Zanussi ZD25/6DS5 USER MANUAL

16

m These domestic refrigerators are designed to be

used specifically for the storage and conserva­tion of food.

m DO NOT USE SHARP INSTRUMENTS to

scrap off frost or ice. Frost may be removed by
using a plastic scraper. (See defrosting instruc­tions).

m Frozen food must not be re-frozen once it has

been thawed out.

m Manufacturer’s storage recommendations

should be strictly complied with.

m Lollies can cause frost burns if consumed right

away from the freezer.

m Do not place carbonate or fizzy drinks in the

freezer as these may explode.

m When an old freezer is to be discarded make

sure to:

m Dismount the doors in order to prevent chil-

dren from getting trapped inside.
Have the gas from the cooling system with-

drawn before making it to scrap iron.

mm

Warnings for your safety

Warnings for your safety. Carefully read
these instructions before installing and
using the machine.

m This freezer is designed to be operated by adults

only. Children should not be allowed to tamper with
the controls or play with the product.

m Make sure that the power plug is not squashed or

damaged by the back of the fridge/freezer. Do not
place heavy articles or the fridge/freezer itself on
the power cord. Do not remove the power cord by
pulling on its lead, particularly when the fridge/fre­ezer is being pulled out of its niche. If the power
plug socket is loose, do not insert the power plug. If
the power cord is damaged, it must be replaced by
a certified service agent or qualified service person­nel. Damage to the cord may cause a
shortcircuit,fire and/or electric shock.

m This appliance is heavy. Care should be taken when

moving it.

m Repairs carried out by inexperienced persons may

cause injuries or serious malfunctioning. Refer to
the nearest Authorized Dealer.

m Make sure the rear part of the appliance stands

against a wall as there are working parts which heat
up and should not be of easy access.

m Make sure that there is a continous and adequate

ventilation as a failure to do so may result in dama­ge to the appliance or deterioration of the food.

m The appliance should be left for at least 4 hours

after installation before it is turned on ill order to
allow the refrigerant to settle.

m This product must be serviced only by an AUTHO-

RIZED DEALER, and only GENUINE SPARE
PARTS must be employed.

m Before cleaning or reparing the appliance, make

sure it is unplugged.

m It is dangerous to alter the specifications or modify

this product in any way.

17

Índex

Warnings for your safety pag. 16

Installation pag. 18

Changing the opening directions
of the doors and Panelling pag. 19 - 20

Regulation and Control pag. 21

How to use your
Refrigerator-Freezer pag. 22 - 23

Maintenance of your
Refrigerator-Freezer pag. 24 - 25

Something not working pag. 26 - 27

Normal noises when
functioning pag. 28

Guarantee, Service
and Spare Parts pag. 29

Tecnical Features pag. 30

18

Installation

Before Positioning

• Read this Instruction Book

• In the documentation bag you will find two spacers
that must be mounted as shown in the figure in the
back of your appliance.
Please loosen the screw under its head and then
unloosen again.

Positioning

• Place the refrigerator away from direct sunlight and
heat sources.

• Maintain recommended ventilation - see Fig. 1.

• Make sure the refrigerator is accurately levelled tur­ning the adjustable feet in order to avoid vibrations
and noises, Fig. 2.

• This is a built in design to be aligned with other fur­niture

• The appliance must be located in places of maxi­mum temperature as follows:

If the temperature are higher than these both above
mentioned, the functions of appliance coudl result
reduced.

Cleaning the interior

• Do not use alcohol or any cleanig product contai­ning alcohol because it can damage the cabinet.

• Before using the appliance for the first time wash
the interior whith luke warm water and some neutral
soap so as to remove the typical smell of a brand­new product arid then dry thoroughly.

• Do not use detergents or abrasive powders as these
will damage the finish.

• Remove security used for transportation.

Electrical connection

mBefore plugging the appliance make sure that the

voltage and frequency shown on the «Technical
Features» correspond to your home supply.

mIt is essential that the appliance be efficiently

earthed.
For this purpose the supply cable plug incorporates
a special earth contact. If the sockets of your domes­tic wiring system are not grounded, have the
appliance connected to a separate ground wire in
accordance with existing safety regulations.
«THE MANUFACTURER DECLINES TO
ACCEPT ANY LIABILITY IF THIS SAFETY
RULE IS NOT OBSERVED».

Starting – up

• Plug the appliance into the mains.

• Make sure the inner light turns on when opening the
door.

• Turn to intermediate position the knobs of the «tem­perature regulator» «A».

Fig. 2

Fig. 1

SN +10 to +32ºC
N +16 to +32ºC
ST +18 to +38ºC
T +18 to +43ºC

D594

19

Changing the opening direction
of doors and Panelling

If you wish to change the opening side of the doors
proceed as follows:

1... Remove the handles of the doors, if they are side
fixing by screws.

2... Take off the plinth pressed on to.

3... Remove the inferior hing taking care for the dow­ner door not to fall off and not to lose the plastic
spacer. Using a 10mm spanner, unscrew the hinge
pin and reassemble it on the opposite side.

4... Lift the downer door off the central hinge.

5... Remove the central hinge taking care for the upper
door not to fall off .

6... Take the upper door off the upper hinge. Be careful
not to lose the plastic ring.

7... Unscrew the plastic bolts of the opposite side of the
place of the central hinge taken out and introduce
them in the holes occupied before by the hinge.

20

Changing the opening direction
of doors and Panelling

If your refrigerator has top panel, you can manage in
the same way from point 1 to point 7 and then:

9... Unscrew the axle of the upper hing (9) and replace
it at the opposite side (10).

For the remaining parts proceed the other way round.

Once finished make sure that all joints close
perfectly well all around the door and chek that the
internal light turns of when the fridge door closes.

How to panel the door:

If your appliance is provided with metal strips for
panelling and you wish to do so proceed as follows:

1... Remove one of the side strips.

2... Loosen the screws of the remaining strips.

3... Start putting on the panel where you took off the
strip pushing it right up to the end.

4... Replace the strip on this side.

5... Tighten all screws

NOTE:

The panel dimensions must be 2 mm. shor­ter than the doors. Maximun thickness of
the panel is 4 mm.