Zanussi ZD19/4R-1 USER MANUAL
m
Warnings for your safety
Warnings for your safety. Carefully read
these instructions before installing and
using the machine.
m This freezer is designed to be operated by adults.
Children should not be allowed to tamper with the
controls or play with the product.
m Any electrical work required to install the applian-
ce should be carried out by a qualified electrician or
competent person.
m This appliance is heavy. Care should be taken when
moving it.
m Make sure that the cable is not trapped underneath
the appliance, nor touches the motor.
m Repairs carried out by inexperienced persons may
cause injuries or serious malfunctioning. Refer to
the nearest Authorized Dealer.
m Frozen food must not be re-frozen once it has
been thawed out.
m Manufacturers storage recommendations
should be strictly complied with.
m The lollies can cause frost burns if consumed
right away from the freezer.
m Do not place carbonate or fizzy drinks in the
freezer as these may explode.
m Whenever there is a need for discarding an old
freezer make sure to:
m Take off the doors in order to prevent chil-
dren trapped inside.
Have the gas from the cooling system reco-
vered before making it to scrap iron.
m Make sure the rear part of the appliance stands
against a wall as there are working parts which heat
up and should not be of easy access.
m Make sure that there is a continous and adequate
ventilation as a failor to do so will result in component failure and possible food loss.
m The appliance should be left for at least 4 hours
after installation before it is turned on ill order to
allow the refrigerant to settle.
m This product must be serviced only by an authori-
zed NETWORK SERVICE CENTRE, and only
genuine SPARE PARTS must be employed.
m Before cleaning or reparing the appliance, make
sure it is unplugged.
m It is dangerous to alter the specifications or modify
this product in any way.
m These domestic refrigerators are designed to be used
specifically forthe storage andconservation of food.
m DO NOT USE SHARP INSTRUMENTS to scrap
off frost or ice. Frost may be removed by using a
plastic scraper. (See defrosting instructions).
15
Índex
Warnings for your safety pag. 15
Installation pag. 17
Changing the opening directions
of the doors and panelling pag. 18 - 19
Regulation and Control pag. 20
How to use your
Refrigerator-Freezer pag. 21
Maintenance of your
Refrigerator-Freezer pag. 22 - 23
Something not working pag. 24 - 25
Normal noises when
functioning pag. 26
Guarantee, Service
and Spare Parts pag. 27
Tecnical Features pag. 28
16
Installation
Positioning
Place the refrigerator away from direct sunlight and
heat sources.
Maintain recommended ventilation - see Fig. 1.
Make sure the refrigerator is accurately levelled tur-
ning the adjustable feet in order to avoid vibrations
and noises Fig. 2.
This is a built in design to be aligned with other fur-
niture.
The appliance should be only set up at a location
whose ambient temperature corresponds to the cli-
mate classification, for which the appliance is desig-
ned.
The climate classification can be found on the serial
plate of the appliance.
The following table shows which ambient tempera-
ture is correct for each climate classification:
Climate classification for an ambient temperature of
SN + 10 to + 32°C
N + 16 to + 32°C
ST + 18 to + 38°C
T + 18 to + 43°C
However, the manufacturer make sure the correct
operation of the appliance from minimum tempera-
ture of 10°C to upper limit of each climatic class.
wiring system are not grounded, have the
appliance connected to a separate ground wire in
accordance with existing safety regulations.
«THE MANUFACTURER DECLINES TO
ACCEPT ANY LIABILITY IF THIS SAFETY
RULE IS NOT OBSERVED».
Starting up
Plug the appliance into the mains.
Turn to intermediate position the knobs of the
«temperature regulators» «A» Fig. 5.
Make sure the inner light «H» turns on when
opening de door.
Cleaning the interior
Do not use alcohol or any cleanig product containing
alcohol because it can damage the cabinet.
Before using the appliance for the first time wash the
interior whith luke warm water and some neutral
soap so as to remove the typical smell of a brand-
new product and then dry thoroughly.
Do not use detergents or abrasive powders as these
will damage the finish.
Remove security used for transportation.
Electrical connection
mBefore plugging the appliance into a socket make
sure that the voltage and frequency shown on the
rating plate correspond to your home supply.
mIt is essential that the appliance be connected to an
efficient earth tap.
For this purpose the supply cable plug incorporates a
special earth contact. If the sockets of your domestic
Fig. 1
Fig. 2
17
Changing the opening direction
of doors and Panelling
Changing the opening direction of
the doors
If you wish to change the opening side of the doors
proceed as follows:
1... Remove the handles of the doors, if they are side
fixing by screws.
2... If your appliance carries a plinth, remove it pulling
from it smoothly. Take off the small lid on the left
(to let the lower hinge enter into it) and place it on
the right side of the plinth.
3... Remove the lower hing taking care for the lower
door not to fall off. You could have better access to
the lower hinge by tilting the refrigerator.
4... Lift the lower door off the central hinge.
5... Remove the central hinge taking care for the upper
door not to fall off and not to lose the plastic
washer.
6... Take the upper door off the upper hing.
7... The upper hing must be removed, removing at
once, the plastic lid covering it.
8... All small plastic covers are useful now to cover
new holes on the opposite side of the doors.
Fig. 3
18
Changing the opening direction
of doors and Panelling
If you refrigerator has top panel (fig. 4), you can manage in the same way from point 1 to point 6 and then:
7... Unscrew the axle of the upper hing (9 Fig. 4) and
replace it at the opposite side (10 Fig. 4).
8... Remove the little lid put on the opposite side of the
central hinge and use it to cover the new holes left
where the hinge was placed.
Fig. 4
For the remaining parts proceed the other way round.
Once finished make sure that all joints close
perfectly well all around the door and chek that the
internal light turns of when the fridge door closes.
How to panel the doors:
If your appliance is provided with metal strips for
panelling and you wish to do so proceed as follows:
1... Remove one of the side strips.
2... Loosen the screws of the remaining strips.
3... Start putting on the panel where you took off the
strip pushing it right up to the end.
4... Replace the strip on this side.
5... Tighten all screws
NOTE:
than the doors. Maximun thickness of the panel is
4 mm.
The panel dimensions must be 2 mm. shorter
19
Loading...