Zanker ZKB7328X, ZKB7328W, ZKB7328N User Manual
English
Important Safety Information
These warnings are provided in the interest of safety. You MUST read them carefully before installing or using the appliance.
During use
This appliance has been designed for cooking edible
foodstuff only and MUST NOT be used for any other
purposes.
Ensure that all control knobs are in the OFF position
when not in use.
Should you connect any electrical tool to a plug near
this cooking appliance, ensure that electric cables are
not in contact with it and keep them far enough from
the heated parts of this appliance.
If the appliance is out of order, disconnect it from the
electric supply.
Do not leave untensils containing foodstuffs, e. g. fat
or oil in or on the appliance. This could cause damage
in case the appliance is inadvertently switched on.
Always place the dripping pan in position to collect fat
when using the grill or when cooking meat. Pour a little
water into the dripping pan to avoid smoke and
unpleasant smells.
Always use oven gloves to remove pans from the oven.
For hygiene and safety reasons, this appliance should
be kept clean at all times. A build-up of fats or other
foodstuff could result in a fire.
Disconnect the appliance from the electrical supply,
before carrying out any cleaning or manteinance work.
Some parts of the appliance are covered by a shock-
proof plastic film. Remove this film before using the
oven.
This appliance is meant to operate with a single-
phased connection to 230V electrical supply. An
eventual 400V poliphasic connection without earth
wire will destroy the oven and the hob, if fitted.
The manufacturer disclaims any responsability
should all the safety measures not be carried out.
person, in accordance with existing rules and
regulations.
It is dangerous to alter the specification in any way.
Once you removed all packaging from the appliance,
ensure that it is not damaged and the electric cable is
in perfect conditions. Otherwise, contact your dealer
before proceeding with the installation.
Service
Under no circumstances should you attempt to repair
the appliance yourself. Repairs carried out by
unexperienced persons may cause injury or serious
malfunctioning. Refer to your local Service Centre.
Always insist on genuine spare parts.
Environmental Information
After installation, please dispose of the packaging with
due regard to safety and the environment.
When disposing of an old appliance, make it unusable,
by cutting off the cable.
It is most important that this instruction book
is be retained with the appliance for future
reference. Should the appliance be sold or
transferred, always ensure that the book is left
with the appliance in order that the new
owner can get to know the functions of the
appliance and the relevant warnings.
Child Safety
This appliance has been designed to be operated by
adults and children under supervision. Young children
MUST NOT be allowed to tamper with the controls or play
near or with the oven.
Accessible parts of this appliance may become hot
when it is in use. Children should be KEPT AWAY until it
has cooled.
Installation
It is mandatory that all operations required for the
installation are carried out by a qualified or competent
Guide to Use the instructions
The following symbols will be found in the text to guide
you throughout the Instructions:
Safety Instructions
Step by step instructions for an operation
F
Hints and Tips
Environmental information
43
Contents
For the User For the Installer
Important Safety Information 43
Description of the appliance 44
Using the Oven 45
Electronic programmer 46
Hints and Tips 48
Cooking Tables 49
Cleaning and Maintenance 51
Technical Assistance 52
Something not working... 52
Technical Data 53
Installation 53
Electrical Connection 54
This appliance complies with the following
E.E.C. Directives:
- 73/23 - 90/683 (Low Voltage Directive);
- 89/336
- 93/68 (General Directives)
and subsequent modifications.
MANUFACTURER: ELECTROLUX ZANUSSI S.p.A.
(Electromagnetical Compatibility Directive);
Viale Bologna, 298
47100 FORLÌ (Italy)
Description of the appliance
524
6 3
1. Control panel
1
7
2. Oven Function control knob
3. Electronic programmer
4. Oven Thermostat control knob
5. Overall control light
6. Oven thermostat control light
7. Oven lamp
44
Using the Oven
Oven function control knob (Fig. 1)
The oven function control knob can have the following
symbols and functions:
Oven Light - The oven light will be on without any
cooking function
Conventional cooking - The heat comes from both
the top and bottom element, ensuring even heating
inside the oven.
Top heating element - The heat comes from the top
of the oven only.
Bottom heating element - The heat comes from the
bottom of the oven only.
Inner grill element only - can be used for grilling
small quantities.
Double Grill - The full grill element will be on.
Thermal Grilling - This function offers an alternative
method of cooking food items, normally associated
with conventional grilling. The grill element and the
oven fan operate together, circulating hot air around
the food. When using this function, select a
maximum temperature of 200°C and do not
exceed 1 hour of operation.
Fan cooking - This allows you to roast or roast and
bake simoultaneously using any shelf, without
flavour transference.
Defrost Setting - This setting is intended to assist
in thawing of frozen food.
Thermostat control knob (Fig. 2)
Turn the thermostat control knob to select temperatures
between 50°C and 250°C (MAX).
Thermostat control light (°C)
Once the oven temperature has been selected, the
temperature light will come on and remain on until the
oven has reached the correct setting; after that, it will go
on and off with the thermostat, showing how the temperature is being maintained.
Oven control light
It will come on every time an heating element is set on
operation.and the oven will switch off automatically.
0
Fig. 1
FO2000
50
MAX
100
200
150
Fig. 2
FO 2153
When the oven is first installed
Before cooking for the first time, carefully wash
the oven accessories.
The oven will work only if the time of day has
been set (please read the instructions).
Once the oven has been installed:
F
a) set the thermostat knob to MAX (250);
b) switch the oven function control knob to conventional
cooking ( );
c) allow the oven to run empty for approximately 45
minutes;
d) open a window for ventilation.
During this time, an unpleasant odour may be emitted.
This is absolutely normal, and is caused by residues of
manufacturing.
Repeat this operation for the grill and fan cooking function.
Once this operation is carried out, let the oven cool down,
then clean the oven cavity with a soft cloth soaked in warm
soapy water.
FO 2161
The Safety Thermostat
This oven is provided with a safety thermostat. In case of
malfunctioning of the main thermostat, and consequent
over-heating, the safety device will stop the power supply
to the appliance. If this happens, call your local Service
Centre. Under no circumstances should you attempt to
repair the appliance yourself.
The Cooling Fan for the Controls
This oven is provided with a cooling fan, meant to keep the
front panel, the knobs and the oven door handle cool. This
fan may run on after the oven or grill is switched off, until
a normal temperature is reached.
Fig. 3
To open the oven door, always catch the
handle in its central part (Fig. 3).
45
Electronic programmer
4
5
6
Fig. 4
The oven will work only if the time of day has been set.
Moreover, the oven can also be operated without any programme.
23
1
7
8
FO 2571
1. Push button for selecting a function
2. Decreasing control button
3. Increasing control button
4. Display
5. Cooking Duration pilot lamp
6. End of cooking pilot lamp
7. Minute minder pilot lamp
8. Time of day pilot lamp
Setting the time of day
When the power supply is switched on, or after a power failure, the Time
of day pilot lamp will flash on the display.
To set the correct time of day:
1. press button or .
2. After the setting is carried out, wait for 5 seconds: the Time of day
pilot lamp will go out and the display will show the set time. The
appliance is ready for use.
To reset the correct time of day:
1. press button repeatedly to select the Time of day function. The
relevant pilot lamp will start flashing. Then proceed as described
above.
The time of day may be reset only if no automatic function (cook
duration or end of cooking ) has been set.
Cooking Duration function
Thanks to this function, the oven will automatically switch off at the end
of a programmed cooking duration time. Place food in the oven, select
a cooking function and adjust the cooking temperature. Press button
repeatedly to select the Cooking Duration function. The relevant pilot
lamp will start flashing. Then, proceed as follows:
To set the duration time:
1. press button or .
2. After the setting is carried out, wait for 5 seconds: the "Cooking
Duration" pilot lamp will come on and the display will revert to
the time of day.
3. When cooking time is over, the oven will be switched off automatically
and an acoustic alarm will be heard, while the pilot lamp will start
flashing. Turn the oven function and the thermostat control knob to
zero.
To switch off the acoustic alarm, press any button. NOTE: when
doing this operation, the oven will be operated again, therefore,
remember to turn the oven function and the thermostat control knob
to zero at the end of the cooking time.
To cancel the duration time:
1. Press button repeatedly to select the Cooking Duration function.
The relevant pilot lamp will flash and the display will show the
remaining cooking time.
2. Press button until the display shows 0:00. After 5 seconds
the pilot lamp will go out and the display will revert to the time of
day.
46
End of cooking function
Thanks to this function, you can set the oven to switch off automatically when a
programmed end of cooking time is over. Place food in the oven, select a cooking
function and adjust the cooking temperature. Press button repeatedly to select
the End of cooking function. The relevant pilot lamp will start flashing. Then,
proceed as follows:
To set the End of cooking time:
1. press button or .
2. After the setting is carried out, wait for 5 seconds: the End of cooking pilot
lamp will come on and the display will revert to the time of day.
3. When cooking time is over, the oven will be switched off automatically and an
acoustic alarm will be heard, while the pilot lamp will start flashing. Turn the
oven function and the thermostat control knob to zero.
To switch off the acoustic alarm, press any button. NOTE: when doing this
operation, the oven will be operated again, therefore, remember to turn the
oven function and the thermostat control knob to zero when cooking is over.
To cancel the End of cooking time:
1. Press button repeatedly to select the End of cooking function. The
relevant pilot lamp will flash and the display will show the programmed
End of cooking time.
2. Press button until the display shows the current time of day. The
programmer will beep and the pilot lamp will go out.
Cooking duration and End of cooking
time combined
The functions Cooking duration e End of cooking time can be used simultaneously
to set the oven to switch on and off automatically at a later time.
1. With the Cooking duration function (carry out the cooking duration setting
as described in the relevant chapter) set the duration time. Then, press button
: the display will show the programmed setting.
2. With the End of cooking time function (carry out the End of cooking
setting as described in the relevant chapter) set the end of cooking time.
The relevant pilot lamps will come on and the display will show the time of
day. The oven will switch on and off according to the set programmes.
Minute minder function
The minute minder alarm will sound at the end of a timed period, but THE OVEN
WILL REMAIN ON, if it is in use.
To set the minute minder:
1. Press button repeatedly to select the Minute minder function. The relevant
pilot lamp will start flashing.
2. Then, press button or (maximum: 2 hours, 30 minutes).
3. After the setting is carried out, wait for 5 seconds: the Minute minder pilot
lamp will come on.
4. At the end of the timed period, the pilot lamp will start flashing and acoustic
alarm will be heard. To switch off the acoustic alarm, press any button.
To cancel the minute minder:
1. Press button repeatedly to select the Minute minder function. The relevant
pilot lamp will flash and the display will show the remaining time.
2. Press button until the display shows 0:00. After 5 seconds the pilot
lamp will go out and the display will revert to the time of day.
How to switch off the display
1. Press two or three programmer push buttons simoultaneously and keep
them pressed for about 5 seconds. The display will switch off.
2. To switch on the display, press any button.
The display can be switched off only if no other functions have been
set.
47
Loading...