Zanussi ZD23/5R3 User Manual

Warnings for your safety
Warnings for your safety. Carefully read these ins­tructions before installing and using the machine.
This freezer is designed to be operated by adults only. Children should not be allowed to tamper with the controls or play with the pro­duct.
Any electrical work required to install the appliance should be carried out by a qualified electrician or competent person.
This appliance is heavy. Care should be taken when moving it.
Make sure that the cable is not trapped under­neath the appliance, nor touches the motor.
Repairs carried out by inexperienced persons may cause injuries or serious malfunctioning. Refer to the nearest Authorized Dealer.
Make sure the rear part of the appliance stands against a wall as there are working parts which heat up and should not be of easy access.
Frozen food must not be re-frozen once it has been thawed out. Manufacturers storage recommendations should be strictly complied with.
Lollies can cause frost burns if consumed right away from the freezer.
Do not place carbonate or fizzy drinks in the freezer as these may explode.
When an old freezer is to be discarded make sure to:
Dismount the doors in order to prevent children from getting trapped inside.
Have the gas from the cooling system withdrawn before making it to scrap iron.
Make sure that there is a continous and ade­quate ventilation as a failure to do so may result in damage to the appliance or deteriora­tion of the food.
The appliance should be left for at least 4 hours after installation before it is turned on ill order to allow the refrigerant to settle.
This product must be serviced only by an AUT­HORIZED DEALER, and only GENUINE SPARE PARTS must be employed.
Before cleaning or reparing the appliance,
make sure it is unplugged.
It is dangerous to alter the specifications or modify this product in any way.
These domestic refrigerators are designed to be used specifically for the storage and conser­vation of food.
DO NOT USE SHARP INSTRUMENTS to scrap off frost or ice. Frost may be removed by using a plastic scraper. (See defrosting instruc­tions).
15
Índex
Warnings for your safety pag. 15
Installation pag. 17
Changing the opening directions of the doors and Panelling pag. 18
Regulation and Control pag. 19
How to use your Refrigerator-Freezer pag. 20 - 21
Maintenance of your Refrigerator-Freezer pag. 22 - 23
Something not working pag. 24 - 25
Normal noises when functioning pag. 26
Guarantee, Service and Spare Parts pag. 27
Tecnical Features pag. 28
16
Installation
Positioning
 Place the refrigerator away from direct sunlight
and heat sources.  Maintain recommended ventilation - see Fig. 1.  Make sure the refrigerator is accurately levelled
turning the adjustable feet in order to avoid vibra-
tions and noises, Fig. 2.  This is a built in design to be aligned with other fur-
niture  The climate classification can be found on the
serial plate, which is located at the left on the insi-
de of the appliance.
The following table shows which ambient tempera-
ture is correct for each climate classification:
Climate classification for an ambient temperature of
SN + 10 to + 32°C
N + 16 to + 32°C
ST + 18 to + 38°C
T + 18 to + 43°C
Fig. 1
Cleaning the interior
 Do not use alcohol or any cleanig product contai-
ning alcohol because it can damage the cabinet.  Before using the appliance for the first time wash
the interior whith luke warm water and some neu-
tral soap so as to remove the typical smell of a
brand-new product arid then dry thoroughly.  Do not use detergents or abrasive powders as
these will damage the finish.  Remove security used for transportation.
Electrical connection
Before plugging the appliance make sure that the
voltage and frequency shown on the «Technical
Features» correspond to your home supply.
It is essential that the appliance be efficiently
earthed.
For this purpose the supply cable plug incorpora-
tes a special earth contact. If the sockets of your
domestic wiring system are not grounded, have
the appliance connected to a separate ground wire
in accordance with existing safety regulations.
«THE MANUFACTURER DECLINES TO ACCEPT
ANY LIABILITY IF THIS SAFETY RULE IS NOT
OBSERVED».
Fig. 2
Starting  up
 Plug the appliance into the mains.  Make sure the inner light turns on when opening
the door.  Turn to intermediate position the knob of the «tem-
perature regulator» «A».
17
Changing the opening direction of doors and Panelling
If you wish to change the opening side of the doors proceed as follows:
1... Remove the handles of the doors, if they are side
fixing by screws.
2... Take off the plinth pressed on to.
3... Remove the inferior hing taking care for the dow-
ner door not to fall off.
4... Lift the downer door off the central hinge. Using a
10mm spanner, unscrew the hinge pin and reas­semble it on the opposite side.
5... Remove the central hinge taking care for the
upper door not to fall of and not to lose the plas­tic spacer.
6Take the upper door off the upper hinge. Be care-
full not to lose the plastic ring.
7Unscrew the plastic bolts of the opposite side of
the place of the central hinge taken out and intro­duce them in the holes occupied before fy the hinge.
8Unscrew the axe of the upper hinge and screw it
to the hinge on the opposite side. Maker sure to fit in the metal spacer for blocking. Place upper door. Assemble the lower hinge reinforcement in the opposite side it was situated. For the remaining parts proceed the other way round.
Once finished make sure that all joints close perfectly well all around the door and chek that the internal light turns of when the fridge door closes.
How to panel the door:
If your appliance is provided with metal strips for panelling and you wish to do so proceed as follows:
1... Remove one of the side strips.
2... Loosen the screws of the remaining strips.
3... Start putting on the panel where you took off the
strip pushing it right up to the end.
4... Replace the strip on this side.
5... Tighten all screws
NOTE: than the doors. Maximun thickness of the panel is 4 mm.
18
The panel dimensions must be 2 mm. shorter
Regulation and Control
Temperature Regulator for Refrige­rator:
Allows to adjust the temperature inside the refrigera­tor according to use and external conditions.  Pos. 1 = Minimum cold.  Pos. 6 = Maximum cold.  Pos. 0 = Motor disconnected
«A»
A
Interior light:
Comes on when opening the door of the refrigerating compartment and shuts off when you close the door. It also switchs off when you put the temperature regulator in position 0. When changing the light bulb, first pull out the screw «Y» and then remove the protective cover «X». (see point , «IF SOMETHING DOES NOT WORK»).
«H»
19
Loading...
+ 9 hidden pages