POWER SUPPLY VOLTAGE AND FREQUENCY
TOTAL POWER ABSORBED
FREEZING CAPACITY
AVERAGE DAILY UNITS ELECTRICITY*
GROSS CAPACITY
NET CAPACITY
Height
Width
Depth
Fridge
Freezer
Superchill comp.
Fridge
Freezer
Superchill comp.
170cm
59.5 cm
60cm
220-240 V / 50 Hz
180 W
11 kg / 24 h
2.10 kWh
154 l
83 l
45 l
150 l
62 l
29 l
STAR RATING
* This figure is based on standard test results in accordance with European Standard EN153. Actual
consumption will depend on how the appliance is used and where it is located.
2
“
“
“
“
“
“
“
“
“
“
“
“
“
“
“
“
“
“
WARNINGS
IT IS MOST IMPORTANT THAT THIS INSTRUCTION
BOOK SHOULD BE RETAINED WITH THE APPLIANCE
FOR FUTURE REFERENCE. SHOULD THE APPLIANCE
BE SOLD OR TRANSFERRED TO ANOTHER OWNER, OR
SHOULD YOU MOVE HOUSE AND LEAVE THE
APPLIANCE, ALWAYS ENSURE THAT THE BOOK IS
SUPPLIED WITH THE APPLIANCE IN ORDER THAT
THE NEW OWNER CAN GET TO KNOW THE
FUNCTIONING OF THE APPLIANCE AND THE
RELEVANT WARNINGS.
THESE WARNINGS ARE PROVIDED IN THE INTEREST
OF SAFETY. YOU MUST READ THEM CAREFULLY
BEFORE INSTALLING OR USING THE APPLIANCE.
This appliance is designed to be operated by
adults. Children should not be allowed to tamper
with the controls or play with the product.
Any electrical work required to install this
appliance should be carried out by a qualified
electrician or competent person.
This product should be serviced by an authorised
ZANUSSI Service Centre, and only genuine
spare parts should be used.
It is dangerous to alter the specifications or
modify this product in any way.
Care must be taken to ensure that the appliance
does not stand on the electrical supply cable.
ZANUSSI domestic refrigerators, freezers and
fridge/freezers are designed to be used
specifically for the storage of edible foodstuffs
only.
The cooling plate or refrigerated freezer shelves
in this appliance contain channels through which
the refrigerant passes. If these are punctured
this would cause substantial damage to the
appliance and result in food loss. DO NOT USE
SHARP INSTRUMENTS to scrape off frost or
ice. Under NO circumstances should solid ice be
forced off the lining or shelves. Solid ice should be
allowed to thaw, when defrosting the appliance.
See Defrost instructions.
The appliance should be left for 2 hours after
installation before it is turned on in order to allow
the refrigerant to settle.
This appliance is heavy. Care should be taken
when moving it.
Do not remove items from the freezer if your
hands are damp/wet, as this could cause skin
abrasions or “frost/freezer burns”.
Ice lollies can cause “frost/freezer burns” if
consumed straight from the freezer.
Manufacturers’ storage recommendations should
be strictly adhered to. Refer to relevant
instructions.
Under no circumstances should you attempt to
repair the appliance yourself. Repairs carried out
by inexperienced persons may cause injury or
serious malfunctioning. Refer to your local
ZANUSSI Service Centre and always insist on
genuine spare parts.
There are working parts in this product which
heat up. Always ensure that there is adequate
ventilation as a failure to do this will result in
possible food loss. See installation instructions.
Parts which heat up should not be exposed.
Wherever possible, the back of the appliance
should be close to a wall but leaving the required
distance for ventilation as stated in the
installation instructions.
Before defrosting, cleaning or maintenance work
is carried out, be sure to switch off the appliance
and unplug it.
Frozen food must NOT be re-frozen once it has
thawed out.
Do not place carbonated or fizzy drinks in the
freezer as it creates pressure on the container,
which may cause it to explode, resulting in
damage to the appliance.
08/96
2222 159-45
3
CONSERVATION
In the interests of the Environment:
When disposing of your old fridge, freezer or fridge/
freezer.
Help to keep your country tidy – use authorised
disposal sites for your old appliances.
For maximum efficiency:
Make sure that the appliance is cleaned properly.
Make sure that the door is closed properly.
Do not position the appliance near to sources of
heat.
Do not over-fill your appliance, air MUST be
allowed to circulate.
4
INSTALLATION
Positioning
This appliance is designed to operate in ambient
temperatures between 10
It should be located in a dry atmosphere, out of
direct sunlight and away from extreme
temperature e.g. not next to a cooker or other
sources of direct heat, or in a very cold room e.g. an
outhouse, where the temperatures may fall below
°C (50 °F). If these temperatures are exceeded i.e.
10
colder or warmer, then the appliance may not
operate correctly.
5 cm
°C (50 °F) and 32 °C (90 °F).
Fig. 1
Levelling
The appliance is provided with two levelling feet
located at the front, and two rear castors for easy
movement.
The refrigerator should be carefully levelled,
adjusting the feet as shown in Fig. 2.
Fig. 2
3P 03
Before using
3P02
Before switching the appliance on, wash the inside
of the appliance with lukewarm water and a little
bicarbonate of soda (5ml to 0.5 litre of water).
5
DOOR REVERSAL
The appliance is normally supplied with doors which
open from left to right. To change the opening
direction, proceed as follows:
Bottom door:
1. Unclip and remove the ventilation grille (A).
2. Unscrew and remove the lower hinge (B) and
slide the lower door from its top hinge.
3. Unscrew the pin (C) from the hinge and refit it
onto the hinge on the opposite side.
4. Refit the lower door onto pin (C) and reassemble
the lower hinge (B) on the opposite side.
5. Break off the plug (D) from the ventilation grille.
You may need a pair of pliers for this.
6. Fit the plug (E) (supplied with the appliance) into
the slot left open on the other side.
7. Refit the ventilation grille (A) clipping it into
position.
Fig. 3
Top door:
1. Unscrew the hinge (G) and remove the upper
door.
2. Unscrew the pin (I) from hinge (G) and refit the
pin into the same hole, but on the opposite side of
the hinge.
3. Unscrew the pin (L) from the upper hinge and
refit it in the hinge on the opposite side.
4. Fit the upper door onto the pin (L); refit hinge (G)
on the opposite side.
Adjusting the alignment of the upper door
If, after having changed the opening direction, the
door is not properly aligned, the upper hinge can be
adjusted. To do this, slacken the pin (L) (using a 12
mm spanner) and the self-tapping screw located
under the hinge (using a Phillips screwdriver); align
the door, then retighten the screw and the pin.
C
L
L
G
I
I
G
C
B
B
6
E
A
D
3P 06
Loading...
+ 12 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.