Zanussi ZGF692CX, ZGF692CW, ZGF692CN User Manual

GAS HOBS

ZGF 682

ZGF 692

INSTRUCTION BOOKLET

Please read this instruction booklet before using the appliance

GB

Important Safety Information

You MUST read hese warnings carefully before installing or using the hob. If you need
assistance, contact our Customer Care Department on 08705 727727

Installation

z This appliance must be installed and serviced by a

competent person as stated in the Gas Safety (
Installation and Use) Regulations Current Editions
and the IEE Wiring Regulations.

z Remove all packaging before using the hob.

z Ensure that the gas and electrical supply complies

with the type stated on the rating plate, located near
the gas supply pipe.

z Do not attempt to modify the hob in any way.

Child Safety

z This hob is designed to be operated by adults. Do

not allow children to play near or with the hob.

z The hob gets hot when it is in use.

z Children should be kept away until it has cooled.

z Children can also injure themselves by pulling pans

or pots off the hob.

z Never use plastic or aluminium foil dishes on the hob.

z Perishable food, plastic items and aerosols may be

affected by heat and should not be stored above or
below the hob unit.

Service

z This hob should only be repaired or serviced by an

authorised Service Engineer and only genuine
approved spare parts should be used.

Environmental Information

z After installation, please dispose of the packaging with

due regard to safety and the environment.

z When disposing of an old appliance, make it unusable,

by cutting off the cable.

z The symbol on the product or on its packaging

During Use

z This hob is intended for domestic cooking only. It is

not designed for commercial or industrial purposes.

z This appliance is not connected to a combustion

products evacuation device. It must be installed and
connected in accordance with current installation
regulations. Particular attention shall be given to the
relevant requirements regarding ventilation.

z When in use a gas cooking appliance will produce

heat and moisture in the room in which it has been
installed. Ensure there is a continuous air supply,
keeping air vents in good condition or installing a
cooker hood with a venting hose.

z When using the hob for a long period of time, the

ventilation should be improved, by opening a window
or increasing the extractor speed.

z Do not use this hob if it is in contact with water.

Do not operate the hob with wet hands.

z Ensure the control knobs are in the ‘OFF’ position

when not in use.

z When using other electrical appliances, ensure the

cable does not come into contact with the hot surfaces
of the cooking appliance.

z Unstable or misshapen pans should not be used on

the hob as unstable pans can cause an accident by
tipping or spillage.

z Never leave the hob unattended when cooking with

oil and fats.

indicates that this product may not be treated as
household waste. Instead it shall be handed over to
the applicable collection point for the recycling of
electrical and electronic equipment. By ensuring this
product is disposed of correctly, you will help prevent
potential negative consequences for the environment
and human health, which could otherwise be caused
by inappropriate waste handling of this product. For
more detailed information about recycling of this
product, please contact your local city office, your
household waste disposal service or the shop where
you purchased the product.

Keep this instruction book for future reference

and ensure it is passed on to any new owner.

Guide to Use the instructions

The following symbols will be found in the text to guide
you throughout the Instructions:

Safety Instructions

Step by step instructions for an operation

)

Hints and Tips

Environmental Information

2

Contents

For the User

Important Safety Information 2

Description of the Hob 3

Operation 4

Maintenance and Cleaning 5

Something Not Working? 6

Service and Spare Parts 6

Customer Care 7

Guarantee Conditions 7

This appliance complies with the following

E.E.C. Directives:

* 73/23 - 90/683

(Low VoltageDirective);

* 93/68 (General Directives);
* 89/336 (Electromagnetical Compatibility Directive);
* 90/396 (Gas Appliances),

and subsequent modifications

For the Installer

Instructions for the Installer 8

Installation 10

Electrical connections 12

Wiring Diagram 13

Fault Finding 13

Commissioning 15

Conversion from Natural Gas to LPG 15

Description of the Hob

Model ZGF 692Model ZGF 682

3

2

3

1

4

5

1

5

3

2

3

4

1. Hob Top

2. Auxiliary Burner

3. Semi-rapid Burners

4. Ultra-rapid Triple-crown Burner

5. Control knobs

3

Operation

Hob burners

To light a burner:

)

z turn the relevant control knob anticlockwise to the

maximum position, then push it down to ignite the
burner;

z then, check the flame is regular and adjust it as

required.
If you cannot light the flame even after several attempts,
check the "cap" and “crown” (see Fig. 1 - letter A and
B) are in the correct position.
To put the flame out, turn the knob to the symbol z.

When switching on the mains, after installation
or a power cut, it is quite normal for the spark
generator to be activated automatically.

To ensure maximum burner efficiency, you should only
use pots and pans with a flat bottom fitting the size of
the burner used (see table).

Burner minimum maximum

diameter diameter

Ultra-rapid
(Triple-crown) 180 mm 260 mm
Medium (semi-rapid) 120 mm 220 mm
Small (Auxiliary) 80 mm 160 mm

If you use a saucepan which is smaller than
the recommended size, the flame will spread
beyond the bottom of the vessel, causing the
handle to overheat.

Take care when frying food in hot oil or fat,
as the overheated splashes could easily
ignite.

As soon as a liquid starts boiling, turn down the
flame so that it will barely keep the liquid
simmering.

Fig. 1

Triple-crown Burner

A

B

C

A - Burner cap
B - Burner crown
C - Ignition electrode

suitable for model ZGF 682

If the control knobs become difficult to turn, please
contact your local Service Force Centre.

Using the Wok Stand

A wok stand is provided to enable you to use a round
bottomed wok on the hob. The wok stand must only be
used on the front right burner, and should not be used
with any other type of wok or pan.
When fitting the wok stand, ensure the recesses in the
frame fit securely onto the bars of the pan supports, as
shown in the diagrams.

4

suitable for model ZGF 692

Maintenance and Cleaning

Before any maintenance or cleaning can be
carried out, you must DISCONNECT the hob
from the electricity supply.

The hob is best cleaned whilst it is still warm, as spillage
can be removed more easily than if it is left to cool.

The Hob Top

Regularly wipe over the hob top using a soft cloth well
wrung out in warm water to which a little washing up
liquid has been added. Avoid the use of the following:

- household detergent and bleaches;

- impregnated pads unsuitable for non-stick
saucepans;

- steel wool pads;

- bath/sink stain removers.

Should the hob top become heavily soiled, it is
recommended that a cleaning product such as Hob Brite
or Bar Keepers Friend is used.

Pan Supports

To keep the pan supports in the correct position, they
are hooked into hinges at the back of the hob.

Model ZGF 682: The pan supports can be lifted
for easier cleaning, as shown in Fig. 2.
To remove the pan supports completely, proceed
as shown in Fig. 3.

Model ZGF 692: The hob has two cast iron pan
supports.

Take care when removing them. They are
heavy and could damage the hob or your
kitchen furniture if you let them fall.

Never turn the pan supports on the hinges, this
could damage them.

To remove the pan supports completely, proceed
as shown in Fig. 3.

Wash the pan supports using hot soapy water. If
necessary, a paste cleaner or a soap impregnated steel
wool pad can be used with caution.
After cleaning, be sure to wipe dry with a soft cloth.

The Burners

Fig. 2

Fig. 3

The burner caps and crowns (Fig. 1) can be removed for
cleaning. Wash the burner caps and crowns using hot
soapy water, and remove marks with a mild paste cleaner.
A well moistened soap impregnated steel wool pad can
be used with caution, if the marks are particularly difficult
to remove. After cleaning, be sure to wipe dry with a soft
cloth.

Ignition electrode

The electric ignition is obtained through a ceramic
"electrode" and a metal electrode (Fig. 1 - letter C). Keep
these components very clean, to avoid lighting difficulties,
and check that the burner crown holes are not
obstructed.

5

Something Not Working?

If the hob is not working correctly, please carry out the following checks before contacting your local Service Force
Centre.
IMPORTANT:
a charge will be made even if the appliance is under guarantee.

If you call out an engineer to a fault listed below, or to repair a fault caused by incorrect use or installation,

SYMPTOM

 There is no spark when lighting the gas

 The gas ring burns unevenly

SOLUTION

 Check that the unit is plugged in and the electrical

supply is switched on

 Check that the RCCB has not tripped (if fitted)

 Check the mains fuse has not blown

 Check the burner cap and crown have been

replaced correctly, e.g. after cleaning.

 Check the main jet is not blocked and the burner

crown is clear of food particles.

 Check the burner cap and crown have been

replaced correctly, e.g. after cleaning.

Service and Spare Parts

In the event of your appliance requiring service, or if you
wish to purchase spare parts, please contact your local
Service Force Centre by telephoning:

0870 5 929929

Your telephone call will be automatically routed to the
Service Force Centre covering your post code area.

For the address of your local Service Force Centre and
further information about Service Force, please visit the
website at www.serviceforce.co.uk

Before calling out an engineer, please ensure you have
read the details under the heading “Something Not
Working.”

For Customer Service in the Republic of Ireland please
contact us at the address below:

Zanussi-Electrolux
Electrolux Group (Irl) Ltd
Long Mile Road
Dublin 12
Republic of Ireland

Tel: [phone]
Email: [e-mail]

When you contact the Service Force Centre you will need
to give the following details:

1. Your name, address and post code

2. Your telephone number

3. Clear and concise details of the fault

4. The model and serial number of the appliance (found
on the rating plate)

5. The purchase date

Please note that a valid purchase receipt or
guarantee documentation is required for in­guarantee service calls.

6