is set, cancel the setting or wait for the end of countdown.
• Deactivate the Child Lock function if it is on.
• Make sure that the water tap is open.
• Make sure that the pressure of the water supply is not too low. For
this information, contact your local water authority.
• Make sure that the water tap is not clogged.
• Make sure that the filter of the inlet hose and the filter of the valve are
not clogged. Refer to “Care and cleaning”.
• Make sure that the inlet hose has no kinks or bends.
• Make sure that the connection of the water inlet hose is correct.
• Make sure that the sink spigot is not clogged.
• Make sure that the drain hose has no kinks or bends.
• Make sure that the connection of the drain hose is correct.
• Set the drain option if you set a programme without drain phase.
• Set the drain option if you set an option which ends with water in the
drum.
• If above mentioned solutions do not help, contact the Authorised
Service Centre (as the filter of the drain pump may be clogged).
• Adjust manually the items in the tub and start the spin phase again.
This problem may be caused by balance problems.
• Set the spin option.
• Set the drain option if you set an option which ends with water in the
drum.
• If above mentioned solutions do not help, contact the Authorised
Service Centre (as the filter of the drain pump may be clogged).
• Make sure that the couplings of the water hoses are tight and there is
not water leakages.
• Make sure that the water inlet hose and the drain hose have no damages.
• Make sure you use the correct detergent and the correct quantity of
it.
• Make sure that the washing programme is finished.
• Set the drain or the spin option if there is water in the drum.
• Do the emergency drain procedure. See "Frost precautions" (in "Care
and Cleaning" chapter).
• Make sure the levelling of the appliance is correct. Refer to 'Installation instruction'.
• Make sure that the packaging and/or the transit bolts are removed.
Refer to 'Installation instruction'.
• Add more laundry in the drum. The load may be too small.
16 www.zanussi.com
Page 17
Problem Possible solution
The appliance fills with water
and drain immediately.
The cycle is shorter than the
time displayed.
The cycle is longer than the
time displayed.
The washing results are not
satisfactory.
You cannot set an option.
After the check, activate the appliance. The
programme continues from the point of
interruption.
If the problem occurs again, contact the
Authorised Service Centre.
If the display shows other alarm codes.
Deactivate and activate the appliance. If the
• Make sure that the drain hose is in the correct position. The end of
the hose may be too low. Refer to 'Installation instruction'.
• The appliance calculates a new time according to the laundry load.
See the ‘Consumption Values’ chapter.
• An unbalanced laundry load increases the duration time. This is a normal behaviour of the appliance.
• Increase the detergent quantity or use a different detergent.
• Use special products to remove the stubborn stains before you wash
the laundry.
• Make sure that you set the correct temperature.
• Decrease the laundry load.
• Make sure that you press only the wanted touch button(s).
Service
We recommend the use of original spare parts.
When contacting the Authorised Service
Centre, make sure that these data are available.
You can find the information on the rating plate:
model (Mod.), PNC (Prod.No.), Serial number
(Ser.No.).
problem continues, contact the Authorised
Service Centre.
Technical Data
Dimension Width/ Height/ Depth/ Total
depth
Electrical connection Voltage
Overall power
Fuse
Frequency
Level of protection against ingress of solid particles and
moisture ensured by the protective cover, except where the
low voltage equipment has no protection against moisture
Water supply pressure Minimum
Maximum
Water supply
Maximum Load Cotton 7 kg
Energy Efficiency Class A+++
1)
600 mm/ 850 mm/ 517 mm/ 576 mm
230-240 V
2200 W
13 A
50 Hz
IPX4
0,5 bar (0,05 MPa)
8 bar (0,8 MPa)
Cold water
www.zanussi.com 17
Page 18
Spin Speed Maximum 1200 rpm (ZWF 71263W)
1400 rpm (ZWF 71463W)
1) Connect the water inlet hose to a water tap with a 3/4'' thread.
ENVIRONMENTAL CONCERNS
Recycle the materials with the symbol . Put
the packaging in applicable containers to
recycle it. Help protect the environment and
human health and to recycle waste of electrical
and electronic appliances. Do not dispose
appliances marked with the symbol with the
household waste. Return the product to your
local recycling facility or contact your municipal
office.
18 www.zanussi.com
*
Page 19
www.zanussi.com 19
Page 20
www.zanussi.com/shop
192974450-A-052014
Loading...