Zanussi ZK22/11LP, ZK22/11RD, ZK22/11LR User Manual
FRIGORÍFICO - CONGELADOR
REFRIGERATOR-FREEZER
FRIGORIFICO - CONGELADOR
ZK 22/11RD - ZK 22/11LR
ZK 22/11LP
214.3629.14
LIBRO DE INSTRUCCIONES
INSTRUCTION BOOKLET
INTRUÇÕES DE USO
ES
GB
PO
1
15
29
m
Warnings for your safety
Warnings for your safety. Carefully read
these instructions before installing and
using the machine.
m This freezer is designed to be operated by adults
only. Children should not be allowed to tamper with
the controls or play with the product.
m Any electrical work required to install the applian-
ce should be carried out by a qualified electrician or
competent person.
m This appliance is heavy. Care should be taken when
moving it.
m Make sure that the cable is not trapped underneath
the appliance, nor touches the motor.
m Repairs carried out by inexperienced persons may
cause injuries or serious malfunctioning. Refer to
the nearest Authorized Dealer.
m Make sure the rear part of the appliance stands
against a wall as there are working parts which heat
up and should not be of easy access.
m Frozen food must not be re-frozen once it has
been thawed out.
m Manufacturers storage recommendations
should be strictly complied with.
m Lollies can cause frost burns if consumed right
away from the freezer.
m Do not place carbonate or fizzy drinks in the
freezer as these may explode.
m When an old freezer is to be discarded make
sure to:
m Dismount the doors in order to prevent chil-
dren from getting trapped inside.
Have the gas from the cooling system with-
drawn before making it to scrap iron.
m Make sure that there is a continous and adequate
ventilation as a failure to do so may result in damage to the appliance or deterioration of the food.
m The appliance should be left for at least 4 hours
after installation before it is turned on ill order to
allow the refrigerant to settle.
m This product must be serviced only by an AUTHO-
RIZED DEALER, and only GENUINE SPARE
PARTS must be employed.
m Before cleaning or reparing the appliance, make
sure it is unplugged.
m It is dangerous to alter the specifications or modify
this product in any way.
m These domestic refrigerators are designed to be used
specifically forthe storage andconservation of food.
m DO NOT USE SHARP INSTRUMENTS to scrap
off frost or ice. Frost may be removed by using a
plastic scraper. (See defrosting instructions).
15
Índex
Warnings for your safety pag. 15
Installation pag. 17
Changing the opening directions
of the doors and Panelling pag. 18
Regulation and Control pag. 19
How to use your
Refrigerator-Freezer pag. 20 - 21
Maintenance of your
Refrigerator-Freezer pag. 22 - 23
Something not working pag. 24 - 25
Normal noises when
functioning pag. 26
Guarantee, Service
and Spare Parts pag. 27
Technical Features pag. 28
16
Installation
Positioning
Place the refrigerator away from direct sunlight and
heat sources.
Maintain recommended ventilation - see Fig. 1.
Make sure the refrigerator is accurately levelled tur-
ning the adjustable feet in order to avoid vibrations
and noises.
This is a built in design to be aligned with other fur-
niture
Cleaning the interior
Do not use alcohol or any cleanig product containing
alcohol because it can damage the cabinet.
Before using the appliance for the first time wash the
interior whith luke warm water and some neutral
soap so as to remove the typical smell of a brand-
new product arid then dry thoroughly.
Do not use detergents or abrasive powders as these
will damage the finish.
Remove security used for transportation.
Fig. 1
Electrical connection
mBefore plugging the appliance make sure that the
voltage and frequency shown on the «Technical
Features» correspond to your home supply.
mIt is essential that the appliance be efficiently
earthed.
For this purpose the supply cable plug incorporates
a special earth contact. If the sockets of your domes-
tic wiring system are not grounded, have the
appliance connected to a separate ground wire in
accordance with existing safety regulations.
«THE MANUFACTURER DECLINES TO
ACCEPT ANY LIABILITY IF THIS SAFETY
RULE IS NOT OBSERVED».
mShould a change of the supply cord be necessary,
remove the lid of the terminal board acting on «E»
and «F» as shown figure 3 in order to gain access to
the terminals. Fig. 3.
Starting up
Plug the appliance into the mains.
Make sure the inner light «H» turns on when ope-
ning the door.
Turn to intermediate position the knobs of the «tem-
perature regulators» «f» for refrigerating compart-
ment and «e» for freezing compartment.
Fig. 2
Fig. 3
17
Changing the opening direction
of doors and Panelling
If you wish to change the opening side of the doors
proceed as follows:
1... Take off the plinth pressed onto cabinet. (In some
models).
2... Remove the lower hinge taking care for the lower
door not to fall off.
3... Lift the lower door off the central hinge.
4... Remove the central hinge taking care for the upper
door not to fall off and not to lose the plastic
washer.
5... Take the upper door off the upper hinge. Be care-
full not to lose the plastic washer.
6... Unscrew the plastic plugs located on the opposite
side of the central hinge and introduce them in the
holes occupied before by the hinge.
7... Unscrew the axle of the upper hing and screw it
into the hinge on the opposite side. Make sure to fit
in the metal washer for blocking.
8... Place upper door.
For the remaining parts proceed the other way
round.
Once finished make sure that all joints close
perfectly well all around the door and chek that the
internal light turns of when the fridge door closes.
How to panel the door:
If your appliance is provided with metal strips for
panelling and you wish to do so proceed as follows:
1... Remove one of the side strips.
2... Loosen the screws of the remaining strips.
3... Start putting on the panel where you took off the
strip pushing it right up to the end.
Fig. 6
Fig. 7
4... Replace the strip on this side.
5... Tighten all screws
NOTE:
than the doors. Maximun thickness of the panel is 4 mm.
18
The panel dimensions must be 2 mm. shorter
Loading...