ZANO LED MODULES
Flicker-free and silent LED dimming
For optimum
performance the
dimmer
into programming
mode
must be put
to calibrate
the load
WIRING INSTRUCTIONS
Dimmer Switch and dimmer
DIMMER
L2 L1 C
LIVE FEED
LAMP/LOAD
2-WAY
SWITCH
L2 L1 C L2 L1 C
DIMMER
LAMP/LOAD
LIVE FEED
INSTALLATION
NB: Installation must be carried out by a qualified electrician
Turn off the mains at distribution board
•
Wire device using a suitable rated cable as in wiring diagrams.
•
Terminals should be tightened to a maximum of 0.33Nm.
•
Check polarity is correct throughout.
•
Fit appropriate adaptor as in assembly diagrams.
•
Fit device into wall box ensuring cables are not obstructed.
•
Secure front plate.
•
Product should be recycled at end of life where facilities exist.
•
SMART SETTINGS INSTALLATION GUIDE
Please read through before you begin…
1. Turn on the lights and turn control clockwise to full brightness.
2. Press to turn off.
3. While off, turn the controller fully anti-clockwise
4. Press again to turn on. The lights will flash to indicate that you
are now in programming mode.
5. Select the minimum light level required
6. Wait 5 seconds. The lights will flash again to indicate the minimum
level has been stored
7. You are now going to set the start level – turn controller clockwise
to a brighter level
8. Wait 5 seconds. The lights will flash again to indicate the start level
has been stored
9. The lights will now come on at maximum brightness
a. If flicker is seen, adjust the controller down until the flicker
stops and again, wait 5 seconds for the settings to be stored.
b. If you are unable to see any flicker wait 5 seconds and the
lights will flash confirming all smart settings have been saved
10. Your dimmer is now set and ready to use. All settings will be saved
even if the power is switched off.
SPECIFICATIONS
PART NO. ZMO150 ZMC250 ZMO250
MODULE SIZE SINGLE GRID SINGLE GRID SINGLE GRID
POT POSITION OFFSET FOR PLATE MOUNTING CENTRE FOR GRID APPLICATION OFFSET FOR PLATE MOUNTING
LAMP TYPE LED LED LED
MAX WATT 150W / VA 250W / VA 250W / VA
MIN WATT 0W / VA 5W / VA 5W / VA
MIN BOX DEPTH 35 MM 35 MM 35 MM
2-WAY SWITCHING YES YES YES
NEED TO DE-RATE TO 160W / VA N/A YES IF FITTING 2 OR MORE PER PLATE YES IF FITTING 2 OR MORE PER PLATE
MAXIMUM PLATE LOAD RECOMMENDATIONS
COVER PLATE SIZE CFL LED
SINGLE PLATE 500W 500W
DOUBLE PLATE 640W 640W
6-8 GANG 1280W 1280W
We are award-winning manufacturers of LED dimming solutions
and pride ourselves on providing fast, friendly, expert advice.
For our full range of products, technical advice & instructional
films or to find your nearest stockists please see our website.
GUARANTEE
For lamp test results and our full terms and conditions please
see our website: www.zanocontrols.co.uk.
PRODUCT OVERVIEW
The Zano LED modules have been specifically designed to dim LED
lamps. The advance technology used to control the load results in
flicker-free and silent dimming of lamps and drivers. The technology
also eliminates the need to differentiate between leading and trailing
edge lamps. It works with both. All of our LED dimmers have built-in
thermal and over-load protection, as well as our smart settings. It is
essential before making connections to check the load against the
table above to ensure it meets the specifications of the dimmer.
CONTACT OUR FRIENDLY TEAM
Call: 0345 519 5858
Fax: 0845 519 5757
Email: sales@zanocontrols.co.uk
www.zanocontrols.co.uk
Zano Controls, Unit 1 Chantry Court, Wrythe Lane,
Carshalton, Surrey, SM5 2DG
Great British Design
For terms & conditions see www.zanocontrols.co.uk
For safety & certification info see www.zpatent.co.uk
Loading...