Page 1
GAS HOB
ГАЗОВАЯ
ВАРОЧНАЯ
ПОВЕРХНОСТЬ
ZGF 646
INSTRUCTION BOOKLET
РУКОВОДСТВО ПО ЭКСПЛУАТАЦИИ
RU
Page 2
ENGLISH
Important Safety Information
These warnings are provided in the interest of safety. You MUST read them carefully before installing
or using the appliance.
During Operation
• It is most important that this instruction book should
be retained with the appliance for future reference.
Should the appliance be sold or transferred, always
ensure that the book is left with the appliance in order
that the new owner can get to know the functions of
the appliance and the relevant warnings.
• This appliance has been designed for non
professional purpose in private houses only. It is
meant to cook edible foodstuff only and
used for any other purposes.
• It is dangerous to alter the specification in any way.
• For hygiene and safety reasons, this appliance should
be kept clean at all times. A build-up of fats or other
foodstuff could result in a fire.
• Under no circumstances should you attempt to repair
the appliance yourself. Repairs carried out by
unexperienced persons may cause injury or serious
malfunctioning. Refer to your local Zanussi Service
Centre. Always insist on genuine Zanussi spare
parts.
• Ensure that all control knobs are in the OFF position
when not in use.
• Should you connect any electrical tool to a plug near
this cooking appliance, ensure that electric cables
are not in contact with it and keep them far enough
from the heated parts of this appliance.
• If the appliance is out of order, disconnect it from the
electric supply.
MUST NOT be
Child Safety
• Ensure that the gas supply complies with the gas type
stated on the identification label, placed near the gas
supply pipe.
• Using a gas cooking appliance will produce heat
and moisture in the room which it has been
installed in. Ensure a continuous air supply,
keeping the air vents in good conditions or
installing a cooker hood with discharge tube.
• In case of intensive or long time use of the
appliance, make the ventilation more efficient,
by opening a window or increasing the electric
exhaust fan power.
• Once you removed all packaging from the appliance,
ensure that it is not damaged and the electric cable is
in perfect conditions. Otherwise, contact your dealer
before proceeding with the installation.
• The manufacturer disclaims any responsability
should all the safety measures not be carried out.
Service
• Under no circumstances should you attempt to repair
the appliance yourself. Repairs carried out by
unexperienced persons may cause injury or serious
malfunctioning. Refer to your local Service Centre.
Always insist on genuine spare parts.
Environmental Information
• After installation, please dispose of the packaging with
due regard to safety and the environment.
• When disposing of an old appliance, make it unusable,
by cutting off the cable.
• This appliance has been designed to be operated by
adults and children under supervision. Young children
MUST NOT be allowed to tamper with the controls or
play near or with the appliance.
• Accessible parts of this appliance may become hot
when it is in use. Children should be
it has cooled.
•
This appliance is not intended for use by children or
other persons whose physical, sensory or mental
capabilities or lack of experience and knowledge
prevents them from using the appliance safely without
supervision or instruction by a responsible person to
ensure that they can use the appliance safely.
KEPT AWAY until
About Installation, Cleaning
and Manteinance
• It is mandatory that all operations required for the
installation are carried out by a qualified or competent
person, in accordance with existing rules and
regulations.
2
The symbol
indicates that this product may not be treated as household
waste. Instead it shall be handed over to the applicable
collection point for the recycling of electrical and electronic
equipment. By ensuring this product is disposed of
correctly, you will help prevent potential negative
consequences for the environment and human health,
which could otherwise be caused by inappropriate waste
handling of this product. For more detailed information
about recycling of this product, please contact your local
city office, your household waste disposal service or the
shop where you purchased the product.
This appliance complies with the following
E.E.C. Directives:
- 2006/95 (Low Voltage Directive);
- 89/336
- 93/68 (General Directives)
and subsequent modifications.
(Electromagnetical Compatibility Directive);
on the product or on its packaging
Page 3
Contents
Guide to Use the instructions
The following symbols will be found in the text to guide
you throughout the Instructions:
For the User
Important Safety Information 2
Instruction for the User 3
Cleaning and Maintenance 4
""
"
""
Safety Instructions
Step by step instructions for an operation
Hints and Tips
Environmental information
For the Installer
T echnical Dat a 5
Electrical Connection 6
Adaptation to different types of gas 7
Building In 8
Service and original spare parts 1 1
These instructions are only for the countries
stated by the symbol printed on the front cover
of this instruction book.
MANUFACTURER:
ELECTROLUX HOME PRODUCTS ITALY S.p.A.
Viale Bologna 298 - 47100 FORLI’ (Italy)
Instruction for the User
Hob burners control knobs
Using the hob correctly
The hob burners control knobs are situated on the hob
front panel. The symbols on the knobs mean that :
there is no gas supply
•
there is maximum gas supply
there is minimum gas supply
Lighting the burners
For easier lighting, proceed before putting a
pan on the pan support.
Push the relevant knob down and turn it anti-clockwise
until it reaches the "maximum" position.
Mod. ZGF 646 ICTX
After lighting the flame, keep the knob pushed down
for about 5 seconds. This will allow the
"thermocouple" (Fig. 1 lett. D) to be heated and the
safety device to be switched off, otherwise the gas
supply would be interrupted.
Then, check the flame is regular and adjust it as
required.
If you cannot light the flame even after several
attempts, check the "cap" (Fig. 1 lett. A) and the
"crown" (Fig. 1 lett. B) are in the correct position.
To put the flame out, turn the knob to the symbol
• Always turn the flame down or put it out before
taking the pans off the burner.
•
.
To ensure maximum burner efficiency, it is strongly
recommended that you use only pots and pans with a
bottom fitting the size of the burner used, so that flame
will not spread beyond the bottom of the vessel (see the
table beside).
It is also advisable, as soon as a liquid starts boiling, to
turn down the flame so that it will barely keep the liquid
simmering.
Use only pans or pots with flat bottom.
Carefully supervise cookings with fats or oil,
since these types of foodstuff can result in a
fire, if over-heated.
A- Burner cap
B- Burner crown
C- Ignition candle
D- Thermocouple
Fig. 1
Burner minimum maximum
FO 0204
diameter diameter
Big (rapid) 180 mm. 260 mm.
Medium (semirapid) 120 mm. 220 mm.
Small (Auxiliary) 80 mm. 160 mm.
3
Page 4
The Hob Lid (mod. ZGF 646 IX)
In order to make the appliance match with the kitchen
design, a lid (not provided) can be fitted on the hob.
• The lid is meant to avoid dust to settle on the hob,
when it is closed, and to collect splashes of oil or
fat, when it is open. Do not use it for any other
purpose.
• Always wipe off any splash of liquid before
opening the lid.
• Always clean the lid from cooking residues before
opening it or taking it off.
WARNING! The crystal lid can splinter when
overheated. Always ensure all the burners are
off before closing it.
Cleaning and Maintenance
Disconnect the appliance from the electrical
supply, before carrying out any cleaning or
manteinance work.
Wash the enamelled components with warm soapy water.
Never use abrasive cleaners.
Frequently wash the "caps" and the "crowns" with hot
soapy water, carefully taking away any built-up of food.
Carefully wash the stainless steel components with water,
then wipe them dry with a soft cloth.
The pan supports are dishwasher proof.
If the marks are particularly difficult to remove, use
common non-abrasive cleaners or specific products.
Never use steel wool pads or acids.
In models provided with electric ignition, this feature is
obtained through a ceramic "candle" and a metal electrode
(Fig. 1 lett. C). Keep these components well clean, to avoid
difficult lighting, and check that the burner crown holes (lett.
B) are not obstructed.
Pan supports
To keep the pan supports in the right position, they are
hooked to a couple of special hinges in the back of the hob.
Thanks to these hooks, you can lift the pan supports for
easier cleaning, as shown in Fig. 2.
To take the pan supports completely off the hob, proceed
as shown in Fig. 3.
FO 2237
Cast iron pan supports
(ZGF 646 ICTX)
Caution!
When removing the cast iron pan supports, lift
them up as shown in Fig. 3. Nev e r tu rn t h e pa n
supports on the hinges as shown in Fig. 2, since
this could damage them.
Periodic Maintenance
Periodically ask your local Service Centre to check the
conditions of the gas supply pipe and the pressure adjuster,
if fitted.
To ensure the good operation of the hob and its safety
features, it is necessary that the taps are periodically
lubricated.
4
FO 2238
Fig. 2
Fig. 3
Page 5
Technical dat a
Gas Burners Rating
Rapid Burner (big) 3,0 kW (G20) - 2,8 kW (G30-G31)
Semirapid Burner (medium) 2,0 kW
Auxiliary Burner (small) 1,0 kW
Class 3 Appliance
Category II2H3B/P
Setting Natural Gas G20 20 mbar
Gas connection G 1/2"
Electric Supply 230 V
~ 50 Hz
Hob recess dimensions
Length 560 mm.
Width 480 mm.
Instruction for the Installer
The following instructions about installation and
maintenance must be carried out by qualified
personnel in compliance with the regulation in
force.
The appliance must be electrically disconnected
before all interventions. If any electric supply to
the appliance is required to carry out the work,
ensure all the necessary precautions are followed.
Gas Connection
Choose fixed connections or use a flexible pipe in
stainless steel.
If using flexible metallic pipes, be careful they do not
come in contact with mobile parts or they are not
squeezed. Use the same attention when the hob is
combinated with an oven.
The side walls of the unit in which the hob is
going to be installed, must not exceed the height
of the working top.
Avoid installing the appliance in the proximity of
inflammable materials (e.g. curtains, tea towels
etc.).
THE MANUFACTURER WILL NOT ACCEPT LIABILITY,
SHOULD ANY OF THE OTHER SAFETY INSTRUCTIONS
INCORPORATED IN THIS BOOK OR THE REGULATION IN
FORCE BE IGNORED.
A) Ramp with ending nut
B) Seal
C) Adjustable connection
IMPORTANT - To ensure a correct operation, a saving
of energy and the long-life of the appliance, the voltage
pressure of the appliance must correspond to the
recommended values.
The adjustable connection is fixed to the comprehensive
ramp by means of a threaded nut G 1/2".
Interpose the sealing between the components as shown
in Fig. 4.
Screw the parts without forcing, adjust the connection in
the required direction and tighten everything.
IMPORTANT - When the final connection has been
made, it is essential that a thorough leak test is carried
out on the hob and installation. Use some soapy water,
never a flame.
FO 0264
Fig. 4
5
Page 6
Electrical connection
The appliance is designed to be connected to 230 V
monophase electricity supply.
The connection must be carried out in compliance with
the laws and regulations in force.
Before the appliance is connected:
1) check that the main fuse and the domestic installation
can support the load (see the rating label);
2) check that the power supply is properly earthed in
compliance with the current rules;
3) check the socket or the double pole switch used for
the electrical connection can be easily reached with
the appliance built in the forniture unit.
The appliance is supplied with a connection cable. This
has to be provided with a proper plug, able to support the
load marked on the identification plate.
The plug has to be fitted in a proper socket.
If connecting the appliance directly to the electric system,
it is necessary that you install a double pole switch
between the appliance and the electricity supply, with a
minimum gap of 3 mm. between the switch contacts and
of a type suitable for the required load in compliance with
the current rules.
The connection cable has to be placed in order that, in
each part, it cannot reach a temperature 90 °C.
The brown coloured phase cable (fitted in the terminal
block contact marked with "L") must always be connected
to the network phase.
Neutral
Replacement of the voltage cable
The connection of the voltage cable to the appliance's
terminal block is of type "Y". This means that its
replacement requires the specific equipment of a
technician.
In this case, only cable type H05V2V2-F T90 must be
used. The cable section must be suitable to the voltage
and the working temperature.
The yellow/green earth wire must be approximately 2
cm. longer than the phase wires (Fig. 5).
To open the terminal block and reach the terminals,
proceed as follows:
• insert the point of a screwdriver into the visible
protrunding part of the terminal block;
• exert a light pressure and lift (Fig. 6)
FO 0073
FO 0257
Earth (yellow/green)
Fig. 5
Fig. 6
6
Page 7
Adaptation to different types of gas
Injector replacement
• Remove the pan supports.
• Remove the burner's caps and crowns.
• With a socket spanner 7 unscrew and remove the
injectors (Fig. 7), and replace them with the ones
required for the type of gas in use (see table 2).
• Reassemble the parts, following the same procedure backwards.
• Replace the rating label (placed near the gas supply
pipe) with the relevant one for the new type of gas
supply. You can find this label in the package of the
injectors supplied with the appliance.
Should the feeding gas pressure be different or
variable compared with the required pressure, an
appropriate pressure adjuster must be fitted on the gas
supply pipe, in compliance with the rules in force.
Adjustment of minimum level
Fig. 7
FO 0392
To adjust the minimum level of the burners, proceed as
follows:
• Light the burner.
• Turn the knob on the minimum position.
• Remove the knob.
• With a thin screwdriver, adjust the by-pass screw
positioned in the centre of the gas tap control shaft
(see Fig. 6). If changing from natural gas 20 mbar to
liquid gas, completely tighten the adjustment screw
in. If changing from liquid gas to natural gas 20 mbar,
undo the by-pass screw about 1/4 of a turn. If changing
from natural gas 20 mbar to natural gas 13 mbar undo
the by-pass screw about 1/4 of a turn. If changing from
liquid gas to natural gas 13 mbar, undo the by-pass
screw about 3/4 of a turn.
• Finally check the flame does not go out when quickly
turning the knob from the maximum position to the
minimum position.
This procedure can easily be carried out, anyhow the
hob has been positioned or built in the working top.
Table 2 : injectors
Fig. 8
By-pass
screw
Table 1 : BY-pass diameters
Burner Ø By-pass
in 1/100
of mm.
Auxiliary 28
Semi-rapid 32
Rapid 40
BURNER NORMAL REDUCED NORMAL
POWER POWER POWER
kW kW NATURAL GAS LPG
G20 - 20 mbar G30/30 mbar
3
inj. 1/100 m
Auxiliary (small) 1,0 0,33 70* 0,095 50 73
Semi-rapid (medium) 2,0 0,45 96* 0,190 71 145
Natural gas :
Rapid (big) 3,0 0,65 119* 0,286 86 204
LPG : 2,8
/h inj. 1/100 g/h - G30
7
Page 8
Building in
SR
A
R
SR
A
SR
R
SR
580
Fig. 9
510
ZGF 646 IX
A = Auxiliary burner
SR = Semirapid burner
R = Rapid Burner
These hobs can be inserted in a built-in kitchen unit
whose depth is between 550 and 600 mm. The hobs
dimensions are shown in Fig. 9.
Fitting the lid (only mod. ZGF 646 IX)
We recommend the lid hinge block are fitted
before installing the hob into the worktop.
To install the lid onto the hob, proceed as follows:
a. Remove the right and left hand grid blocks fitted to the
back of the hob, by unscrewing the relevant screws
(Fig. 10)
b. Fit the lid hinge blocks onto the hob, using the original
screws, ensuring that the relevant shims are fitted
between the hinge blocks and the hob (Fig. 10);
c. Fit the left hand lid hinge (marked S) into the hinge
block (Fig.11);
d. Carry out the same operation with the right hand lid
hinge (marked D).
580
ZGF 646 ITCX
FO 2035
510
Fig. 10
Adjusting the lid balance
To adjust the lid balance, turn clockwise or anticlockwise the central screw of the right- and left-hand
hinges (Fig. 12).
8
FO 2036
Fig. 11
FO 2037
Fig. 12
Page 9
Installation and assembly
These hobs can be installed in a kitchen unit with an
opening for insertion whose dimensions are shown in
Fig. 13.
The edge of the cut out must have a minimum distance
from the rear wall of 55 mm.
If there are side walls, or sides of the furniture unit near
the hob, the cut out edges must have a minimum
distance of 100 mm. as shown in Fig. 13.
Carry out the building in of the hob as follows:
• put the relevant sealings, supplied with the hob, on
the edges of the cut out, as shown in Fig. 14, taking
care that the sealings meet without overlapping;
• place the hob in the cut out, taking care of its centring;
• fix the hob with the relevant screws (Fig. 15). The
traction of the screws is able to trace the sealing, any
excess of which can then be easily removed.
The edge of the hob forms a double labyrinth seal
which provides a total guarantee against infiltration of
liquids.
100
FO 2038
Fig. 13
Fig. 14
FO 0199
a) sealing
a
Fig. 15
9
Page 10
Possibilities for
insertion
Kitchen unit with door
Proper arrangements must be
taken in designing the forniture
unit, in order to avoid any contact
with the bottom of the hob which
can be heated when it is operated.
The recommended solution is
shown in Fig. 16.
The panel fitted under the hob
should be easily removable to
allow an easy access if a technical
assistance intervention is needed.
Fig. 16 Fig. 17
480
30
593
380
140
Kitchen unit with oven
The hob recess dimensions must
comply the indication given in Figs.
17 and 20 and must be provided
with brackets to allow a
continuous supply of air.
To avoid overhating, the building
in should be carried out as shown
in Figs. 18 e 19.
The hob's electric connection and
the oven's one must be carried out
separately, both for safety reasons
and to allow the oven to be easily
taken off the unit.
Hanging forniture units or hoods
must be placed at 650 mm.
minimum from the hob (Fig. 21).
FO 2044 FO 2043
a) Removable panel
b) Space possibly useful for
connections
Fig. 18
Fig. 19
Fig. 20
FO 0198
10
FO 2041
FO 2042
Fig. 21
FO 2240
Page 11
Service and original spare p art s
This machine, before leaving the factory, has been
tested and studied by many experts and specialists, in
order to give you the best results.
Any repair work which needs to be carried out should be
done with the utmost care and attention.
For this reason we recommend that for any problem you
contact the dealer who sold it to you, or our nearest
authorized Service Centre, specifying the nature of the
problem, the appliance model (Mod.), the product
number (Prod. No.) and the serial number (Ser. No.)
marked on the identification plate.
Original spareparts, certified by the product
manufacturer and carrying this symbol are only available
at our Service Centre and authorized spareparts shops.
11
Page 12
12
Loading...