Zanussi ZHP612WM User Manual

Part 1 - INSTALLATION INSTRUCTIONS

1 - GENERAL INFORMATION

This cooker hood is designed to be fitted into the bottom of a cabinet positioned over a cooking area.
It must be connected to a remote blower, which may be positioned either inside or outside the home.
Before starting the installation, consideration should be given to the difficulties to be found during
installation. The installation work must be undertaken by a qualified and competent person in
conformity to the rules concerning the evacuation of contaminated air.

The manufacturer disclaims all liability for any damage or injury caused as a result of not following
the instructions for installation contained in the following text.

2 - SAFETY WARNINGS

2.1- When used in the extraction mode, the cooker hood ducting must not be connected to a
flue which is used for exhausting fumes from appliances supplied with energy other than
electric, such as a central heating flue or water heating flue.

2.2- Before connecting to the mains supply ensure that the mains voltage corresponds with
the voltage on the rating plate inside the hood.

2.3- Connect the cooker hood to the mains via a bipolar switch which has 3 mm clearance
between the contacts.

2.4- The appliance must be earthed.

2.5- When installed, the hood must be positioned at least 65 cm above the hotplate.

2.6- Never do flambé cooking under this cooker hood.

2.7- Never leave frying pans unattended during use as overheated fat and oil may catch fire.

2.8- Before carrying out any kind of maintenance or cleaning, disconnect the hood from the
mains supply.

2.9- If the room where the cooker hood is to be used contains a fuel burning appliance such
as a central heating boiler then this must be of the room sealed or balanced flue type. If
other types of flue or appliance are fitted, ensure that there is an adequate supply of air
into the room. When the cooker hood is used in conjunction with appliances supplied
with energy other than electric, the negative pressure in the room must not exceed 0,04
mbar to prevent fumes being drawn back into the room by the cooker hood.

3 - INSTALLATION

3.1 - Installation with screws

1 - The bottom of the cabinet must be placed at 135mm from the lower edges (fig. 1).
2 - The installer may choose one of the two sets of pre-drilled holes on the upper part of the canopy

hood (fig. 2).

3 - Drill 4.5mm Ø holes on the bottom of the cabinet in line with the chosen set of holes.
4 - Fix the cooker hood by using 4,2x44,4 four screws supplied (fig. 3).

3.2 - Installation with butterfly quick fixing system

1- The cooker hood can be provided with the butterfly quick fixing system S (fig. 4). If the cooker

hood is provided with this method of fixing the hood can be installed into the wall cabinet with the
bottom in its normal position.

2 - Make an opening on the bottom of the cabinet in accordance with the dimensions of the cooker

hood to be installed, paying attention to leave at least 15mm from the lower edge of the cabinet (fig.

5).

3 - Fit the cooker hood in the opening ensuring that the butterfly brackets S are hooked to the bottom

of the cabinet.

4 - Finally fix the hood by turning the screws of the brackets S placed on the lower part of the appliance

(fig. 6).

5 - To remove the hood from the cabinet loosen the securing screws anti-clockwise. In this position the

catches of butterfly brackets S are in the closed position and the hood can be removed from the
opening.

3.3 - Installation of the wall infill spacer

After having fixed the hood to the cabinet, a supplied metal wall infill spacer can be fitted on the lower
part to close up the space between the back edge of the hood and the wall (fig. 7).

3.4 - Ducting to the remote blower

The hood must be ducted to the remote blower using either a rigid or a flexible duct Ø 150mm (fig. 8).
In this case it will be necessary to fit a Ø 150-120mm adapter to the hood outlet.
If the remote blower is installed inside the home, it must be ducted to the outside.

3.5 - Electrical connection and working test

1 - Safety measures 2.2, 2.3 and 2.4 of paragraph 2 must be strictly observed.
2 - Once the electrical connection has been completed, check that the worktop illumination, motor and

speed adjustment work properly. After installation of the hood, the sliding visor should be opened

for the first time using a certain amount of force, until the click indicating maximum extension is
heard.