Zanussi ZGF783ITXC User Manual

ENGLISH

For Your Safety

These warnings are provided in the interest of safety. You MUST read them carefully before installing or using the appliance.

It is most important that this instruction book should be retained with the appliance for future reference. Should the appliance be sold or transferred, always ensure that the book is left with the appliance in order that the new owner can get to know the functions of the appliance and the relevant warnings.

During Operation

•This appliance has been designed to be operated by adults and children under supervision. Young children MUST NOT be allowed to tamper with the controls or

play near or with the oven.

•This appliance has been designed for cooking edible foodstuff and to be used for domestic nonprofessional purposes only. It must not be used for any other purpose.

•It is dangerous to alter the specification in any way.

•For hygiene and safety reasons, this appliance should be kept clean at all times. A build-up of fats or other foodstuff could result in a fire.

•Accessible parts of this appliance may become hot when it is in use. Children should be KEPT AWAY until it has cooled.

•Under no circumstances should you attempt to repair the appliance yourself. Repairs carried out by unexperienced persons may cause injury or serious malfunctioning. Refer to your local Zanussi Service Centre. Always insist on genuine Zanussi spare parts.

•Ensure that all control knobs are in the OFF position when not in use.

•Should you connect any electrical tool to a plug near this cooking appliance, ensure that electric cables are not in contact with it and keep them far enough from the heated parts of this appliance.

•If the appliance is out of order, disconnect it from the electric supply.

MANUFACTURER:

ELECTROLUX ZANUSSI ELETTRODOMESTICI S.p.A.

Viale Bologna 298 - 47100 FORLI’ (Italy)

About Installation, Cleaning

and Manteinance

•It is mandatory that all operations required for the installation are carried out by a qualified or competent person, in accordance with existing rules and regulations.

•Disconnect the appliance from the electrical supply, before carrying out any cleaning or manteinance work.

•Ensure a good ventilation around the appliance. A poor air supply could cause lack of oxygen.

•Ensure that the gas supply complies with the gas type stated on the identification label, placed near the gas supply pipe.

•Using a gas cooking appliance will produce heat and moisture in the room which it has been installed in. Ensure a continuous air supply, keeping the air vents in good conditions or installing a cooker hood with discharge tube.

•In case of intensive or long time use of the appliance, make the ventilation more efficient, by opening a window or increasing the electric exhaust fan power.

•Once you removed all packaging from the appliance, ensure that it is not damaged and the electric cable is in perfect conditions. Otherwise, contact your dealer before proceeding with the installation.

•The manufacturer disclaims any responsability should all the safety measures not be carried out.

This appliance complies with the following E.E.C. Directives:

-73/23 - 90/683 (Low Voltage Directive);

-89/336 (Electromagnetical Compatibility Directive);

-90/396 (Gas Appliances)

-93/68 (General Directives) and subsequent modifications.

These instructions are only for the countries stated by the symbol printed on the front cover of this instruction book.

Contents

1.	Instruction for the User .............	Pag.	34
2.	Cleaning and Maintenance .......	Pag.	35
3.	Technical Data ...........................	Pag.	36
4.	Instruction for the Installer .......	Pag.	36

5.	Electrical Connection ................	Pag.	37
6.	Adaptation to different
	types of gas................................	Pag.	38
7.	Building In ..................................	Pag.	39
	Guarantee ...................................	Pag.	42

1. Instruction for the User

HOB BURNERS CONTROL KNOBS

The hob burners control knobs are situated on the hob front panel. The symbols on the knobs mean that :

●there is no gas supply

there is maximum gas supply

there is minimum gas supply

LIGHTING THE BURNERS

•For easier lighting, proceed before putting a pan on the pan support.

•In models provided with automatic ignition, depress the relevant switch marked with a small spark. Then, push the relevant knob down and turn it anti-clockwise until it reaches the "maximum" position.

•In models provided with semi-automatic ignition,push the relevant knob down and turn it anti-clockwise until it reaches the "maximum" position.

After lighting the flame, keep the knob pushed down for about 5 seconds. This will allow the "thermocouple" (Fig. 1 lett. D) to be heated and the safety device to be switched off, otherwise the gas supply would be interrupted. Then, check the flame is regular and adjust it as required.

If you cannot light the flame even after several attempts, check the "cap" (Fig. 1 lett. A) and the "crown" (Fig. 1 lett. B) are in the correct position. To put the flame out, turn the knob to the symbol ●.

•In the absence of electricity, ignition can occur without the electrical device; in this case approach the burner with a flame, push the relevant knob down and turn it anti-clockwise until it reaches the "maximum" position.

•Always turn the flame down or put it out before taking the pans off the burner.

USING THE HOB CORRECTLY

To ensure maximum burner efficiency, it is strongly recommended that you use only pots and pans with a bottom fitting the size of the burner used, so that flame will not spread beyond the bottom of the vessel (see the table beside).

It is also advisable, as soon as a liquid starts boiling, to turn down the flame so that it will barely keep the liquid simmering.

• Use only pans or pots with flat bottom.

Carefully supervise cookings with fats or oil, since these types of foodstuff can result in a fire, if over-heated.

Fig. 1	FO 0204

Burner	minimum	maximum
	diameter	diameter

Double Crown	180 mm.	260 mm.
Big (rapid)	180 mm.	260 mm.
Medium (semirapid)	120 mm.	220 mm.
Small (Auxiliary)	80 mm.	160 mm.

THE HOB LID

In order to make the appliance match with the kitchen design, a lid (not provided) can be fitted on the hob.

●The lid is meant to avoid dust to settle on the hob, when it is closed, and to collect splashes of oil or fat, when it is open. Do not use it for any other purpose.

●Always wipe off any splash of liquid before opening the lid.

●Always clean the lid from cooking residues before opening it or taking it off.

●WARNING! The crystal lid can splinter when overheated. Always ensure all the burners are off before closing it.

2. Cleaning and Maintenance

• Disconnect the appliance from the electrical supply, before carrying out any cleaning or manteinance work.

Wash the enamelled components with warm soapy water. Never use abrasive cleaners

Frequently wash the "caps" and the "crowns" with hot soapy water, carefully taking away any built-up of food. Carefully wash the stainless steel components with water, then wipe them dry with a soft cloth.

The pan supports are dishwasher proof.

If the marks are particularly difficult to remove, use common non-abrasive cleaners or specific products. Never use steel wool pads or acids.

In models provided with electric ignition, this feature is obtained through a ceramic "candle" and a metal electrode (fig. 1 lett. C). Keep these components well clean, to avoid difficult lighting, and check that the burner crown holes (lett. B) are not obstructed.

PAN SUPPORTS

To keep the pan supports in the right position, they are hooked to a couple of special hinges in the back of the hob.

Thanks to these hooks, you can lift the pan supports for easier cleaning, as shown in fig. 2.

To take the pan supports completely off the hob, proceed as shown in fig. 3.

CAST IRON PAN SUPPORTS(ZGF783 ITXC)

Caution!

When removing the cast iron pan supports, lift them up as shown in fig. 3. Never turn the pan supports on the hinges as shown in fig. 2, since this could damage them.

PERIODIC MAINTENANCE

Periodically ask your local Service Centre to check the conditions of the gas supply pipe and the pressure adjuster, if fitted.

To ensure the good operation of the hob and its safety features, it is necessary that the taps are periodically lubricated.

FO 2030

Fig. 2

FO 2238

Fig. 3

●The periodic lubrication of the taps must be carried out by qualified personnel, which you must refer to also in case of malfunctioning.

+ 7 hidden pages