How it Works
Zanussi
Loading...
ZDI111N
User Manual
28 pgs1.73 Mb0
User Manual [nl]
32 pgs1.72 Mb0
User Manual [cz]
24 pgs805.29 Kb0
User Manual [de]
32 pgs1.75 Mb0
User Manual [pt]
28 pgs1.72 Mb0

Zanussi ZDI111N, ZDI111W User Manual

User
manual
Dishwasher
ZDI 111
156997390en.qxp 1/17/2007 3:17 PM Page 1
2
Content
156997390en.qxp 1/17/2007 3:17 PM Page 2
Correct use
● This dishwasher is only intended for washing
household utensils suitable for machine washing.
● Do not put any solvents in the dishwasher.
This could cause an explosion.
● Knives and other items with sharp points
must be loaded in the cutlery basket with their points down or placed in a horizontal position in the upper basket.
● Only use products (detergent, salt and rinse
aid) suitable for dishwashers.
● Avoid opening the door whilst the appliance
is in operation, hot steam may escape.
● Do not take any dishes out of the dishwasher
before the end of the dishwashing cycle.
● After use, isolate the appliance from the
power supply and turn off the water supply.
● This product should be serviced only by an
authorised service engineer, and only genuine spare parts should be used.
General safety
● Dishwasher detergents can cause chemical
burns to eyes, mouth and throat. Could endanger life! Comply with the safety instructions of the dishwasher detergent manufacturer.
● The water in your dishwasher is not for
drinking. Detergent residues may still be present in your machine.
● Ensure that the door of the dishwasher is
always closed when it is not being loaded or unloaded. In this way you will avoid anybody tripping over the open door and hurting themselves.
● Do not sit or stand on the open door.
Child safety
● This appliance is designed to be operated by
adults. Don’t allow children to use the dishwasher unsupervised.
● Keep all packaging well away from children.
There is risk of suffocation.
● Keep all detergents in a safe place out of
children’s reach.
● Keep children well away from the dishwasher
when the door is open.
Installation
● Check your dishwasher for any transport
damage. Never connect a damaged machine. If your dishwasher is damaged contact your supplier.
● All packaging must be removed before use.
● Any electrical and plumbing work required to
install this appliance must be carried out by a qualified and competent person.
● For safety reasons it is dangerous to alter
the specifications or attempt to modify this product in any way.
3
Safety information
In the interest of your safety and to ensure the correct use, before installing and first using the appliance, read this user manual carefully, including its hints and warnings. To avoid unnecessary mistakes and accidents. it is important to ensure that all people using the appliance are thoroughly familiar with its operation and safety features. Save these instructions and make sure that they remain with the appliance if it is moved or sold, so that everyone using it through its life will be properly informed on appliance use and safety.
156997390en.qxp 1/17/2007 3:17 PM Page 3
Control panel and functions
● Never use the dishwasher if the electrical
supply cable and water hoses are damaged; or if the control panel, work top or plinth area are damaged such that the inside of the appliance is freely accessible. Contact your local Service Force centre, in order to avoid hazard.
4
● All sides of the dishwasher must never be
drilled to prevent damage to hydraulic and electric components.
WARNING!
For electrical and water connection carefully follow the instructions given in specific paragraphs.
1. Programme selector dial and On/Off switch
2. Start/cancel button
3. Delay start button
4. Indicator lights
5. On/off indicator light
Programme selector dial and On/Off switch
● when in this position, the machine is switched off (On/Off
indicator light off),
● when the marker on the dial corresponds with a programme,
the machine is switched on and a programme is selected (On/off indicator light on).
156997390en.qxp 1/17/2007 3:17 PM Page 4
5
WASH
Indicator lights
END
Illuminates when the washing and rinsing phases are running.
Illuminates when a washing programme has ended. Switch of the dishwasher by returning the programme selector dial to the Off position. The On/Off indicator light turns off.
It also has added functions of visual signalling as:
- the setting of the water softener,
- intervention of an alarm due to the malfunction of the machine.
DRY
Illuminates when the drying phase is running.
SALT
Illuminates when the special salt has run out. It can remain illuminated several hours after the salt has been filled.
Delay start button
This option allows the start of the programme to be delayed by 3 hours. Once the washing programme has been set, press the delay start button.
The corresponding indicator light illuminates. Press the Start/Cancel button, the countdown of the delay start begins
automatically. Once the countdown has elapsed the washing programme will start
automatically. The delay start indicator light turns off.
Cancel the delay start in progress:
press and hold the Start/Cancel button until the Start/Cancel and delay start indicator lights turn off. To start the washing programme press the Start/Cancel button.
Start/Cancel button
● Starting the washing programme:
1. Select a washing programme.
2. Press the Start/Cancel button (On/Off indicator light on).
IMPORTANT!
Once the programme has started, if you want to change the selection made you must cancel the washing programme in progress.
● Cancel the washing programme in progress:
1. Press and hold the Start/Cancel button until the corresponding light turns off.
2. Release the Start/Cancel button.
3. Turn the programme selector dial to the Off position or select a new washing programme (check that there is detergent in the detergent dispenser).
156997390en.qxp 1/17/2007 3:17 PM Page 5
Programme Use Cycle description
6
Programme table
INTENSIVE 70°C Heavy soil. Prewash - Main wash
Crockery, cutlery, 2 intermediate rinses ­pots and pans Final rinse - Dry
RINSE & HOLD Any. Prewash
Partial load (to be completed later in the day). This programme does not require the use of detergent.
Light soil. Main wash­Crockery and cutlery Final rinse
NORMAL 65°C Normal soil. Prewash - Main wash
Crockery and cutlery 2 intermediate rinses -
Final rinse - Dry
BIO 50°C Normal soil. Prewash - Main wash
Crockery and 1 intermediate rinse ­cutlery Final rinse - Dry
Before the first use
When using separately special (dishwasher)salt, rinse aid and detergent:
- set the water softener
- add special salt
- fill up with rinse aid
When using tablets that integrate rinse aid and detergent:
there is no need to fill up with rinse aid
- set the water softener
- add special (dishwasher) salt
When using tablets that integrate rinse aid, detergent, salt function and other additives:
there is no need to fill up with special salt or rinse aid.
Check whether these detergents are suitable for your water hardness. Follow the manufacturers instructions.
- Set the water hardness to level 1.
IMPORTANT!
If the drying results are not satisfactory we recommend that you:
1. Fill up the rinse aid dispenser with rinse aid.
2. Set the rinse aid dosage to position 2.
If you decide in future to use separated detergents, we advise that you:
- Fill up the salt and rinse aid container.
- Adjust the water hardness setting to the highest level and perform 1 normal washing programme without loading any dishes.
- Adjust the water hardness setting according to the hardness of the water in your area.
- Adjust the rinse aid dosage
156997390en.qxp 1/17/2007 3:17 PM Page 6
7
Setting the water softener
The dishwasher is equipped with a water softener designed to remove minerals and salts from the water supply, which would have a detrimental or adverse effect on the operation of the appliance.
The softener should be adjusted according to the hardness of the water in your area. Your local Water Authority can advise you on the hardness of the water in your area.
IMPORTANT!
The water softener must be set in both ways: manually and electronically.
Water hardness Adjustment of the water hardness setting
in Clarke
1)
in mmol/l
2)
in °TH
3)
manually electronically
64 - 88 9,0 - 12,5 90 - 125 2 level 10 53 - 63 7,6 - 8,9 76 - 89 2 level 9 46 - 52 6,5 - 7,5 65 - 75 2 level 8 36 - 45 5,1 - 6,4 51 - 64 2 level 7 28 - 35 4,0 - 5,0 40 - 50 2 level 6
18 - 22 2,6 - 3,2 26 - 32 1 level 4
5 - 12 0,7 - 1,8 7 - 18 1 level 2
23 - 27 3,3 - 3,9 33 - 38 2 level 5
13 - 17 1,9 - 2,5 19 - 25 1 level 3
< 5 < 0,7 < 7 1 level 1
no salt necessary
1) Clarke degree, measure of the water hardness.
2) (mmol/l) millimol per litre, international unit for water hardness
3) (°TH) French degree, measure of the water hardness.
The water softener is factory set at position 2.
Setting the water softener manually (see table)
Set switch to position 1 or 2
156997390en.qxp 1/17/2007 3:17 PM Page 7
8
Setting the water softener electronically (see table)
Release the button. The END indicator light will flash. The number of flashes corresponds to current level set.
The END indicator light might flash 5 times, for example. The flashing is repeated every 5 seconds.
To change the level, press the start/cancel button. Each time the button is pressed the level increases. (Level 1 follows level 10).
The END indicator light indicates the new setting. To memorise the operation, turn the programme
selector dial to position off.
Press and hold the start/cancel button and turn the programme selector dial clockwise till the first programme. Keep the button pressed until the programme On/off indicator light and the start/cancel indicator light start flashing.
The water softener is factory set at position 5. The dishwasher must be switched off
Filling with dishwasher salt
Unscrew the cap. Only before filling with
salt for the first time,
fill the salt container with water
Using the funnel provided, pour in the salt until the container is full.
CAUTION!
Use only special salt suitable for dishwashers
156997390en.qxp 1/17/2007 3:17 PM Page 8
9
Remove any trace of salt.
Replace the cap tightly turning it clockwise until it stops with a click.
IMPORTANT!
Immediately start a complete programme.
IMPORTANT!
The salt container will require topping up periodically.
Filling with rinse aid
Open the lid. Fill up with rinse aid.
The maximum level for filling is indicated by "max".
Clean up any rinse aid which overflows. Close the lid and press until it locks.
Top up the rinse aid when the indicator (B) becomes clear.
CAUTION!
Never fill the rinse aid dispenser with any other substances (e.g. dishwasher cleaning agent, liquid detergent). This would damage the appliance.
156997390en.qxp 1/17/2007 3:17 PM Page 9
Loading...
+ 19 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use