Zanussi 2530, 2520 SERVICE BULLETIN

WASHING

2520-2530

SERVICE BULLETIN

MODIFICATION OF ANCHORS FOR G11/G19/G12 (42-46 litres)

As from serial no. 901..., the system used to anchor the lifters on G11/G19 drums (capacity 42 litres) and
G12 (capacity 46 litres), fitted to a large number of washing machine/washer dryers models in the P6000
range with stainless steel (G11/G12) and carboran (G19) tubs.
The new system of anchoring the lifters limits possible movement and thus reduces the possibility of
detachment from the drum.

PART NOS.

Pos. Description Old part no. New part no.

262 Lifter 124 00 69-11/0 -------------------­262 Lifter + screw -------------------- 5025 22 71-00/7

PART NOS. DRUM COMPLETE (Pos. 250)

Part no. before

modification

124 02 90-02/1 124 02 90-08/8 G11/G19 (42 l) 400 --------

124 02 90-33/6 124 02 90-38/5 G11/G19 (42 l) 500-600 124 02 90-31/0

124 02 90-51/8 124 02 90-58/3 G11/G19 (42 l) 1000-1200 --------

124 02 90-71/6 124 02 90-78/1 G12 (46 l) 1000-1200 --------

124 02 91-42/5 124 02 91-47/4 G11/G19 (42 l) 1400-1500 124 02 91-40/9

124 02 91-52/4 124 02 91-57/3 G12 (46 l) 1400-1500 124 02 91-50/8

124 02 91-63/1 124 02 91-67/2 G11/G19 (42 l) 1000 124 02 91-60/7

124 63 26-30/8 124 63 26-33/2 G11/G19 (42 l) 1200 --------

124 63 26-40/7 124 63 26-43/1 G12 (46 l) 1200 --------

124 63 26-80/3 124 63 26-81/1 G12 (46 l) 650-850 124 02 90-63/3 124 02 90-66/6

124 63 26-90/2 124 63 26-91/0 G11/G19 (42 l) 650-850 124 02 09-02/7 124 02 90-46/8

INTERCHANGEABILITY

The modified drum is perfectly interchangeable with the one before the modification.
If the lifter is to be replaced, use the kit (lifter + stainless steel screw) code 5025 22 71-00/7, which can be
fitted to the old and new drums alike.

New part no. Type Spin

(rpm)

Previous part nos. replaced by

drum before the modification

\

EN Publication no.

599 33 73-59/5

1/2

Service 99-01-25 - ITZ

FITTING THE NEW DRUM LIFTER

Removal:

a. Insert a screwdriver into the fourth hole in the lifter and

bend back the anchor tabs as shown in the figure.

b. Pull the lifter outwards (towards the door) and detach from

the drum.

Replacement:

a. Check that the anchor tabs are parallel to the drum

casing.

b. Insert the new lifter into the drum and push towards the

rear of the appliance.

c. Disconnect the tube between the tub and the filter body.

d. Tighten the screw (through the hole in the tub) to secure

the lifter to the drum.

2/2