Zanussi ZD 29/7 DS3, ZD 29/7 DL3 USER MANUAL

Page 1
REFRIGERADOR-
CONGELADOR
FRIGORIFICO-
CONGELADOR
FRIDGE-FREEZER
ZD 29/7 DS3
ZD 29/7 DL3
MANUAL DE INSTRUÇÕES
INSTRUCTION BOOKLET
2222 236-83
Page 2
14
WARNINGS
It is most important that this instruction book should be retained with the appliance for future reference. Should the appliance be sold or transferred to another owner, or should you move house and leave the appliance, always ensure that the book is supplied with the appliance in order that the new owner can be acquainted with the functioning of the appliance and the relevant warnings.
If this appliance featuring magnetic door seals is to replace an older appliance having a spring lock (latch) on the door or lid, be sure to make that spring lock unusable before you discard the old appliance. This will prevent it from becoming a death-trap for a child.
These warnings are provided in the interest of safety.You must read them carefully before installing or using the appliance.
General Safety
• This appliance is designed to be operated by adults. Children should not be allowed to tamper with the controls or play with the product.
• It is dangerous to alter the specifications or modify this product in any way.
• Before any cleaning or maintenance work is carried out, be sure to switch off and unplug the appliance.
• This appliance is heavy. Care should be taken when moving it
• Ice lollies can cause frost burns if consumed straight from the appliance.
Take utmost care when handling your appliance so as not to cause any damages to the cooling unit with consequent possible fluid leakages.
The appliance must not be located close to radiators or gas cookers.
Avoid prolonged exposure of the appliance to direct sunlight.
There must be adequate ventilation round the back of the appliance and any damage to the refrigerant circuit must be avoided.
For freezers only (except built-in models): an ideal location is the cellar or basement.
Do not use other electrical appliances (such as ice cream makers) inside of refrigerating appliances.
Service/Repair
• Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person
• This product should be serviced by an authorized Service Centre, and only genuine spare parts should be used.
• Under no circumstances should you attempt to repair the appliance yourself. Repairs carried out by inexperienced persons may cause injury or more serious malfunctioning. Refer to your local
Service Centre, and always insist on genuine spare parts.
This appliance contains hydrocarbons in its cooling unit; maintenance and recharging must therefore only be carried out by authorized technicians.
Use
The domestic refrigerators and freezers are designed to be used specifically for the storage of edible foodstuffs only.
Best performance is obtained with ambient temperature between +18°C and +43°C (class T); +18°C and +38°C (class ST); +16°C and +32°C (class N); +10°C and +32°C (class SN).The class of your appliance is shown on its rating plate.
Warning: when the ambient temperature is not included within the range indicated for the class of this appliance, the following instructions must be observed: when the ambient temperature drops below the minimum level, the storage temperature in the freezer compartment cannot be guaranteed; therefore it is advisable to use the food stored as soon as possible.
Frozen food must not be re-frozen once it has been thawed out.
Manufacturers’ storage recommendations should be strictly adhered to. Refer to relevant instructions.
The inner lining of the appliance consists of channels through which the refrigerant passes. If these should be punctured this would damage the appliance beyond repair and cause food loss. DO NOT USE SHARP INSTRUMENTS to scrape off frost or ice. Frost may be removed by using the scraper provided. Under no circumstances should solid ice be forced off the liner. Solid ice should be allowed to thaw when defrosting the appliance.
Do not place carbonated or fizzy drinks in the freezer as it creates pressure on the container, which may cause it to explode, resulting in damage to the appliance.
27
Instalação
Durante o normal funcionamento o condensador e o compressor, colocados na parte de trás do aparelho, aquecem sensivelmente. Por razões de segurança a ventilação deve ser como indicado na respectiva Figura.
Atenção: mantenha as aberturas para a ventilação livres de qualquer obstrução.
O aparelho aquece, sensivelmente, ao nível do con-densador e do compressor. Certifique-se que o ar circula, livremente, à volta do aparelho. Uma ventila-ção insuficiente ocasionaria um mau funcionamen-to, danos para o aparelho e perda dos alimentos no seu interior. Siga as instruções para a correcta instalação do aparelho.
Assegure-se, quando instalar o aparelho, que este não repousa sobre o cabo de alimentação eléctrica. Importante: se o cabo de alimentação se danificar, deverá ser substituído por um cabo especial ou por um conjunto, disponíveis junto do construtor ou do serviço de assistência técnica.
Os componentes do aparelho que aquecem devido ao seu funcionamento não devem estar expostos. Sempre que possível as costas do aparelho devem ficar encostadas a uma parede
Desligue sempre a tomada de corrente antes de proceder à limpeza ou qualquer operação de manutenção do aparelho.
Ao transportar o aparelho na horizontal, pode acontecer que o óleo contido no compressor escorra para o circuito refrigerante. É portanto aconselhável esperar pelo menos duas horas antes de ligar o aparelho à corrente.
Protecão do ambiente
Este aparelho não contem, no seu circuito refrigerante e nas suas matérias isolantes, gases nocivos à camada de ozono.Mesmo assim este aparelho deve, quando for destruido,receber os cuidados convenientes, de acordo com as disposições em vigor para a protecção do melo ambiente. Os materiais utilizados neste aparelho, marcados com o simbolo são reciclàveis.
ÍNSTALAÇÃO
Advertênciase e conselhos importantes 26 Uso e funcionamiento 28
LImpeza das partes internas 28 Arranque 28 Régulação da température 28 Refrigerção dos alimentos 28 Prateleiras amovíveis 29 Colocação das pretelairas da porta 29 Prateleiras para garrafas 29 Recirculação de ar 30 Calendário de congelamento 30 Congelação dos alimentos frescos 31 Congelação dos alimentos congelados 31 Descongelação 31 Fabricação de cubos de gelo 31
Conselhos 32 Conselhos para a refrigeração 32
Conselhos para a congelação 32
Conselhos para a conservação dos alimentos congelados 32 Manutenção 33
Limpeza periódica 33 Paragem prolongada 33 Lâmpada de iluminção 33 Descongelação 33
Assistência técnica e peças de substsuição 34 Dados Técnicos 35 Instalação 35
Colocação 35 Fixadores para prateleiras 35 Ligação elétrica 36 Espaçadores posteriores 36 Reversibilidade das portas 37
Page 3
15
CONTENTS
Warnings 14 Use 16
Cleaning the interior 16 Operation 16 Temperature regulation 16 Fresh food refrigeration 16 Movable shelves 17 Multipurpose shelf 17 Positioning the door shelves 17 Bottle rack 17 Air recycling 18 Freezing calendar 18 Freezing fresh food 19 Storage of frozen food 19 Thawing 19 Ice-cube production 19 Hints 20
Hints for refrigeration 20 Hints for freezing 20
Hints for storage of frozen food 20 Maintenance 21
Periodic cleaning 21 Periods of no operation 21 Interior light 21 Defrosting 21
Customer service and spare parts 22 Technical information 23 Installation 23
Location 23 Shelf holders 24
Electrical connection 24 Rear spacers 24 Changing the opening direction of the doors 25
Installation
• During normal operation, the condenser and compressor at the back of the appliance heat up considerably. For safety reasons, minimum ventilation must be as shown in the instructions.
Attention: keep ventilation openings clear of obstruction.
• Care must be taken to ensure that the appliance does not stand on the electrical supply cable.
Important: if the supply cord is damaged, it must be replaced by a special cord or assembly availa­ble from the manufacturer or its service agent.
• If the appliance is transported horizontally, it is possible that the oil contained in the compressor flows in the refrigerant circuit. It is advisable to wait at least two hours before connecting the appliance to allow the oil to flow back in the compressor.
• There are working parts in this product which heat up. Always ensure that there is adequate ventilation as a failure to do this will result in component failure and possible food loss. See installation instructions.
• Parts which heat up should not be exposed. Wherever possible the back of the product should be against a wall.
Environment Protection
This appliance does not contain gasses which could damage the ozone layer, in either its refrigerant circuit or insulation materials.The appliance shall not be discarded together with the urban refuse and rubbish. Avoid damaging the cooling unit, especially at the rear near the heat exchanger. Information on your local disposal sites may be obtained from municipal authorities.The materials used on this appliance marked by the symbol are recyclable.
26
ADVERTÊNCIAS E CONSELHOS IMPORTANTES
É muito importante que este manual de utilização acompanhe o aparelho para garantir uma futura utilização correcta. Se o aparelho for vendido ou emprestado a uma outra pessoa, o manual de utilização deve, como acima se faz notar, acompanhá-lo, de maneira que o utilizador possa ser informado do seu funcionamento, das advertências e conselhos. Se este aparelho, munido de fecho magnético, veio substituir um outro que tinha portas com fecho de mola, aconselhamos a inutilizar este fecho, antes do aparelho ser posto definitivamente de lado. Esta precaução procura evitar que crianças, brincando, se possam fechar no aparelho o que seria altamente perigoso.
Essas advertências têm por fim garantir a segurança dos utilizadores. Agradecemos, portanto, que leia o manual atentamente, antes de instalar e utilizar o aparelho.
Segurança
Este aparelho foi concebido para ser utilizado por adultos. Deve, por isso, pô-lo ao abrigo das crianças não consentindo que dele se sirvam como brinquedo.
É perigoso modificar ou tentar modificar as características deste aparelho.
Este aparelho é pesado. Tenha o maior cuidado quando o deslocar
Não consuma certos produtos, tais como gelados, imediatamente após terem saído do aparelho; a temperatura muito baixa a que se encontram pode provocar queimaduras.
Este aparelho contém hidrocarbonetos no circuito refrigerante; portanto, a manutenção e a recarga devem ser efectuadas exclusivamente por pessoal autorizado pelo produtor.
Preste a máxima atenção ao deslocar o aparelho, para não danificar as partes do circuito refrigerante, evitando assim possíveis saídas de fluido.
O aparelho não deve ser instalado perto de elementos de aquecimento ou fogões de gás.
Evite a exposição prolongada do aparelho aos raios do sol.
A parte de trás do aparelho deve receber uma suficiente ventilação e deve ser evitado qualquer dano ao circuito refrigerante.
Somente para os congeladores (excepto os de encaixe): a melhor colocação é na cave.
Assistência
Se uma eventual modificação da instalação eléctrica, na casa do utilizador, tiver de ser feita para tornar possível a instalação do aparelho, deve, esta, ser efectuada por pessoal qualificado.
Este aparelho deve ser assistido por um Centro de Assistência autorizado, sendo apenas aplicadas peças de origem.
Em caso de avaria, não tente você mesmo, reparar o aparelho. As reparações executadas por pessoas inexperientes, podem causar danos físicos e mate­riais (aumentando as avarias a serem reparadas).
Faça apelo ao seu Centro de Assistência mais próximo e insista em peças genuínas.
Utilização
Os frigoríficos e/ou congeladores domésticos destinam-se, unicamente, à conservação e/ou congelação de alimentos.
Os melhores rendimentos são conseguidos com temperaturas ambiente incluídas entre +18°C e +43°C (Classe T); +18°C e +38°C (Classe ST); +16°C e +32°C (Classe N); +10°C e +32°C (Classe SN); a classe a que pertence o aparelho é indicada na placa de matrícula (posta na cela ao lado do compartimento dos legumes).
Atenção: com temperaturas ambiente não incluídas nas indicadas para a classe climática a que pertence o produto, é preciso cumprir as indicações seguintes: quando a temperatura ambiente descer abaixo do valor mínimo, pode não ser garantida a temperatura de conservação no compartimento congelador; portanto, aconselha-se a consumar rapidamente os alimentos nele contidos.
Um produto descongelado não deve, em nenhum caso, voltar a ser congelado.
Siga as indicações do fabricante para a conservação e/ou congelação dos alimentos.
O revestimento interior do aparelho em composto de pequenos tubos por onde passa o refrigerante. Se estes tubos forem danificados o aparelho ficará irremediavelmente avariado, provocando a perda dos alimentos no seu interior. NÃO UTILIZE OBJECTOS PONTEAGUDOS para raspar o gelo acumulado.Esse gelo pode ser raspado utilizando a espátula que é fornecida com o aparelho. Para eliminar grandes quantidades de gelo acumulado, é aconselhável deixá-lo derreter.Veja as instruções para a descongelação.
Não coloque no compartimento/congelador a baixa temperatura, garrafas ou latas com bebidas gaseificadas dado que se cria uma pressão elevada no interior da garrafa e/ou lata havendo o perigo de este explodir.Desta explosão resultariam danos graves para o aparelho.
Page 4
16
Cleaning the interior
Before using the appliance for the first time, wash the interior and all internal accessories with luke­warm water and some neutral soap so as to remove the typical smell of a brand-new product, then dry thoroughly.
Do not use detergents or abrasive powders, as these will damage the finish.
Operation
Insert the plug into the wall socket. Open the refrigerator door and turn the thermostat
knob, clockwise, beyond the «O» (STOP) position. The appliance will start to operate.
To stop operation, simply turn the thermostat knob to position «O»
Temperature regulation
The temperature is automatically regulated and can be increased to achieve a higher temperature (warmer) by rotating the thermostat knob toward lower settings or reduced (colder) rotating the knob towards higher settings.
However, the exact setting should be chosen keeping in mind that the temperature inside the refrigerator depends on:
room temperature;
how often the door is opened;
the quantity of food stored;
location of appliance.
A medium setting is generally the most suitable.
Important
If the ambient temperature is high or the appliance is fully loaded, and the appliance is set to the lowest temperatures, it may run continuously causing frost to form on the rear wall. In this case the dial must be set to a higher temperature to allow automatic defrosting and therefore reduced energy consumption.
Fresh food refrigeration
To obtain the best performance:
do not store warm food or evaporating liquids in the refrigerator;
do cover or wrap the food, particularly if it has a strong flavour.
Position food so that air can circulate freely round it.
USE
25
Door reversibility
Before carrying out any operations, remove the plug from the power socket.
To change the opening direction of the door, proceed as follows:
1. pull off the ventilation grille (D) which is clipped into place;
2. remove the bottom hinge (E) by unscrewing its fixing screws;
3. remove the lower door, sliding it out of the middle hinge;
4. unscrew the middle hinge (H);
5. Remove the fridge door by releasing it from the top hinge pin (G).
6. Remove the pin (G) then mount it on the opposite side, after having removed the plugs which must be refitted on the other side.
7. remove the two plugs of the door (where available), discovering the holes for the hinge pins, assemble them on the opposite side and refit the upper door;
8. reassemble the middle hinge on the opposite side;
9. reassemble the lower door;
10.using a 10 mm spanner, unscrew the hinge pin (E) and reassemble it on the opposite side of the hinge;
11. reassemble the lower hinge (E) on the opposite side, using the screws previously removed. Slide the hole cover (F) out of the ventilation grille (D) by pushing it in the direction of the arrow and reassemble it on the opposite side;
12. refit the ventilation grille (D), clipping it into place.
13.Dismantle the handles and reassemble them on the opposite side. Cover the holes left open with the plugs contained in the documentation pack.
The doors can be aligned by adjusting the middle hinge. The middle hinge can be adjusted horizontally, with the help of a tool, after having slackened the two screws.
Warning:
After having reversed the opening direction of the doors check that all the screws are properly tightened and that the magnetic seal adheres to the cabinet. If the ambient temperature is cold (i.e.
in Winter), the gasket may not fit perfectly to the cabinet. In that case, wait for the natural fitting of the gasket or accelerate this process by heating up the part involved with a normal hairdrier.
H
F
D
PR18
F
F
F
E
E
G
D162/1
Page 5
17
Positioning the door shelves
To permit storage of food packages of various sizes, the door shelves can be placed at different heights.
To make these adjustments proceed as follows: Gradually pull the shelf in the direction of the arrows until it comes free, then reposition as required.
D338
Movable shelves
The walls of the refrigerator are equipped with a series of runners so that the shelves can be positioned as desired.
PR260
Bottle rack
Place bottles in the rack with the bottleneck to the front.
Important: Only store unopened bottles horizontally. The bottle rack can be tilted for storing opened
bottles. To do this pull the bottle rack forward until it can be
tilted upwards, then slide the front support into the next level up.
24
Electrical connection
Before plugging in, ensure that the voltage and frequency shown on the serial number plate correspond to your domestic power supply. Voltage can vary by ±6% of the rated voltage.
For operation with different voltages, a suitably sized auto-transformer must be used.
The appliance must be earthed.
The power supply cable plug is provided with a contact for this purpose.
If the domestic power supply socket is not earthed, connect the appliance to a separate earth in compliance with current regulations, consulting a specialist technician.
The Manufacturer declines all responsibility if the above safety precautions are not observed.
This appliance complies with the following E.E.C. Directives:
- 87/308 EEC of 2/6/87 relative to radio interference suppression.
- 73/23 EEC of 19.2.73 (Low Voltage Directive) and subsequent modifications;
- 89/336 EEC of 3.5.89 (Electromagnetic Compatibility Directive) and subsequent modifications.
Rear spacers
In the bag with the documentation, there are two spacers which must be fitted in the two top corners.
Slacken the screws and insert the spacer under the screw head, then re-tighten the screws.
Shelf holders
Your appliance is equipped with shelf retainers that make it possible to secure the shelves during transportation.
To remove them proceed as follows: Move the shelf holders in the direction of the arrow,
raise the shelf from the rear and push it forward until it is freed and remove the retainers.
A
B
C
D594
Page 6
18
Freezing Calendar
The symbols show different types of frozen goods. The numbers indicate storage times in months for the appropriate types of frozen goods.Whether the upper or lower value of the indicated storage time is valid depends on the quality of the foods and pre-treating before freezing.
Air recycling
The refrigerator compartment is equipped with a special D.A.C.(Dynamic Air Cooling) fan which can be turned on with the switch ( see fig. 1). The green light, when on, means that the fan is working.
It is suggested that the fan (D.A.C.) be used when the ambient temperature exceeds 25°C .
It should be remembered that the thermostat knob
must be placed (see fig.2) within the sector . This device allows for rapid cooling of foods and a
more uniform temperature in the compartment.
Fig. 1
Fig. 2
23
TECHNICAL INFORMATION
Energy Efficiency class
A
254
70
0,926
338
4
25
1850
600
625
Net Fridge Capacity lt.
Energy Consumption kWh/24h
Energy Consumption kWh/year
Freezing Capacity 24h
Rising time
Net Freezer Capacity lt.
Dimensions mm
High
Width
Depth
The technical infomation are situated in the rating plate on the internal left side of the appliance .
INSTALLATION
Location
The appliance should be installed well away from sources of heat such as radiators, boilers, direct sunlight etc.
Ensure that air can circulate freely around the back of the cabinet. To ensure best performance, if the appliance is positioned below an overhanging wall unit, the minimum distance between the top of the cabinet and the wall unit must be at least 100 mm (A). Ideally, however, the appliance should not be positioned below overhanging wall units (B). Accurate levelling is ensured by one or more adjustable feet at the base of the cabinet.
A
B
NP004
100 mm10 mm
10 mm
Attention
It must be possible to disconnect the appliance from the mains power supply; the plug must therefore be easily accessible after installation.
O
6
5
4
SWITCH
1
2
3
Page 7
19
Freezing fresh food
The 4-star compartment is suitable for long term storage of commercially frozen food, and for freezing fresh food. To freeze fresh foods it is not necessary to change the setting of the thermostat knob with respect to the normal running position. However, for a quicker freezing operation, turn the thermostat knob to the coldest setting; but remember that, in this condition, the refrigerating compartment temperature might drop below 0°C. If this occurs reset thermostat knob to a warmer setting.
Storage of frozen food
When first starting-up or after a period out of use, before putting the products in the compartment let the appliance run for at least two hours on the coldest setting, then turn the thermostat knob to the normal operating position.
Important
In the event of accidental defrosting, for example due to a power failure, if the power has been off for longer that the value shown in the technical characteristics chart under “rising time”, the defrosted food must be consumed quickly or cooked immediately and then refrozen (after cooling).
Thawing
Deep-frozen or frozen food, prior to being used, can be thawed in the refrigerator compartment or at room temperature, depending on the time available for this operation.
Small pieces may even be cooked still frozen, directly from the freezer: in this case, cooking will take longer.
Ice-cube production
This appliance is equipped with one or more trays for the production of ice-cubes. Fill these trays with water, then put them in the freezer compartment.
Do not use metallic instruments to remove the trays from the freezer.
22
CUSTOMER SERVICE AND SPARE PARTS
If the appliance is not functioning properly, check that:
the plug is firmly in the wall socket and the mains power switch is on;
there is an electricity supply (find out by plugging in another appliance);
the thermostat knob is in the correct position.
If there are water drops on the bottom of the cabinet, check that the defrost water drain opening is not obstructed (see “Defrosting” section).
If your appliance is still not working properly after making the above checks, contact the nearest service centre.
To obtain fast service, it is essential that when you apply for it you specify the model and serial number of your appliance which can be found on the guarantee certificate or on the rating plate located inside the appliance, on the bottom left-hand side.
The freezer compartment, however, will become progressively covered with frost. This should be removed with a plastic scraper, whenever the thickness of the frost exceeds 4 mm. During this operation it is not necessary to switch off the power supply or to remove the foodstuffs.
Never use sharp metal tools to scrape off frost from the evaporator as you could damage it.
However, when the ice becomes very thick on the inner liner, complete defrosting should be carried out as follows:
1. pull out the plug from the wall socket or turn the thermostat knob to the «O» setting;
2. remove any stored food, wrap it in several layers of newspaper and put it in a cool place;
3. leave the door open;
4. when defrosting is completed, dry the interior thoroughly;
5. turn the thermostat knob back to the required setting or replace the plug in the power socket.
6. After two or three hours, reload the previously removed food into the compartment.
Important:
A temperature rise of the frozen food packs, during defrosting, may shorten their safe storage life.
Never use sharp metal tools to scrape off frost from the evaporator as you could damage it.
Do not use a mechanical device or any artificial means to speed up the thawing process other than those recommended by the manufacturer.
Page 8
20
HINTS
Hints for refrigeration
Useful hints: Meat (all types): wrap in polythene bags and place
on the glass shelf above the vegetable drawer.
For safety, store in this way only one or two days at the most.
Cooked foods, cold dishes, etc..: these should be
covered and may be placed on any shelf. Fruit and vegetables: these should be thoroughly
cleaned and placed in the special drawer(s) provided.
Butter and cheese: these should be placed in special airtight containers or wrapped in aluminium foil or polythene bags to exclude as much air as possible.
Milk bottles: these should have a cap and should be stored in the bottle rack on the door.
Bananas, potatoes, onions and garlic, if not packed, must not be kept in the refrigerator.
Hints for freezing
To help you make the most of the freezing process, here are some important hints:
Place the food to be frozen on the freezer shelf as this is the coldest part.
the maximum quantity of food which can be frozen in 24 hrs. is shown on the rating plate;
the freezing process takes 24 hours. No further food to be frozen should be added during this period;
only freeze top quality, fresh and thoroughly cleaned, foodstuffs;
prepare food in small portions to enable it to be rapidly and completely frozen and to make it possible subsequently to thaw only the quantity required;
wrap up the food in aluminium foil or polythene and make sure that the packages are airtight;
do not allow fresh, unfrozen food to touch food which is already frozen, thus avoiding a rise in temperature of the latter;
lean foods store better and longer than fatty ones; salt reduces the storage life of food;
water ices, if consumed immediately after removal from the freezer compartment, can possibly cause the skin to be freeze burnt;
Hints for storage of frozen food
To obtain the best performance from this appliance, you should:
make sure that the commercially frozen foodstuffs were adequately stored by the retailer;
be sure that frozen foodstuffs are transferred from the foodstore to the freezer in the shortest possible time;
not open the door frequently or leave it open longer than absolutely necessary.
Once defrosted, food deteriorates rapidly and cannot be refrozen.
Do not exceed the storage period indicated by the food manufacturer.
it is advisable to show the freezing-in date on each individual pack to enable you to keep tab of the storage time;
do not put carbonated liquids (fizzy drinks, etc.) in the freezer compartment as they may burst.
21
MAINTENANCE
Unplug the appliance before carrying out any maintenance operation.
Warning
This appliance contains hydrocarbons in its cooling unit; maintenance and recharging must therefore only be carried out by authorized technicians.
Periodic cleaning
Many proprietary kitchen surface cleaners contain chemicals that can attack/damage the plastics used in this appliance. For this reason it is recommended that the outer casing of this appliance is only cleaned with warm water with a little washing-up liquid added.
Clean the inside with warm water and bicarbonate of soda.
Rinse and dry thoroughly. Clean the condenser (black grill) and the
compressor at the back of the appliance with a brush or a vacuum cleaner.This operation will improve the performance of the appliance and save electricity consumption.
Periods of non-operation
When the appliance is not in use for long periods, take the following precautions:
remove the plug from the wall socket; remove all food; defrost and clean the interior and all accessories; leave the door ajar to allow air to circulate to prevent
unpleasant smells.
Interior light
The light bulb inside the refrigerator compartment can be reached as follows:
unscrew the light cover securing screw.
unhook the moving part as shown in the figure.
If the light does not come on when the door
is open, check that it is screwed into place properly. If it still does not light up, change the bulb.The rating is shown on the light bulb cover.
Defrosting
Frost is automatically eliminated from the evaporator of the refrigerator compartment every time the motor compressor stops, during normal use. The defrost water drains out through a trough into a special container at the back of the appliance, over the motor compressor, where it evaporates.
It is important to periodically clean the defrost water drain hole in the middle of the refrigerator compartment channel to prevent the water overflowing and dripping onto the food inside. Use the special cleaner provided, which you will find already inserted into the drain hole.
D037
D411
Loading...