Before the installation and use, read this manual carefully:
• For your personal safety and the safety of your property
• For the respect of the environment
• For the correct operation of the appliance.
Always keep these instructions with the appliance also if
you move or sell it.
The manufacturer is not responsible if incorrect installation or use results in damage.
Children and vulnerable people safety
• This appliance can be used by children aged from 8
years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision or
instruction concerning use of the appliance in safe way
and understand the hazards involved. Children shall
not play with the appliance.
• Keep all packaging away from children. There is the
risk of suffocation or physical injury.
• WARNING: Keep children and animals away from the
appliance when the door is open or the appliance is in
the operation, because it becomes hot. There is the risk
of injury or other permanent disability.
• If the appliance has Child Lock or Key Lock (Control
Lock) function, use it. It prevents children and animals
from accidental operation of the appliance.
General safety
• Do not change the specifications of this appliance.
There is the risk of injury and damage to the appliance.
• Do not let the appliance stay unattended during operation.
• Only an approved electrician can install and connect
the appliance. Contact an approved service centre. This
is to prevent the risks of structural damage or physical
injury.
• Make sure that the appliance is not damaged because
of transport. Do not connect a damaged appliance. If
necessary, contact the supplier.
• Remove all packaging, stickers and layers from the appliance before first use. Do not remove the rating plate.
It can invalidate the guarantee.
• Fully obey the laws, ordinances, directives and standards in force in the country where you use the appliance (safety regulations, recycling regulations, electrical or gas safety rules etc.).
• Make sure that the appliance is disconnected from the
power supply during the installation.
• Be careful when you move the appliance. The appliance
is heavy. Always use safety gloves. Do not pull the appliance by the handle.
• The electrical installation must have an isolation device
which lets you disconnect the appliance from the
mains at all poles. The isolation device must have a
contact opening width of minimum 3 mm.
• You must have correct isolation devices: line protecting cut-outs, fuses (screw type fuses removed from the
holder), earth leakage trips and contactors.
• The shock protection parts must be fixed in such a way
that they cannot be undone without tools.
• Some parts of the appliance carry current. Close the
appliance with furniture and make sure that there are
no free spaces. It prevents electrical shock because you
cannot accidentally touch dangerous parts.
2
www.zanussi.com
• Before the installation, make sure that the kitchen cabinet has the recess dimensions applicable.
• Make sure that the appliance is installed below and adjacent safe structures.
• Keep the minimum distances to the other appliances
and units.
• Install the appliance with its back and one side close to
the higher appliance. The other side must be close to
appliance with the same height.
• The appliance cannot be positioned on a base.
Electrical connection
• The appliance must be earthed.
• Make sure that the electrical data on the rating plate
agree with your domestic power supply.
• Information on the voltage is on the rating plate.
• Always use a correctly installed shockproof socket.
• When you connect electrical appliances to mains sockets, do not let cables touch or come near the hot appliance door.
• Do not use multi-way plugs, connectors and extension
cables. There is the risk of fire.
• Do not replace or change the mains cable. Contact the
service centre.
• Make sure not to squash or cause damage to the mains
plug (if applicable) and cable behind the appliance.
• Make sure that the mains connection is accessible after
the installation.
• Do not pull the mains cable to disconnect the appliance. Always pull the mains plug – if applicable.
• Fully close the oven door before you connect the appliance to mains.
Use
• The appliance is only for domestic use. Do not use the
appliance for commercial and industrial use.
• Only use the appliance for domestic cooking tasks.
This is to prevent physical injury to persons or prevent
damage to property.
• Do not use the appliance as a work surface or storage
surface.
• Do not put flammable products or items that are wet
with flammable products, and/or fusible objects (made
of plastic or aluminium) in, near or on the appliance.
There is the risk of explosion or fire.
• The interior of the appliance becomes hot during use.
There is the risk of burns. Do not touch the heating elements in the appliance. Use gloves when you insert or
remove the accessories or pots.
• Be careful when you remove or install the accessories
to prevent damage to the oven enamel.
• Always stay away from the appliance when you open
the door while the appliance is in operation. Hot steam
can release. There is the risk of skin burns.
• Discoloration of the enamel has no effect on the performance of the appliance so it is not a defect in the
sense of the warranty law.
• To prevent damage or discoloration to the enamel:
– Do not put any objects directly on the appliance
floor and do not cover it with aluminium foil.
– Do not put water directly into the hot appliance.
– Do not keep moist dishes and food in the appliance
after you finish the cooking.
• Do not use this appliance if it is in contact with water.
Do not operate the appliance with wet hands.
• Do not apply pressure on the open door.
• Always close the appliance door when you cook, even
while grilling.
Care and cleaning
• Before maintenance, switch off the appliance and disconnect the appliance from the power supply.
• Before maintenance, make sure that the appliance is
cold. There is the risk of burns. There is the risk that
the glass panels can break.
• Keep the appliance clean at all times. A build-up of fats
or other foodstuff can result in a fire.
• Regular cleaning prevents the surface material from deteriorating
• Use a deep baking tray for very moist cakes to prevent
that fruit juices cause stains that can be permanent.
• For your personal safety and the safety of your property, only clean the appliance with water and a soap. Do
not use flammable products or products that can cause
corrosion.
• Do not clean the appliance with steam cleaners, highpressure cleaners, sharp objects, abrasive cleaning
agents, abrasive sponges and stain removers
• If you use an oven spray, follow the instructions from
the manufacturer.
www.zanussi.com
3
• Do not clean the glass door with abrasive cleaning
agents or metal scraper. Heat resistant surface of the
inner glass can break and shatter.
• When the door glass panels are damaged they become
weak and can break. You must replace them. Contact
the service centre.
• Be careful when you remove the door from the appliance. The door is heavy!
• Do not clean catalytic enamel (if applicable).
Pyrolytic cleaning
Warning! Risk of burns.
• Keep children away from the appliance while the Pyrolytic cleaning is in operation. The appliance becomes
very hot.
• Provide good ventilation during and after each Pyrolytic cleaning.
• Remove any pets (especially birds) from the vicinity of
the oven location during and after the Pyrolytic cleaning and first use maximum temperature operation to a
well ventilated area.
• Read carefully all the instructions for Pyrolytic cleaning.
Risk of fire
• Open the door carefully. The use of ingredients with alcohol can cause a mixture of alcohol and air. There is
the risk of fire.
• Do not let sparks or open flames come near the appliance when you open the door.
• Do not put flammable products or items that are wet
with flammable products, and/or fusible objects (made
of plastic or aluminium) in, near or on the appliance.
Oven lamp
• The type of light bulb or halogen lamp used for this appliance is only for household appliances. Do not use it
for house lighting.
• If it becomes necessary to replace the lamp, use one of
the same power and specifically designed for household appliances only.
• Disconnect the appliance from the power supply before
the replacement of the oven lamp. There is the risk of
electrical shock.
Service centre
• Only an approved engineer can repair or work on the
appliance. Contact an approved service centre.
• Use only original spare parts.
Disposal of the appliance
• To prevent the risk of physical injury or damage
– Disconnect the appliance from the power supply.
– Cut off the mains cable and discard it.
– Discard the door catch. This prevents children or
small animals from being closed inside of the appliance. There is the risk of suffocation.
Product description
General overview
5
4
3
9
2
1
4
Knob for the oven functions
1
Electronic programmer
2 31
4
5
6
2
Knob for the temperature
3
Grill
4
Oven lamp
5
Fan
6
Shelf support, removable
7
Rating plate
8
Shelf positions
9
Oven accessories
78
• Wire shelf
For cookware, cake tins, roasts.
• Standard deep grill/roasting pan
www.zanussi.com
To bake and roast or as a pan to collect fat.
• Grill trivet
To roast and grill.
Before first use
Use the trivet only with the roasting pan.
Warning! Refer to "Safety information" chapter.
Initial cleaning
• Remove all accessories and removable shelf supports
(if applicable).
• Clean the appliance before first use.
Important! Refer to the chapter "Care and cleaning".
Setting the time of day
The display shows and 12:00. 12 flashes.
1.Press + or - to set the correct hour.
2.
3.Press + or - to set the correct minutes.
4.
to confirm. This is necessary only when
Press
you first set the time. Afterwards, the new time value
is saved automatically after five seconds.
The display shows
flashes.
to confirm. This is necessary only when
Press
you first set the time. Afterwards, the new time value
is saved automatically after five seconds.
and the set hour. 00
Daily use
Warning! Refer to "Safety information" chapter.
To use the appliance, push the knob. The knob comes out.
Activating and deactivating the appliance
1.Turn the knob for the oven functions to an oven
function.
Oven functions
The display shows the new time.
Changing the time of day
You can change the time of day only if the appliance
is off.
again and again until the indicator for the time
Press
of day
low the procedure given in "Setting the time of day".
flashes in the display. To set the new time, fol-
Preheating
Preheat the empty appliance to burn off the remaining
grease.
1.
Set the function
2.Let the appliance operate for 45 minutes.
3.
Set the function
4.Let the appliance operate for 15 minutes.
Accessories can become hotter than usually. The appliance can emit an odour and smoke. This is normal. Make
sure that the airflow is sufficient.
2.Turn the knob for the temperature to set the temperature.
3.To deactivate the appliance, turn the knob for the
oven functions to the off position.
and the maximum temperature.
and the maximum temperature.
Oven functionApplication
True Fan Cooking
Conventional Cooking
www.zanussi.com
Off positionThe appliance is off.
To roast or roast and bake food with the same cooking temperature, on more than
one shelf, without flavour transference.
To bake and roast on one oven level. The top and bottom heating elements oper-
ate at the same time.
5
Oven functionApplication
Grilling
Fast Grilling
Turbo Grilling
Pizza SettingTo make pizza, quiche or pie.
MeatTo prepare very tender and juicy roasts.
Keep WarmTo keep the food warm.
DefrostTo thaw frozen food.
To grill flat food items in small quantities in the middle of the shelf. To make
toast.
To grill flat food items in large quantities. To make toast. The full grill element
operates.
To cook large pieces of meat. The grill element and the oven fan operate one after
the other and circulate hot air around the food.
Pyro Cleaning
To clean the oven. The high temperature burns off the residual dirt. You can then
remove it with a cloth when the appliance is cold.
Display
Timer
1
Heat-up and residual heat indicator
2
Water tank (selected models only)
3
Food probe (selected models only)
4
Door lock (selected models only)
5
Hours/minutes
6
Clock functions
7
Buttons
ButtonFunctionDescription
ClockTo set a clock function.
,
Heat-up and residual heat indicator
When you activate an oven function, the bars in the dis-
come on one by one. The bars show that the oven
play
temperature increases or decreases.
Minus, plusTo set the time.
When you deactivate the appliance, the display shows the
residual heat indicator
more than 40 °C. Turn the temperature knob left or right
to show the oven temperature on the display.
1723
4567
if the temperature in the oven is
6
www.zanussi.com
Clock functions
SymbolFunctionDescription
Minute MinderTo set a countdown time.
Time of dayTo set, change or check the time of day. Refer to "Setting the time of day".
DurationTo set how long the appliance must operate. First set an oven function before you
set this function.
EndTo set when the appliance must be deactivated. First set an oven function before
you set this function. You can use Duration and End at the same time (Time Delay) to set the time when the appliance must be activated and then deactivated.
Press again and again to change the clock function.
to confirm the settings of the clock func-
Press
tions, or wait 5 seconds for the setting to be con-
firmed automatically.
Setting the Duration or End function
1.
2.Press + or - to set the minutes.
3.
4.Press + or - to set the hour.
5.
6.
function.
again and again until the symbol or
Press
flashes in the display.
to confirm.
Press
to confirm.
Press
When the set time ends, the symbol
the set time flash. The acoustic signal sounds for
two minutes. The appliance deactivates. Press a button or open the appliance door to stop the signal.
If you press
, the appliance switches to setting the End
while setting the time for Duration
or and
Setting the Minute Minder
Used to set a countdown time. The maximum time you
can set is 23 hours 59 minutes. This function has no ef-
fect on the operation of the oven. You can set the Minute
Minder at any time, also if the appliance is off.
1.
2.Press + or - to set the Minute Minder. At first the
3.The Minute Minder starts automatically after five
4.When the set time ends, the acoustic signal sounds
on in the display.
again and again until and 00 flash in
Press
the display.
time is calculated in minutes and seconds. When the
time you set is longer than 60 minutes, the symbol
comes on in the display. The appliance then
calculates the time in hours and minutes.
seconds.
for two minutes. 00:00 and
Press a button to stop the signal.
If you set the Minute Minder when the Duration
or End function operates, the symbol comes
flash in the display.
Count Up Timer
Use the Count Up Timer to monitor how long the oven operates. It is on immediately when the oven starts to heat.
To reset the Count Up Timer, press and hold + and -. The
timer starts to count up again.
You cannot use the Count Up Timer when the Dura-
or End function operates.
tion
Using the accessories
Warning! Refer to "Safety information" chapter.
www.zanussi.com
Trivet and grill/roasting pan
Warning! Be careful when you remove the
accessories from a hot appliance. There is a risk of
burns.
7
To grill flat food items and to make toast:Put the trivet in the grill/roasting pan so that the supports
point down.
Put the grill/roasting pan in the oven at the necessary level.
Additional functions
Child Lock
When the Child Lock is on, you cannot operate the oven.
This is to make sure that children do not accidentally activate the appliance.
Activating and deactivating the Child Lock function:
1.Do not set an oven function.
2.
Press and hold
seconds.
3.
An acoustic signal sounds. SAFE and
or go out in the display (when you activate or deactivate the Child Lock).
If the oven has the Pyro Cleaning function, the door
is locked.
SAFE and
knob or press a button.
come on in the display when you turn a
and + at the same time for two
come on
Automatic switch-off
For safety reasons the appliance deactivates after some
time:
• If an oven function operates.
• If you do not change the oven temperature.
Oven temperatureSwitch-off time
30 - 120 °C12.5 h
Oven temperatureSwitch-off time
120 - 200 °C8.5 h
200 - 250 °C5.5 h
250 - maximum °C3.0 h
After an automatic switch-off, press a button to activate
the appliance again.
Important! The automatic switch-off works with all oven
functions, except Light, Duration, End and Time Delay.
Cooling fan
When the appliance operates, the cooling fan activates automatically to keep the surfaces of the appliance cool. If
you deactivate the appliance, the cooling fan continues to
operate until the temperature in the appliance cools down.
Safety thermostat
Incorrect operation of the appliance or defective components can cause dangerous overheating. To prevent this,
the oven has a safety thermostat which interrupts the power supply. The oven activates again automatically when
the temperature drops.
Helpful hints and tips
• The appliance has five shelf levels. Count the shelf lev-
els from the bottom of the appliance floor.
• The appliance has a special system which circulates
the air and constantly recycles the steam. With this
system you can cook in a steamy environment and
keep the food soft inside and crusty outside. It decrea-
8
ses the cooking time and energy consumption to a
minimum.
• Moisture can condense in the appliance or on the door
glass panels. This is normal. Always stand back from
the appliance when you open the appliance door while
www.zanussi.com
Loading...
+ 16 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.