Power AmpTM 3
Instructions
*WARRANTY REGISTRATION
Your ZAGG Power AmpTM 3 comes with a one-year manufacturer’s warranty. In order to activate the warranty,
you must register your Power Amp 3 as well as keep your purchase receipt. If you purchased your Power
Amp 3 from Zagg.com, Zagg has already registered it and has a copy of your proof of purchase.
NEED MORE HELP? PLEASE SEE OUR FAQ SECTION AT: www.zagg.com/faq
INTRODUCTION
With your new Power Amp 3, you’re ready to stay connected to your world on all
your adventures. Just read and follow these instructions, pop your Power Amp 3
into your pocket, purse, or bag, and go with the power to prevent your phone
battery from ever dying again. Keep these instructions for future use.
CHARGING YOUR DEVICES
Your Power Amp 3 carries enough power to give your phone at least 1+ charge
(14 hours) of additional talk time*. In addition, it allows for pass-through charging
that lets you power your devices even while it’s plugged in. To keep your phone
from dying:
1. Connect the USB end of your charging cable to the outlet on the
Power Amp 3.
2. Connect the other end of your charging cable to the device you want to
charge — the Power Amp 3 will automatically begin charging it.
3. Continue on your activity until your device is charged to your liking and
then disconnect the charging cable.
4. Recharge your Power Amp 3.
*14 Hours additional talk time based on a 1800mAh battery.
CHARGING YOUR POWER AMP 3
Your Power Amp 3 comes charged and ready to go; but here’s how to recharge it
when you need to:
1. Connect the included micro USB charging cable to the micro USB
port on your Power Amp 3.
2. Connect the USB end of the included cable to your preferred 5V USB
outlet. Note: Do not leave your Power Amp 3 plugged into a wall
charger for extended periods of time. Doing so will diminish its
long-term performance.
3. The LED under the flashlight will light and flash according to its
current battery level. This indicates your Power Amp 3 is charging.
4. Wait for the battery indicator lights to turn off, indicating your Power
Amp 3 is fully charged.
5. Disconnect the charging cable and enjoy 3000mAh of simple,
portable power.
1 USB Port
Micro USB charging port
LED Flashlight
USING THE FLASHLIGHT
Your Power Amp 3 has a bright LED flashlight that’s ideal for lighting any situation.
To enjoy the flashlight feature:
1. Press the flashlight button to turn the flashlight on.
2. Press the flashlight button again to turn the flashlight off.
Note: The LED flashlight will automatically turn off after 10 minutes. Using the
flashlight does not significantly decrease the Power Amp 3’s stored power.
CHECKING THE BATTERY LEVEL
Your Power Amp 3 carries 3000mAh of power to help make sure your battery never
dies again. To check how much power it still carries:
1. Press the battery button. The LEDs under the flashlight will light one
of four ways:
a. Four lights indicate 75% power or more remaining.
b. Three lights indicate between 50-74% power remaining.
c. Two lights indicate between 25-49% power remaining.
d. One light indicates less than 24% power remaining.
2. Recharge your Power Amp 3 whenever you wish.
POWER SAVING TIP
Don’t leave your charging cable plugged into your Power Amp for extended
periods of time. Remove your cable when you’re done charging to preserve
more portable battery power.
For more help, please see our FAQ at: www.zagg.com/faq
To reach a trained customer service representative, please use one of the following:
zagg.com/support/contact.php
questions@zagg.com
1-800-700-ZAGG [9244]
00-1-801-839-3906 for international customers
©2015 ZAGG Inc | All Rights Reserved
NASDAQ: ZAGG | MADE IN CHINA
ZAGG and Power Amp are registered trademarks of ZAGG Intellectual Property Holding Co., Inc.
Changes or modifications not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Loading...