Zanussi ZD25/6ATT USER MANUAL
m Warnings for your Safety
Warnings for your safety. Carefully read these
instructions before installing and using the
machine.
m This freezer is designed to be operated by adults
only. Children should not be allowed to tamper
with the controls or play with the product.
m Any electrical work required to install the applian-
ce should be carried out by a qualified electrician
or competent person.
m This appliance is heavy. Care should be taken
when moving it.
m Make sure that the cable is not trapped underne-
ath the appliance, nor touches the motor.
m Repairs carried out by inexperienced persons
may cause injuries or serious malfunctioning.
Refer to the nearest Authorized Dealer.
m Make sure the rear part of the appliance stands
against a wall as there are working parts which
heat up and should not be of easy access.
m Make sure that there is a continous and adequate
ventilation as a failure to do so may result in
damage to the appliance or deterioration of the
food.
HORIZED DEALER, and only GENUINE SPARE
PARTS must be employed.
m Before cleaning or reparing the appliance, make
sure it is unplugged.
m It is dangerous to alter the specifications or modify
this product in any way.
m These domestic refrigerators are designed to be
used specifically for the storage and conservation
of food.
m DO NOT USE SHARP INSTRUMENTS to scrap
off frost or ice. Frost may be removed by using a
plastic scraper. (See defrosting instructions).
m Frozen food must not be re-frozen once it has
been thawed out.
Manufacturers storage recommendations should
be strictly complied with.
m Lollies can cause frost burns if consumed right
away from the freezer.
m Do not place carbonate or fizzy drinks in the free-
zer as these may explode.
m When an old freezer is to be discarded make sure
to:
m The appliance should be left for at least 4 hours
after installation before it is turned on ill order to
allow the refrigerant to settle.
m This product must be serviced only by an AUT-
m Dismount the doors in order to prevent children
from getting trapped inside.
Have the gas from the cooling system with-
drawn before making it to scrap iron.
Index
Warnings for your safety. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Installation Positioning/Cleaning the interior/Electrical connection/Starting up. . . . . . . . . . . . . . . . . . . . . . 12
Changing the opening directions of the doors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Control and Use Control /Interior Light/Dinamic Refrigeration DAC/Inner Door Compartments
Position/Shelves Position. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . .14
Control and Use Freezer Compartment/Refrigerator Compartment . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Maintenance Defrosting of the freezer/Defrosting of the fridge. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Something not working . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-18
Normal noises when functioning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Guarantee, Service and Spare Parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Tecnical Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
11
Installation
Positioning
Place the refrigerator away from direct sunlight
and heat sources.
Maintain recommended ventilation - see Fig. 1.
Fig. 1
Make sure the refrigerator is accurately levelled
turning the adjustable feet in order to avoid vibrations and noises, Fig. 2.
Fig. 2
Cleaning the interior
Do not use alcohol or any cleanig product contai-
ning alcohol because it can damage the cabinet.
Before using the appliance for the first time wash
the interior whith luke warm water and some neutral soap so as to remove the typical smell of a
brand-new product arid then dry thoroughly.
Do not use detergents or abrasive powders as
these will damage the finish.
Remove security used for transportation.
Electrical connection
m Before plugging the appliance make sure that the
voltage and frequency shown on the «Technical
Features» correspond to your home supply.
It is essential that the appliance be efficiently
earthed.
m For this purpose the supply cable plug incorpora-
tes a special earth contact. If the sockets of your
domestic wiring system are not grounded, have
the appliance connected to a separate ground wire
in accordance with existing safety regulations.
«THE MANUFACTURER DECLINES TO ACCEPT
ANY LIABILITY IF THIS SAFETY RULE IS NOT
OBSERVED».
This is a built in design to be aligned with other
furniture
The appliance must be located in places of maxi-
mum temperature as follows:
SN +10 to +32ºC
N +16 to +32ºC
ST +18 to +38ºC
T +18 to +43ºC
If the temperature are higher than these both
above mentioned, the functions of appliance coudl
result reduced.
With the freezer door wide-open, assemble the
socle provided inside the appliance, following the
instructions stuck on it.
Starting up
Plug the appliance into the mains.
Make sure the inner light turns on when opening
the door.
Turn to intermediate position the knobs of the
«temperature regulator» «A» (See Control And
Use paragraph).
12
Changing the opening direction of doors
If you wish to change the opening side of the doors
proceed as follows:
1... Take off the plinth (D) pressed onto cabinet. Take
out the lid (F) and put it into the opposite hole.
E
F
F
D
PR18b
F
E
F
2... Remove the lower hinge (E) taking care for the
lower door not to fall off. Dismantle the lower
hinge reinforcement (Z) and assemble it in the
opposite side.
7 Unscrew the axle of the upper hing and screw it
into the hinge on the opposite side. Make sure to
fit in the metal washer for blocking.
8 Place upper door.
9... Put the central hinge (H) in the opposite side from
original position. Leave the hinge loose.
10...Place the lower door next to the lower hinge (E)
in the opposite side from original and fix all the
hinges.
11...Dismantle the vertical handles and assemble
them in the opposite side. Cover the holes with
the plastic lids that were situated where the handles are presently.
PR220
12...Replace the plinth well fixed.
3... Lift the lower door off the central hinge (H).
H
4... Remove the central hinge (H) taking care for the
upper door not to fall off and not to lose the plastic washer.
5... Take the upper door off the upper hinge (G). Be
carefull not to lose the plastic washer.
G
mm
Once finished make sure that all joints close
perfectly well all around the door and chek that
the internal light turns of when the fridge door
closes.
How to panel the door:
If your appliance is provided with metal strips for
panelling and you wish to do so proceed as
follows:
1...Remove one of the side strips.
2...Loosen the screws of the remaining strips.
3...Start putting on the panel where you took off the
strip pushing it right up to the end.
4...Replace the strip on this side.
5...Tighten all screws
NOTE: The panel dimensions must be 2 mm. shorter than the doors. Maximun thickness of the panel
is 4 mm.
6... Unscrew the plastic plugs located on the opposite side of the central hinge and introduce them in
the holes occupied before by the hinge.
13
Loading...