Zanker KDT10032FK User Manual [nl]

User Manual
Benutzerin‐
formation
Dishwasher
Geschirrspü‐
ler
KDT 10032FK

Contents

Daily use Hints and tips 12 Care and cleaning 13 Troubleshooting 14 Technical information 15
Subject to change without notice.

Safety information

Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible if an incorrect installation and use causes injuries and damages. Always keep the instructions with the appliance for future reference.

General Safety

This appliance is intended to be used in household and similar
applications such as:
farm houses; staff kitchen areas in shops, offices and other working
environments;
by clients in hotels, motels, bed & breakfast and other residential type
environments.
Do not change the specification of this appliance.
The operating water pressure (minimum and maximum) must be between
0.5 (0.05) / 8 (0.8) bar (Mpa)
Obey the maximum number of 13 place settings.
If the supply cord is damaged, it must be replaced by the manufacturer, its
Authorised Service Centre or similarly qualified persons in order to avoid a hazard.
Put knives and cutlery with sharp points in the cutlery basket with the
points down or in a horizontal position.
Do not keep the appliance door open without supervision to prevent to fall
on it.
Before maintenance, deactivate the appliance and disconnect the mains
plug from the mains socket.
Do not use water spray and steam to clean the appliance.
The ventilation openings in the base (if applicable) must not be obstructed
by a carpet.
9
2
The appliance is to be connected to the water mains using the new
supplied hose-sets. Old hose sets must not be reused.

Children and vulnerable people safety

This appliance can be used by children aged from 8 years and above and
persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
Do not let children play with the appliance.
Keep all detergents away from children.
Keep children and pets away from the appliance door when it is open.
Cleaning and user maintenance shall not be made by children without
supervision.

Safety instructions

Installation

• Remove all the packaging.
• Do not install or use a damaged appliance.
• Do not install or use the appliance where the temperature is less than 0 °C.
• Obey the installation instruction supplied with the appliance.

Electrical connection

Warning! Risk of fire and electrical
shock.
• The appliance must be earthed.
• Make sure that the electrical information on the rating plate agrees with the power supply. If not, contact an electrician.
• Always use a correctly installed shockproof socket.
• Do not use multi-plug adapters and extension cables.
• Make sure not to cause damage to the mains plug and to the mains cable. Should the mains cable need to be replaced, this must be carried out by our Authorised Service Centre.
• Connect the mains plug to the mains socket only at the end of the installation. Make sure that there is access to the mains plug after the installation.
• Do not pull the mains cable to disconnect the appliance. Always pull the mains plug.
• This appliance complies with the E.E.C. Directives.
• Only for UK and Ireland. The appliance has a 13 amp mains plug. If it is necessary to change the fuse in the mains plug, use fuse: 13 amp ASTA (BS
1362).

Water connection

• Make sure not to cause damage to the water hoses.
• Before you connect the appliance to new pipes or pipes not used for a long time, let the water flow until it is clean.
• The first time you use the appliance, make sure that there is no leakage.
• The water inlet hose has a safety valve and a sheath with an inner mains cable.
Warning! Dangerous voltage.
• If the water inlet hose is damaged, immediately disconnect the mains plug from the mains socket. Contact the Authorised Service Centre to replace the water inlet hose.
3
Use
1
2
3
4
• Do not sit or stand on the open door.
• Dishwasher detergents are dangerous. Obey the safety instructions on the detergent packaging.
• Do not drink and play with the water in the appliance.
• Do not remove the dishes from the appliance until the programme is completed. There can be detergent on the dishes.
• The appliance can release hot steam if you open the door while a programme operates.
• Do not put flammable products or items that are wet with flammable products in, near or on the appliance.

Service

• Contact the Authorised Service Centre to repair the appliance. We recommend only the use of original spare parts.

Control panel

• When you contact the Authorised Service Centre, ensure that you have the following information that is available on the rating plate. Model : PNC : Serial Number :

Disposal

Warning! Risk of injury or suffocation.
• Disconnect the appliance from the mains supply.
• Cut off the mains cable and discard it.
• Remove the door catch to prevent children and pets to get closed in the appliance.
On/off button
1
Programme buttons
2
Delay button
3

Indicators

4
Indicators
4
End indicator. Multitab indicator. Salt indicator. It is always off while the programme operates. Rinse aid indicator. It is always off while the programme operates.

Programmes

Programme Degree of soil
Type of load
2)
3)
4)
1) The pressure and the temperature of the water, the variations of the mains supply, the options and the quantity of dishes
can change the values.
2) With this programme you have the most efficient use of water and energy consumption for crockery and cutlery with nor­mal soil. (This is the standard programme for test institutes).
3) With this programme you can wash a load with fresh soil. It gives good washing results in a short time.
4) Use this programme to quickly rinse the dishes. This prevents the remaining food to bond on the dishes and bad odours to
come out from the appliance. Do not use detergent with this programme.
Normal soil Crockery and cut­lery
Normal soil Crockery and cut­lery
Heavy soil Crockery, cutlery, pots and pans
Fresh soil Crockery and cut­lery
All
Programme phases Consumption values
1)
• Prewash
• Wash 50 °C
• Rinses
• Dry
• Prewash
• Wash 65 °C
• Rinses
• Dry
• Prewash
• Wash 70 °C
• Rinses
• Dry
• Wash 60 °C
• Rinse
• Prewash
Duration
(min)
225 0.932 10.2
150 1.4 14
144 - 154 1.3 - 1.5 12.5 - 14.5
30 0.9 10
14 0.1 4
Energy
(kWh)
Water
(l)

Settings

Programme selection mode

The appliance is in programme selection mode when only the indicator of the programme is on. When the appliance is in programme selection mode, it is possible to set a programme and to enter the user mode. If the control panel does not show this condition, do the RESET function.
5

RESET function

5x
6x
Press and hold simultaneously and until the appliance is in programme selection mode. With this function you can cancel the running programme or the delay start.

User mode

Press and hold simultaneously and until the indicators , , and start to flash. In user mode can be changed:
• The level of the water softener according to the water hardness.
• The activation or the deactivation of the acoustic signal for end of programme.
• The deactivation of the rinse aid dispenser when you want to use the Multitab option without rinse aid.
• The level of rinse aid according to the required dosage. These settings will be saved until you change them again.

Adjusting the water softener

While the appliance is in user mode:
1. Press
• The indicators
• The indicator continues to flash.
• The indicator starts to flash. The number of flashes indicates the level (E.g. 5 flashes + pause + 5 flashes = level 5).
6
.
, and go off.
2. Press to change the setting. Each time you press the button, the level number increases. After level 10
4x
5x
you will start again from level 1.
3. Press the on/off button to confirm the setting.

The water hardness table

German degrees
(°dH)
47 -50 84 - 90 8.4 - 9.0 58 - 63 10
43 - 46 76 - 83 7.6 - 8.3 53 - 57 9
37 - 42 65 - 75 6.5 - 7.5 46 - 52 8
29 - 36 51 - 64 5.1 - 6.4 36 - 45 7
23 - 28 40 - 50 4.0 - 5.0 28 - 35 6
19 - 22 33 - 39 3.3 - 3.9 23 - 27
15 - 18 26 - 32 2.6 - 3.2 18 - 22 4
11 - 14 19 - 25 1.9 - 2.5 13 - 17 3
4 - 10 7 - 18 0.7 - 1.8 5 - 12 2
<4 <7 <0.7 < 5
1) Factory setting
2) Do not use salt at this level.
French degrees
(°fH)
mmol/l Clarke degrees Water softener lev-

Adjusting the rinse aid level

el
1)
5
2)
1
You can set the released quantity of rinse aid between level 1 (minimum quantity) and level 6 (maximum quantity). Level 0 will deactivated and no rinse aid will be released. Factory setting: level 4. While the appliance is in user mode:
1. Press
.
• The indicators , and go off.
• The indicator
continues to flash.
• The indicator starts to flash. The number of flashes indicates the current setting (e.g. 4 flashes + pause + 4 flashes = level 4)
2. Press to change the setting.
3. Press the on/off button to confirm the setting.
7

Deactivating the rinse aid dispenser

While the appliance is in user mode:
1. Press .
• The indicators , and go off.
• The indicator continues to flash.
• The indicator
2. Press to change the setting. The indicator off = Rinse aid dispenser deactivated.
The rinse aid indicator goes off.
3. Press the on/off button to confirm the setting.
indicates the current setting: the indicator on = Rinse aid dispenser activated.

Activating the acoustic signal for the end of programme

By default this acoustic signal is deactivated but it is possible to activate it. While the appliance is in user mode:
1. Press
• The indicators
• The indicator continues to flash.
• The indicator indicates the current setting: the indicator off = Acoustic signal off.
2. Press to change the setting. The indicator on = Acoustic signal on.
3. Press the on/off button to confirm the setting.
.
, and go off.

Before first use

1. Make sure that the current level of the water softener agrees with the hardness of the water
8
supply. If not, adjust the level of the water
A
softener.
2. Fill the salt container.
3. Fill the rinse aid dispenser.
4. Open the water tap.
5. Start a programme to remove any processing
residuals that can still be inside the appliance. Do not use detergent and do not load the baskets.
When you start a programme, the appliance can take up to 5 minutes to recharge the resin in the water softener. It seems that the appliance is not working. The washing phase starts only after this procedure is completed. The procedure will be repeated periodically.

Adding salt

Before first use put one litre of water in the salt container. Water and salt can come out from the salt container when you fill it. Risk of corrosion. To prevent it, after you fill the
salt container, start a programme.

Adding rinse aid

The rinse aid helps to dry dishes without streaks ans stains. It is automatically released during the hot rinse phase.
• Fill the rinse aid dispenser until the rinse aid dispenser reaches the marking "MAX".
• Remove the spilled rinse aid with an absorbent cloth to prevent too much foam.
• Fill the rinse aid dispenser when the indicator (A) becomes clear.

Daily use

1. Open the water tap.
2. Press the on/off button to activate the appliance.
Make sure that the appliance is in programme selection mode.
• If the salt indicator is on, fill the salt container.
• If the rinse aid indicator is on, fill the rinse aid dispenser.
3. Load the baskets.
4. Add the detergent. If you use multi-tablets, activate
the option Multitab.
5. Set and start the correct programme for the type of
load and the degree of soil.
9

Adding detergent

30
2
1
30
30
2
1
30
If the programme has a prewash phase, put a small quantity of detergent on the inner part of the appliance door.

Adding MULTI-TABLETS

The AUTO OFF function

This function decreases energy consumption by deactivating automatically the appliance when it is not operating. The function comes into operation:
• 5 minutes after the completion of the programme.
• After 5 minutes if the programme has not started.

Starting a programme

1. Keep the appliance door ajar.
2. Press the on/off button to activate the appliance. Make sure that the appliance is in programme selection mode.
3. Press the button related to the programme you want to start. The related programme indicator comes on.
4. Close the appliance door to start the programme.
10

Option delay

1. Set the programme.
2. Press again and again until the indicator related to the number of hours want to set comes on (3 o 6). The
delay indicator comes on.
3. Close the appliance door to start the countdown. When the countdown is completed, the programme starts.

Option Multitab

1. Set the programme.
2. Press and hold simultaneously and until the indicator comes on.
Activate this option when you use multi-tablets that integrate the salt, rinse aid and detergent functions. They can also contain other cleaning or rinsing agents.
This option deactivates the release of salt. The salt indicator does not come on. With the use of this option the programme duration is prolonged to increase the cleaning and drying results with the
use of multi-tablets.

Opening the door while the appliance operates

If you open the door while a programme is running, the appliance stops. When you close the door, the appliance continues from the point of interruption.

End of the programme

11
Loading...
+ 25 hidden pages