Zanussi ZGG 62411 XA User Manual [ru]

EN

User manual 2

RU

Инструкция по
эксплуатации

Hob

Газовая варочная панель

14

ZGG62411

BY

RU

Contents

Safety information _ _ _ _ _ _ _ _ _ _ _ _ _ _ 2
Safety instructions _ _ _ _ _ _ _ _ _ _ _ _ _ _ 3
Product description _ _ _ _ _ _ _ _ _ _ _ _ _ 5
Daily use _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 5
Helpful hints and tips _ _ _ _ _ _ _ _ _ _ _ _ _ 6

Care and cleaning _ _ _ _ _ _ _ _ _ _ _ _ _ _ 7
Troubleshooting _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 8
Installation _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 9
Technical information _ _ _ _ _ _ _ _ _ _ _ _ 12
Environment concerns _ _ _ _ _ _ _ _ _ _ _ 13

Subject to change without notice.

Safety information

Before the installation and use of the appliance, carefully read the
supplied instructions. The manufacturer is not responsible if an in­correct installation and use causes injuries and damages. Always
keep the instructions with the appliance for future reference.

Children and vulnerable people safety

Warning! Risk of suffocation, injury or permanent disability.

• This appliance can be used by children aged from 8 years and
above and persons with reduced physical, sensory or mental ca­pabilities or lack of experience and knowledge if they are super­vised by an adult or a person who is responsible for their safety.

• Do not let children play with the appliance.

• Keep all packaging away from children.

• Keep children and pets away from the appliance when it operates
or when it cools down. Accessible parts are hot.

• If the appliance has a child safety device, we recommend that you
activate it.

• Cleaning and user maintenance shall not be made by children
without supervision.

General Safety

• The appliance and its accessible parts become hot during use.
Do not touch the heating elements.

• Do not operate the appliance by means of an external timer or
separate remote-control system.

2

www.zanussi.com

• Unattended cooking on a hob with fat or oil can be dangerous
and may result in fire.

• Never try to extinguish a fire with water, but switch off the appli­ance and then cover flame e.g. with a lid or a fire blanket.

• Do not store items on the cooking surfaces.

• Do not use a steam cleaner to clean the appliance.

• Metallic objects such as knives, forks, spoons and lids should not
be placed on the hob surface since they can get hot.

Safety instructions

Installation

Warning! Only a qualified person must

install this appliance.

• Remove all the packaging.

• Do not install or use a damaged appliance.

• Obey the installation instruction supplied

with the appliance.

• Keep the minimum distance from the other

appliances and units.

• Always be careful when you move the appli-

ance because it is heavy. Always wear safety
gloves.

• Seal the cut surfaces with a sealant to pre-

vent moisture to cause swelling.

• Protect the bottom of the appliance from

steam and moisture.

• Do not install the appliance adjacent to a

door or under a window. This prevents hot
cookware to fall from the appliance when the
door or the window is opened.

• If the appliance is installed above drawers

make sure that the space, between the bot­tom of the appliance and the upper drawer,
is sufficient for air circulation.

• The bottom of the appliance can get hot. We

recommend to install a non-combustile sepa­ration panel under the appliance to prevent
access to the bottom.

Electrical connection

www.zanussi.com

Warning! Risk of fire and electrical shock.

• All electrical connections must be made by a
qualified electrician.

• The appliance must be earthed.

• Before carrying out any operation make sure
that the appliance is disconnected from the
power supply.

• Use the correct electricity mains cable.

• Do not let the electricity mains cable tangle.

• Make sure the mains cable or plug (if appli­cable) does not touch the hot appliance or
hot cookware, when you connect the appli­ance to the near sockets

• Make sure the appliance is installed correct­ly. Loose and incorrect electricity mains ca­ble or plug (if applicable) can make the termi­nal become too hot.

• Make sure that a shock protection is instal­led.

• Use the strain relief clamp on cable.

• Make sure not to cause damage to the mains
plug (if applicable) or to the mains cable.
Contact the Service or an electrician to
change a damaged mains cable.

• The electrical installation must have an isola­tion device which lets you disconnect the ap­pliance from the mains at all poles. The isola­tion device must have a contact opening
width of minimum 3 mm.

• Use only correct isolation devices: line pro­tecting cut-outs, fuses (screw type fuses re-

3

moved from the holder), earth leakage trips
and contactors.

Gas connection

• All gas connections should be made by a
qualified person.

• Make sure that there is air circulation around
the appliance.

• The information about the gas supply is on
the rating plate.

• This appliance is not connected to a device,
which evacuates the products of combus­tion. Make sure to connect the appliance ac­cording to current installation regulations.
Pay attention to requirements regarding ade­quate ventilation.

Use

Warning! Risk of injury, burns or electric

shock.

• Use this appliance in a household environ­ment.

• Do not change the specification of this appli­ance.

• Do not let the appliance stay unattended
during operation.

• Do not operate the appliance with wet hands
or when it has contact with water.

• Do not put cutlery or saucepan lids on the
cooking zones. They become hot.

• Set the cooking zone to “off” after use.

Warning! Risk of fire or explosion.

• Fats and oil when heated can release flam­mable vapours. Keep flames or heated ob­jects away from fats and oils when you cook
with them.

• The vapours that very hot oil releases can
cause spontaneous combustion

• Used oil, that can contain food remnants, can
cause fire at a lower temperature than oil
used for the first time.

• Do not put flammable products or items that
are wet with flammable products in, near or
on the appliance.

4

Warning! Risk of damage to the

appliance.

• Do not keep hot cookware on the control
panel.

• Do not let cookware to boil dry.

• Do not activate the cooking zones with emp­ty cookware or without cookware.

• Be careful not to let objects or cookware fall
on the appliance. The surface can be dam­aged.

• Do not put aluminium foil on the appliance.

• Do not let acid liquids, for example vinegar,
lemon juice or limescale remover touch the
hob. This can cause matt patches.

• Provide good ventilation in the room where
the appliance is installed.

• Make sure that the ventilation openings are
not blocked.

• Use only stable cookware with the correct
shape and diameter larger than the dimen­sions of the burners. There is a risk of over­heating and rupture of the glass plate (if ap­plicable).

• Make sure the flame does not go out when
you quickly turn the knob from the maximum
to the minimum position.

• Make sure pots are centrally positioned on
the rings and do not stick out over edges of
the cooking surface.

• Use only the accessories supplied with the
appliance.

• Do not install a flame diffuser on the burner.

Care and Cleaning

Warning! Risk of damage to the

appliance.

• Clean regularly the appliance to prevent the
deterioration of the surface material.

• Do not use water spray and steam to clean
the appliance.

• Do not clean the burners in the dishwasher.

• Clean the appliance with a moist soft cloth.
Only use neutral detergents. Do not use
abrasive products, abrasive cleaning pads,
solvents or metal objects.

www.zanussi.com

Disposal

Warning! Risk of injury or suffocation.

• Contact your municipal authority for informa­tion on how to discard the appliance correct­ly.

Product description

Cooking surface layout

1 2

5 4 3

• Disconnect the appliance from the mains
supply.

• Cut off the mains cable and discard it.

• Flat the external gas pipes.

Semi-rapid burner

1

Semi-rapid burner

2

Control knobs

3

Auxiliary burner

4

Rapid burner

5

Control knobs

Symbol Description

no gas supply / off position

Daily use

Warning! Refer to the Safety chapters.

Ignition of the burner

Warning! Be very careful when you use

open fire in kitchen environment.
Manufacturer decline any responsibility in case
misuse of the flame

Always light the burner before you put

cookware.

To light the burner:

www.zanussi.com

Symbol Description

maximum gas supply

minimum gas supply

1. Push and hold the spark generator button
.

2. At the same time turn the control knob

counterclockwise to the maximum position

and push it down to light the burner.

3. Adjust the flame after it is regular.

If after some tries the burner does not
light, check if the crown and its cap are in

correct positions.

5

and try to light the burner again after minimum
1 minute.

A

B

C

A) Burner cap
B) Burner crown
C) Ignition candle

Warning! Do not keep the control knob

pushed for more than 15 seconds.
If the burner does not light after 15 seconds,
release the control knob, turn it into off position

Helpful hints and tips

Warning! Refer to the Safety chapters.

Energy savings

• If possible, always put the lids on the pans.

• When the liquid starts to boil, turn down the

flame to barely simmer the liquid.
Use cookware with diameters applicable to the
size of burners.

Important! In the absence of electricity you
can ignite the burner without electrical device;
in this case approach the burner with a flame,
push the relevant knob down and turn it
counter-clockwise to maximum gas release
position.

If the burner accidentally goes out, turn the
control knob to the off position and try to

light the burner again after minimum 1 minute.

The spark generator can start automatical­ly when you switch on the mains, after in-

stallation or a power cut. It is normal.

Turning the burner off

To put the flame out, turn the knob to the sym-

bol

.

Warning! Always turn the flame down or
switch it off before you remove the pans

from the burner.

Burner Diameters of cookware

Rapid 160 - 260 mm

Semi-rapid 120 - 220 mm

Auxiliary 80 - 160 mm

Warning! Make sure that the bottoms of

pots do not stand above the control
knobs. If the control knobs are under the
bottoms of pots, the flame heats them up.
Do not put the same pan on two burners.

6

Warning! Make sure that pot handles is

not above the front edge of the cooktop.
Make sure that pots are centrally put on the
rings in order to get maximum stability and to
get lower gas consumption.

Do not put unstable or damaged pots on the
rings to prevent from spill and injury.

Warning! Do not use a flame diffuser.

www.zanussi.com

Care and cleaning

Warning! Refer to the Safety chapters.

Warning! Deactivate the appliance and

let it cool down before you clean it.
Disconnect the appliance from the electrical
supply before you do cleaning or maintenance
work.

Warning! For safety reasons, do not clean

the appliance with steam cleaners or high­pressure cleaners.

Warning! Do not use abrasive cleaners,

steel wool pads or acids. They can cause
damage to the appliance.

Scratches or dark stains on the surface

have no effect on how the appliance oper­ates.

• You can remove the pan supports to easily

clean the hob.

• To clean the enamelled parts, cap and

crown, wash them with warm soapy water
and dry them carefully before you put them
back.

• Wash stainless steel parts with water, and

then dry them with a soft cloth.

• The pan supports are not dishwasher proof.

They must be washed by hand.

• When you wash the pan supports by hand,

take care when you dry them as the enamel­ling process occasionally leaves rough
edges. If necessary, remove stubborn stains
using a paste cleaner.

• Make sure you position the pan supports

correctly after cleaning.

• To make the burners work correctly, make
sure that the arms of the pan supports are in
the centre of the burner.

• Be very careful when you replace the

pan supports to prevent the hob top
from damage.

After cleaning, dry the appliance with a soft
cloth.

Removing the dirt:

1. – Remove immediately: melting plastic,

plastic foil, and food containing sugar.

– Stop the appliance and let it cool

down before you clean: limescale rings,
water rings, fat stains, shiny metallic dis­colorations. Use a special cleaner appli­cable for surface of hob.

2. Clean the appliance with a damp cloth and

some detergent.

3. At the end rub the appliance dry with a

clean cloth.

The stainless steel can become tarnished if it is
too much heated. Refer to this you must not
cook with potstones, earthenware pans or cast
iron plates.

Cleaning of the spark plug

This feature is obtained through a ceramic igni­tion candle with a metal electrode. Keep these
components well clean to prevent difficult light­ing and check that the burner crown holes are
not obstructed.

Periodic maintenance

Periodically speak your local Service Force
Centre to check the conditions of the gas sup­ply pipe and the pressure adjuster, if fitted.

www.zanussi.com

7

Troubleshooting

Problem Possible cause Remedy

There is no spark when lighting
the gas

• Burner cap and crown are

The gas ring burns unevenly • Burner crown is blocked with

• There is no electrical supply • Make sure that the unit is con-

placed uneven

food residues

nected and the electrical supply
is switched on.

• Control the fuse. If the fuse is
released more than one time,
refer to a qualified electrician.

• Make sure that the burner cap
and crown are in correct posi­tions.

• Make sure that the injector is
not blocked and the burner
crown is clear of food particles.

8

www.zanussi.com

If there is a fault, first try to find a solution to the
problem yourself. If you cannot find a solution to
the problem yourself, speak your dealer or the
local Service Force Centre.

If you operated the appliance incorrectly,

or the installation was not carried out by a
registered engineer, the visit from the customer
service technician or dealer may not take place
free of charge, even during the warranty period.

These data are necessary to help you
quickly and correctly. These data are
available on the supplied rating plate.

• Model description .................

1 2 3

• Product number (PNC) .................

• Serial Number (S.N.) .................

Use the original spare parts only. They are
available at Service Force Centre and approved
spare parts shops.

Labels supplied with the accessories bag

Stick the adhesive labels as indicated below:

MOD.

PROD.NO.

SER.NO

DATA

Stick it on Guarantee Card and send this

1

MOD.

PROD.NO.

SER.NO

DATA

MODELMODEL

part
Stick it on Guarantee Card and keep this

2

part

Installation

Warning! Refer to the Safety chapters.

Warning! The following instructions about

installation, connection and maintenance
must be carried out by qualified personnel in
compliance with standards and local
regulations in force.

0049

03 IT

MADE IN ITALY

MOD.
PROD.NO.
SER.NO.

Stick it on instruction booklet

3

TYPE
230V-50Hz
IP20

Gas Connection

Choose fixed connections or use a flexible pipe
in stainless steel in compliance with the regula­tion in force. If you use flexible metallic pipes,
be careful they do not come in touch with mo­bile parts or they are not squeezed. Also be
careful when the hob is put together with an
oven.

www.zanussi.com

9