Zanussi ZGF 646 CTNC User Manual
User
Manual
Pуководство
по
эксплуатации
ZGF 646 CT
ZGF 646 IT
Gas
Hob
Газовая
варочная
поверхность
ZGF 648 IR
ZGF 648 IX
ZGF 643 ITXC
RU
2
Thank you for selecting our applianceThank you for selecting our appliance
Thank you for selecting our appliance
Thank you for selecting our applianceThank you for selecting our appliance
We wish you lots of enjoyment with your new appliance and we hope that
you will consider our brand again when purchasing household appliances.
Please read this user manual carefully and keep it throughout the product
life cycle as a reference document. The user manual should be passed on
to any future owner of the appliance.
3
Contents
For the User
Important safety information .............................................................................. 5
Operation .......................................................................................................... 7
Using the hob correctly ..................................................................................... 8
Cleaning and Maintenance ................................................................................ 9
Service and original spare parts ....................................................................... 21
European guarantee ........................................................................................ 21
For the Installer
Technical data ................................................................................................. 11
Installation ....................................................................................................... 13
Adaptation to different types of gas ................................................................. 15
Electrical connection ....................................................................................... 16
Building in ....................................................................................................... 17
Possibilities for insertion .................................................................................. 20
Guide to Use the instructions
The following symbols will be found in the text to guide you throughout the
Instructions:
Safety Instructions
Step by step instructions for an operation
)
Hints and Tips
Environmental information
This appliance complies with the following E.E.C. Directives:
• 2006/95 (Low Voltage Directive);
• 89/336 (Electromagnetical Compatibility Directive);
• 90/396 (Gas Appliances);
• 93/68 (General Directives)
and subsequent modifications.
MANUFACTURER:MANUFACTURER:
MANUFACTURER:
MANUFACTURER:MANUFACTURER:
ELECTROLUX HOME PRODUCTS ITALY S.p.A.
Viale Bologna, 298
47100 FORLÌ (Italy)
4
English
Important safety information
This warnings has been given for the safety of you and others. We therefore
ask you to carefully read the procedures of installing and using this appliance.
Installation
z The work of installation must be
carried out by competent and qualified
installers according to the regulations
in force.
• Any modifications to the domestic
electrical mains which may be
necessary for the installation of the
appliance should be carried out only
by competent personnel.
During Operation
• This appliance has been designed for
non professional purpose in private
houses only. It is meant to cook edible
foodstuff only and must not be used
for any other purposes.
• It is dangerous to alter the specification
in any way.
• For hygiene and safety reasons, this
appliance should be kept clean at all
times. A build-up of fats or other
foodstuff could result in a fire.
• Under no circumstances should you
attempt to repair the appliance
yourself. Repairs carried out by
unexperienced persons may cause
injury or serious malfunctioning. Refer
to your local Service Centre. Always
insist on genuine spare parts.
• Ensure that all control knobs are in the
OFF position when not in use.
• Should you connect any electrical tool
to a plug near this cooking appliance,
ensure that electric cables are not in
contact with it and keep them far
enough from the heated parts of this
appliance.
• If the appliance is out of order,
disconnect it from the electric supply.
People Safety
• This appliance has been designed to
be operated by adults and children
under supervision. Young children
must not be allowed to tamper with the
controls or play near or with the oven.
• This appliance is not intended for use
by children or other persons whose
physical, sensory or mental capabilities
or lack of experience and knowledge
prevents them from using the
appliance safely without supervision or
instruction by a responsible person to
ensure that they can use the appliance
safely.
• Accessible parts of this appliance may
become hot when it is in use. Children
should be kept away until it has
cooled.
About Installation, Cleaning and
Manteinance
z It is mandatory that all operations
required for the installation are carried
out by a qualified or competent
person, in accordance with existing
rules and regulations.
• Disconnect the appliance from the
electrical supply, before carrying out
any cleaning or manteinance work.
• Ensure a good ventilation around the
5
appliance. A poor air supply could
cause lack of oxygen.
• Ensure that the gas supply complies
with the gas type stated on the
identification label, placed near the gas
supply pipe.
• This appliance is not connected to a
combustion products evacuation
device. It must be installed and
connected in accordance with current
installation regulations. Particular
attention shall be given to the relevant
requirements regarding ventilation.
• The use of a gas cooking
appliance results in the production
of heat and moisture in the room in
which it is installed. Ensure that
the kitchen is well ventilated: keep
natural ventilation holes open or
install a mechanical ventilation
device (mechanical extractor
hood).
• Prolonged intensive use of the
appliance may call for additional
ventilation, for example opening of
a window, or more effective
ventilation, for example increasing
the level of mechanical ventilation
where present.
• Once you removed all packaging from
the appliance, ensure that it is not
damaged and the electric cable is in
perfect conditions. Otherwise, contact
your dealer before proceeding with the
installation.
• The manufacturer disclaims any
responsability should all the safety
measures not be carried out.
Service
• Under no circumstances should you
attempt to repair the appliance
yourself. Repairs carried out by
unexperienced persons may cause
injury or serious malfunctioning. Refer
to your local Service Centre. Always
insist on genuine spare parts.
Environmental Information
z After installation, please dispose of
the packaging with due regard to
safety and the environment.
• When disposing of an old appliance,
make it unusable, by cutting off the
cable.
The symbol on the product or
on its packaging indicates that this
product may not be treated as household
waste. Instead it shall be handed over to
the applicable collection point for the
recycling of electrical and electronic
equipment. By ensuring this product is
disposed of correctly, you will help
prevent potential negative consequences
for the environment and human health,
which could otherwise be caused by
inappropriate waste handling of this
product. For more detailed information
about recycling of this product, please
contact your local city office, your
household waste disposal service or the
shop where you purchased the product.
It is very important that this
instruction book should be kept
safely for future consultation. If the
appliance should be sold or given to
another person, please ensure that
the booklet goes together with it, so
that the new owner can know of the
functions of the machine and also be
aware of the warnings.
These instructions are only for the
countries stated by the symbol printed
on the front cover of this instruction
book.
6
Operation
Hob burner control knobs
The symbols on the knobs mean:
z = no gas supply
= maximum gas supply
= minimum gas supply
For easier lighting, proceed before
putting a pan on the pan support.
Lighting the burners
)
Push the relevant knob down and
turn it anti-clockwise until it reaches
the "maximum" position.
Only for mod. ZGF 646 CT / ZGF
646 IT / ZGF 648 IR / ZGF 643 ITXC
After lighting the flame, keep the
knob pushed down for about 5
seconds. This will allow the
"thermocouple" (see figure - lett. D) to be
heated and the safety device to be
switched off, otherwise the gas supply
would be interrupted.
Then, check the flame is regular and
adjust it as required.
If you cannot light the flame even after
several attempts, check the "cap" and
“crown” (see figure - lett. A, B) are in the
correct position.
When switching on the mains, after
installation or a power cut, it is quite
normal for the spark generator to be
activated automatically.
In the absence of electricity, ignition can occur without the
electrical device; in this case
approach the burner with a flame,
push the relevant knob down and
turn it anti-clockwise until it
reaches the "maximum" position.
A - Burner cap
B - Burner crown
C - Ignition candle
D - Thermocouple
7
Do not keep the control knob
pressed for more than 15 seconds.
If the burner does not light
even after 15 seconds, release
the control knob, turn it the
"off" position and wait for at
least one minute before trying
to light the burner again.
To switch off burners
)
To put the flame out, turn the knob to
the symbol (z).
The Hob Lid (available only for
model ZGF 646 IT, ZGF 648 IX)
In order to make the appliance match
with the kitchen design, a lid (not supplied)
can be fitted on the hob.
• The lid is meant to avoid dust to
settle on the hob, when it is closed,
and to collect splashes of oil or
fat, when it is open. Do not use it
for any other purpose.
Using the hob correctly
Practical hints
The burners
To ensure maximum burner
efficiency, you should only use pots and
pans with a flat bottom fitting the size of
the burner used.
Rapid Burner diameter 16-26 cm
Semi-rapid Burner diameter 12-22 cm
Auxiliary Burner diameter 8-16 cm
• For easier lighting, proceed before
putting a pan on the pan support.
• Use only pans or pots with flat bottom.
• Always wipe off any splash of
liquid before opening the lid.
• Always clean the lid from cooking
residues before opening it or
taking it off.
WARNING! The
crystal lid can
splinter when
overheated.
Always ensure
all the burners
are off before
closing it.
8
• Take care when frying food in hot
oil or fat, as the overheated
splashes could easily ignite.
• If you use a saucepan which is smaller
than the recommended size, the flame
will spread beyond the bottom of the
vessel, causing the handle to overheat.
• Pots must not enter the control zone.
• If the control knobs become difficult to
turn, please contact your local Service
Force Centre.
• As soon as a liquid starts boiling, turn
down the flame so that it will barely
keep the liquid simmering.
• Prolonged cooking with
potstones, earthenware pans or
cast-iron plates is inadvisable.
Also, do not use aluminium foil to
protect the top during use.
• Make sure pots do not protrude over
the edges of the cooktop and that they
are centrally positioned on the rings in
order to obtain lower gas
consumption.
• Do not place unstable or deformed
pots on the rings: they could tip over or
spill their contents, causing accidents.
Cleaning and Mainteinance
Disconnect the appliance from
the electrical supply, before
carrying out any cleaning or
manteinance work.
The hob is best cleaned whilst
it is still warm, as spillage can
be removed more easily than if
it is left to cool.
This appliance cannot be
cleaned with steam or with a
steam cleaning machine.
The burners
z The burner caps and crowns can be
removed for cleaning.
z Wash the burners taps and crowns
using hot soapy water, and remove
marks with a mild paste cleaner. A
well moistened soap impregnated
steel wool pad can be used with
caution, if the marks are particularly
difficult to remove.
z After cleaning, be sure to wipe dry
with a soft cloth.
z Frequently wash the "caps" and the
"crowns" with hot soapy water,
carefully taking away any built-up of
food.
The Hob Top
z Regularly wipe over the hob top
using a soft cloth well wrung out in
warm water to which a little wasing
up liquid has been added. Avoid the
use of the following:
- household detergent and bleaches;
- impregnated pads unsuitable for
non-stick saucepans;
- steel wool pads;
- bath/sink stain removers.
z Should the hob top become heavily
soiled, the following products are
recommended:
- For stainless steel hobs use a
9
proprietary stainless steel cleaner.
- For other hobs use Hob Brite or Bar
Keepers Friend.
z Do not leave acid or alkaline
substances (e.g. vinegar, salt,
lemon juice, etc.) on the cooktop.
Pan supports
To keep the pan supports in the right
position, they are hooked to a couple of
special hinges in the back of the hob.
Thanks to these hooks, you can lift the pan
supports for easier cleaning, as shown in
the picture.
To take the pan supports completely off the
hob, proceed as shown in the picture.
Wash the pan supports using hot soapy
water. If necessary, a paste cleaner or a
soap impregnated steel wool pad can
be used with caution.
After cleaning, be sure to wipe dry with
a soft cloth.
The Ignition electrode
The electric ignition is obtained
through a ceramic electrode with a
metal electrode. Keep these
components very clean, to avoid difficult
lighting, and check that the burner
crown holes are not obstructed.
NO
Cast iron pan supports
(ZGF
643 ITXC / ZGF 646 CT / ZGF
648 IR)
Caution!
When removing the cast iron pan
supports, lift them up. Never turn
the pan supports on the hinges
since this could damage them.
Periodic Maintenance
Periodically ask your local Service Centre
to check the conditions of the gas supply
pipe and the pressure adjuster, if fitted.
10
YES
Technical data
Burner gas power (natural gas G20-20 mbar)
Rapid burner 3,0 kW
Semi-rapid burner 2,0 kW
Auxiliary burner 1,0 kW
Category II2H3B/P
Gas supply natural gas G20 (2H) / 20 mbar
Gas connection G 1/2"
Electric supply 230 V~ 50 Hz
Appliance class 3
Hob dimensions
Width 580 mm
Depth 510 mm
Cut out dimensions
Width 560 mm
Depth 480 mm
By-pass diameters
Burner Ø By-pass in 1/100 mm.
Auxiliary 28
Semi-rapid 32
Rapid 42
11
Gas burners
NORMAL REDUCED
POWER POWER
BURNER NATURAL GAS LPG
G20 (2H) - 20 mbar
kW kW g/h
inj. m3/h inj.
100/mm 100/mm
Auxiliary
burner 1,0 0,33 70 0,095 50 73 71
Semi-rapid
burner 2,0 0,45 96 0,190 71 145 143
Rapid 3,0
burner (natural gas) 0,75 119 0,285 86 204 200
2,8
(
LPG
)
NORMAL
POWER
(Butane/Propane) 30 mbar
G30 G31
Gas burners G20 13 mbar - only for Russia
NORMAL REDUCED
POWER POWER
BURNER
kW kW inj. m3/h
Auxiliary
burner 0,9 0,33 80 0,095
Semi-rapid
burner 1,4 0,45 105 0,148
Rapid
burner 1,9 0,75 120 0,20
NORMAL
POWER
NATURAL GAS
G20 - 13 mbar
100/mm
12
Installation
l The following instructions about
installation and maintenance must
be carried out by qualified
personnel in compliance with the
regulation in force.
l The appliance must be electrically
disconnected before all
interventions. If any electric supply
to the appliance is required to
carry out the work, ensure all the
necessary precautions are
followed.
l The side walls of the unit in which
the hob is going to be installed,
must not exceed the height of the
working top.
l Avoid installing the appliance in
the proximity of inflammable
materials (e.g. curtains, tea towels
etc.).
THE MANUFACTURER WILL NOT
ACCEPT LIABILITY, SHOULD ANY
OF THE OTHER SAFETY
INSTRUCTIONS INCORPORATED IN
THIS BOOKLET OR THE
REGULATION IN FORCE BE
IGNORED.
Gas connection
Choose fixed connections or use a
flexible pipe in stainless steel in
compliance with the regulation in force.
If using flexible metallic pipes, be careful
they do not come in contact with mobile parts or they are not squeezed. Use
the same attention when the hob is
combinated with an oven.
13
IMPORTANT - To ensure a correct
operation, a savingof energy and the
long life of the appliance, the voltage
pressure of the appliance must
correspond to the recommended values.
The adjustable connection is fixed to the
comprehensive ramp by means of a
threaded nut G 1/2". Interpose the
sealing between the components as
shown in the picture. Screw the parts
without forcing, adjust the connection in
the required direction and tighten
everything.
IMPORTANT
Once installation is complete,
check the perfect seal of every
pipe fitting, using a soapy
solution, never a flame.
A) Ramp with ending nut
B) Seal
C) Adjustable connection
14
Loading...