Zanussi ZGF96XK User Manual

ENGLISH

For Your Safety

These warnings are provided in the interest of safety. You MUST read them carefully before installing or using the appliance. It is most important that this instruction book should be retained with the appliance for future reference. Should the appliance be sold or transferred, always ensure that the book is left with the appliance in order that the new owner can get to know the functions of the appliance and the relevant warnings.

Installation

•It is mandatory that all operations required for the installation are carried out by a qualified or competent person, in accordance with existing rules and regulations.

•It is dangerous to alter the specification in any way.

•Using a gas cooking appliance will produce heat and moisture in the room which it has been installed in. Ensure a continuous air supply, keeping the air vents in good conditions or installing a cooker hood with discharge tube.

•In case of intensive or long time use of the appliance, make the ventilation more efficient, by opening a window or increasing the electric exhaust fan power.

•Once you removed all packaging from the appliance, ensure that it is not damaged and the electric cable is in perfect conditions. Otherwise, contact your dealer before proceeding with the installation.

•Ensure that the gas supply complies with the gas type stated on the identification label, placed near the gas supply pipe.

•Ensure a good ventilation around the appliance. A poor air supply could cause lack of oxygen.

•The manufacturer disclaims any responsability should all the safety measures not be carried out.

Cleaning and Manteinance

•For hygiene and safety reasons, this appliance should be kept clean at all times. A build-up of fats or other foodstuff could result in a fire.

•Disconnect the appliance from the electrical supply, beforecarryingoutanycleaningormanteinancework.

Technical assistance

•Under no circumstances should you attempt to repair the appliance yourself. Repairs carried out by unexperienced persons may cause injury or serious malfunctioning. Refer to your local Service Centre. Always insist on genuine spare parts.

Environmental Information

•After installation, please dispose of the packaging with due regard to safety and the environment.

•Whendisposingofanoldappliance,makeitunusable, by cutting off the cable.

These instructions are only for the countries stated by the symbol printed on the front cover of this instruction book.

During Operation

•This appliance has been designed for cooking edible foodstuffandtobeusedfordomestic non-professional purposes only. It must not be used for any other purpose.

•Ensure that all control knobs are in the OFF position when not in use.

•Should you connect any electrical tool to a plug near this cooking appliance, ensure that electric cables are not in contact with it and keep them far enough from the heated parts of this appliance.

•If the appliance is out of order, disconnect it from the electric supply.

Child safety

•This appliance has been designed to be operated by

adults and children under supervision. Young children MUST NOT be allowed to tamper with the controls or play near or with the oven.

•Accessible parts of this appliance may become hot when it is in use. Children should be kept away until it has cooled.

Guide to Use the instructions

Thefollowingsymbolswillbefoundinthetexttoguideyou throughout the Instructions:

Safety Instructions

ΦStep by step instructions for an operation

Hints and Tips

Environmentalinformation

MANUFACTURER:

ELECTROLUX ZANUSSI S.p.A.

Viale Bologna 298 - 47100 FORLI’ (Italy)

Contents

For the user		For the installer
For Your Safety	12	Technical Data	15
Instruction for the User	13	Instruction for the Installer	15
Cleaning and Maintenance	14	Electrical Connection	16
		Adaptation to different types of gas	17
		Building in	18

Instruction for the User

Hob burners control knobs

The hob burners control knobs are situated on the hob lateral panel. The symbols on the knobs mean that :

λthere is no gas supply

there is maximum gas supply

there is minimum gas supply

Lighting the burners

Foreasierlighting,proceedbeforeputtingapanon the pan support.

Φλ To light a burner, push in the relevant control knob and turn it anti-clockwise to "maximum" position.

λUpon ignition, keep the knob pushed down for about 5 seconds. This will allow the "thermocouple" (Fig. 1 lett. D) to be heated and the safety device to be switched off, otherwise the gas supply would be interrupted.Then, check the flame is regular and adjust it as required.

λIf you cannot light the flame even after several attempts, check the "cap" (Fig. 1 lett. A) and the "crown" (Fig. 1 lett. B) are in the correct position.

λTo put the flame out, turn the knob to the symbol λ.

Always turn the flame down or put it out before taking the pans off the burner.

Fig. 1	FO 0204

A - Burner cap

B - Burner crown

C - Ignition candle

D - Thermocouple

Using the hob correctly

To ensure maximum burner efficiency, it is strongly recommended that you use only pots and pans with a flat bottom fitting the size of the burner used, so that flame will not spread beyond the bottom of the vessel (see the table beside). It is also advisable, as soon as a liquid starts boiling, to turn down the flame so that it will barely keep the liquid simmering.

Carefully supervise cookings with fats or oil, since these types of foodstuff can result in a

fire,ifover-heated.

Burner	minimum	maximum
	diameter	diameter

Big (rapid)	180 mm.	260 mm.
Medium (semirapid)	120 mm.	220 mm.
Small (Auxiliary)	80 mm.	160 mm.
Fish kettle	120x270 mm.	210x380mm.

Cleaning and Maintenance

Disconnect the appliance from the electrical supply, before carrying out any cleaning or

manteinance work.

General cleaning

Wash the enamelled components with warm soapy water. Never use abrasive cleaners.

Frequently wash the "caps" and the "crowns" with hot soapy water, carefully taking away any built-up of food. If the marks are particularly difficult to remove, use common non-abrasive cleaners or specific products.

Never use steel wool pads or acids.

Automatic ignition

The automatic ignition of the gas burners is obtained through a ceramic "candle" and a metal electrode (fig. 1 lett. C). Keep these components well clean, to avoid difficult lighting, and check that the burner crown holes (lett. B) are not obstructed.

Pan supports

To keep the pan supports in the right position, they are hooked to a couple of special hinges in the back of the hob. Thanks to these hooks, you can lift the pan supports for easier cleaning, as shown in fig. 2.

To take the pan supports completely off the hob, proceed as shown in fig. 3.

Cast iron pan supports

Caution! When removing the cast iron pan supports, lift them up as shown in fig. 3. Never turn the pan supports on the hinges as shown in fig. 2, since this could damage them.

Periodic Maintenance

Periodically ask your local Service Centre to check the conditions of the gas supply pipe and the pressure adjuster, if fitted.

To ensure the good operation of the hob and its safety features, it is necessary that the taps are periodically lubricated.

λThe periodic lubrication of the taps must be carried out by qualified personnel, which you must refer to also in case of malfunctioning.

FO 2030

Fig. 2

YES

Fig. 3

Mainteinance - Technical Assistance

ORIGINAL SPARE PARTS

This machine, before leaving the factory, has been tested and studied by many experts and specialists, in order to give you the best results.

Any repair work which needs to be carried out should be done with the utmost care and attention.

For this reason we reccomend that for any problem you contact the dealer who sold it to you, or our nearest authorized Service Centre, specifying the nature of the problem and the particular model which you own.

+ 6 hidden pages