Zanussi ZGF642X, ZGF642W, ZGF642B User Manual

GAS HOB
MODEL ZGF 642
INSTRUCTION BOOKLET
2
Please read this instruction booklet before using the appliance
Important Safety Information
Installation
You MUST read hese warnings carefully before installing or using the hob. If you need assistance, contact our Customer Care Department on 01635 521313
This hob must be installed by qualified personnel,
according to the manufacturer’s instructions and to the relevant British Standards.
Any gas installation must be carried out by a
registered CORGI installer.
Remove all packaging before using the hob.
Ensure that the gas and electrical supply complies
with the type stated on the rating plate, located near the gas supply pipe.
Do not attempt to modify the hob in any way.
Child Safety
This hob is designed to be operated by adults. Do
not allow children to play near or with the hob.
The hob gets hot when it is in use.
Children should be kept away until it has cooled.
Children can also injure themselves by pulling pans
or pots off the hob.
When using other electrical appliances, ensure the
cable does not come into contact with the hot surfaces of the cooking appliance.
Unstable or misshapen pans should not be used on
the hob as unstable pans can cause an accident by tipping or spillage.
Never leave the hob unattended when cooking with
oil and fats.
Never use plastic or aluminium foil dishes on the
hob.
Perishable food, plastic items and areosols may be
affected by heat and should not be stored above or below the hob unit.
Service
This hob should only be repaired or serviced by an
authorised Service Engineer and only genuine approved spare parts should be used.
During Use
This hob is intended for domestic cooking only. It is
not designed for commercial or industrial purposes.
When in use a gas cooking appliance will produce
heat and moisture in the room in which it has been installed. Ensure there is a continuous air supply, keeping air vents in good condition or installing a cooker hood with a venting hose.
When using the hob for a long period time, the
ventilation should be improved, by opening a window or increasing the extractor speed.
Do not use this hob if it is in contact with water.
Do not operate the hob with wet hands.
Ensure the control knobs are in the ‘OFF’ position
when not in use.
Environmental Information
After installation, please dispose of the packaging
with due regard to safety and the environment.
When disposing of an old appliance, make it
unusable, by cutting off the cable.
Keep this instruction book for future
reference and ensure it is passed on
to any new owner.
3
Contents
For the User
Description of the Hob Page 5
Operation Page 6 Maintenance
and Cleaning Page 7 Something
Not Working Page 8 Service and
Spare Parts Page 8 Peace of Mind
for 24 Months Page 9
For the Installer
Technical Data Page 10 Important Safety
Requirements Page 11 Installation Page 12 Gas Connection Page 12 Building In Page 13 Electrical Connection Page 14 Wiring Diagram Page 15 Fault Finding Page 16 Commissioning Page 18 Servicing Page 19 Conversion from
natural gas to LPG Page 19
Guide to Use the instructions
The following symbols will be found in the text to guide you throughout the Instructions:
Safety Instructions
Step by step instructions for an operation
This appliance complies with the following
E.E.C. Directives: * 73/23 - 90/683
(Low VoltageDirective);
* 93/68 (General Directives); * 89/336 (Electromagnetical Compatibility Directive); * 90/396 (Gas Appliances),
and subsequent modifications
Hints and Tips
i
4
Description of the Hob
2 3
1
5
6
7
8
1. Hob Top
2. Auxiliary Burner
3. Semi-rapid Burners
4. Rapid Burner
5. Control knob for front left burner (auxiliary)
6. Control knob for back left buner (semi-rapid)
7. Control knob for back right burner (semi-rapid)
8. Control knob for front right burner (rapid)
3
4
INSTALLATION
Any gas installation must be carried out by a registered CORGI installer, and in accordance with existing rules and
regulations. The relevant instructions are to be found in the second section of this manual.
Please, ensure that, once the hob is
installed, it is easily accessible for the
engineer in the event of a breakdown.
WHEN THE HOB IS FIRST INSTALLED
Once the hob has been installed, it is important to remove any protective materials, which were put on in the factory.
5
Operation
HOB BURNERS
To light a burner, turn the relevant knob anticlockwise to maximum position and push down the knob to ignite. If the burner does not ignite, turn the control knob to zero, and try again.
When switching on the mains, after installation or a power cut, it is quite normal
i
for the spark generator to be activated automatically.
To ensure maximum burner efficiency, you should only use pots and pans with a flat bottom fitting the size of the burner used (see table).
Burner minimum maximum
diameter diameter
Large (rapid) 160 mm. 240 mm. Medium (semi-rapid) 120 mm. 220 mm. Small (Auxiliary) 80 mm. 160 mm.
If you use a saucepan which is smaller than the recommended size, the flame will spread beyond the bottom of the vessel, causing the handle to overheat.
As soon as a liquid starts boiling, turn down the flame so that it will barely keep the
i
liquid simmering.
Take care when frying food in hot oil or fat, as the overheated splashes could easily ignite.
If the control knobs become difficult to turn, please contact your local Electrolux Service Centre.
6
Maintenance and Cleaning
Before any maintenance or cleaning can be
carried out, you must DISCONNECT the
hob from the electricity supply.
The hob is best cleaned whilst it is still warm, as spillage can be removed more easily than if it is left to cool.
The Hob Top
Regularly wipe over the hob top using a soft cloth well wrung out in warm water to which a little wasing up liquid has been added. Avoid the use of the following:
- household detergent and bleaches;
- impregnated pads unsuitable for non-stick saucepans;
- steel wool pads;
- bath/sink stain removers. Should the hob top become heavily soiled, it is
recommended that a cleaning product such as Hob Brite or Bar Keepers Friend is used.
Pan Supports
The hob has two cast iron pan supports. Take care when removing them. They are fair heavy and could damage the hob or your kitchen furniture if you let them fall down.
To keep the pan supports in the correct position, they are hooked into hinges at the back of the hob. When removing the pan supports, lift them up as shown in the diagram. Never turn the pan supports on the hinges, this could damage them. Wash the pan supports using hot soapy water. If necessary, a paste cleaner or a soap impregnated steel wool pad can be used with caution.
The Burners
The burner caps and crowns can be removed for cleaning.
YES
NO
Wash the burners taps and crowns using hot soapy water, and remove marks with a mild paste cleaner. A well moistened soap impregnated steel wool pad can be used with caution, if the marks are particularly difficult to remove.
After cleaning, be sure to wipe dry with a soft cloth.
7
Loading...
+ 13 hidden pages