2.0 ABOUT THE MANUAL ..................................................................................................................................4
3.0 PARTS LIST ......................................................................................................................................................4
3.1 INCLUDED PARTS ....................................................................................................................................4
4.0 FEATURES .......................................................................................................................................................6
6.0 SYSTEM CONNECTIONS...............................................................................................................................8
6.1 PC SETUP ...................................................................................................................................................8
6.2 WEB SERVER - ENCODER ......................................................................................................................8
6.3 LOCAL IP SETTINGS – ENCODER ........................................................................................................9
10.1 WEB PAGE ...............................................................................................................................................15
Z3 Technology, LLC ♦ 100 N 8th ST, STE 250 ♦ Lincoln, NE 68508-1369 U.S.A. ♦ +1.402.323.07
V1.04.16
4
1.0 GENERAL INFORMATION
1.1 PREFACE
The Z3-MVE-02 Multi-Format Video Encoder is a compact 114mm x 203mm system that supports H.264 High
Profile encode up to 1080p at 30 frames per second. This solution works in multiple applications, such as low
cost broadcast encoders, low bandwidth video security, satellite uplink, remote monitoring and industrial
applications. The Z3-MVE-02 provides immediate access to multi-format HD video, integrated system
peripherals and production-qualified codecs.
The Z3-MVE-02 offers multi-format, multi-channel HD video up to 1080p30. The Z3-MVE-02 features HD
performance, compact size, and low latency while having less power consumption than a PC-based encoder
platform.
2.0 ABOUT THE MANUAL
Before attempting to connect or operate this product, please read these instructions carefully and save this
manual for future use.
Z3 Technology, LLC ♦ 100 N 8th ST, STE 250 ♦ Lincoln, NE 68508-1369 U.S.A. ♦ +1.402.323.07
V1.04.16
6
4.0 FEATURES
The Z3-MVE-02 is a high definition, low cost, network-enabled media encoder with the following features:
HD resolutions up to 1920x1080 including 1080i, 1080p30 and 720p
Supported video includes H.264, MPEG-4, and MPEG-2
Standard Definition encoding for ISDB-T, DVB-H, ...etc.
Low latency encode mode
Video Inputs: Composite, Component, HD-SDI, DVI, HDMI (Optional ASI input)
Input video re-sizer supports 1/2, 2/3 and 3/4 of standard resolutions
Output Interfaces: Ethernet and ASI (Optional HD-SDI output)
Outputs RTP or MPEG-2 Transport Stream
USB interface for mass storage devices or other peripherals
SD Card interface for local storage and firmware updates
RS232 serial port for configuration and control
Z3 Technology, LLC ♦ 100 N 8th ST, STE 250 ♦ Lincoln, NE 68508-1369 U.S.A. ♦ +1.402.323.07
V1.04.16
8
Microsoft Windows users
1. Go to the Start Menu and select
Control Panel
2. Click on Network and Sharing Center
3. Click on View Status
4. Click on Properties.
5. Click Internet Protocol (TCP/IP) and
click Properties.
6. In the Internet Protocol (TCP/IP)
Properties window, select "Use the
following IP address" if not already
selected and specify the IP address
you wish to use. While entering this
data you'll also need to specify the
subnet mask and default gateway.
Linux users
The below information is for how to specify
and adjust your network settings through the
command prompt. Changing your network
settings will require root access.
1. Get to the command prompt.
2. Move to the /etc/sysconfig/network
directory.
3. Edit the interfaces file and adjust your
network settings in this file.
6.0 SYSTEM CONNECTIONS
The System can be controlled via the Web Server on the Z3-MVE-02. It can also be controlled via the serial
port.
6.1 PC SETUP
Initially, the simplest way to setup the networked PC to communicate with the Z3-MVE-02 is to put the
PC on the same subnet as the Z3-MVE-02. The IP address of the Z3-MVE-02 can be found on the bottom side
of the Z3-MVE-02. The Windows PC can be setup on the same subnet by using these parameters:
NOTE: The static IP of the computer cannot be the same as the static IP of the
Z3 Technology, LLC ♦ 100 N 8th ST, STE 250 ♦ Lincoln, NE 68508-1369 U.S.A. ♦ +1.402.323.07
V1.04.16
12
Input Selection
Input Interface
Ethernet, DVB-ASI
Input Format
RTP, MPEG-2 TS
RTP IP: Port
Custom
Decoder Setup
Video Codec
H.264
Audio Codec
AAC, PCM, None
Output Setup
Output Interface
SDI
Video Frame Rate
50Hz, 60Hz
Local IP Setup
Local IP Address
192.168.X.XX
Local Netmask
255.255.0.0
Default Gateway
192.168.0.XX
6.6 IP SETTINGS – DECODER
1. Once the decoder has stopped, type in your desired IP settings
2. Hit “Save User” to save your desired settings
3. Power cycle the Z3-MVPR-01
4.The new IP settings will now take effect
6.7 DECODER CONFIGURATION OPTIONS
7.0 STREAMING OPERATION
After connecting your video/audio source and configuring the Z3-MVE-02 Encoder, hit “Start Encoder” so the
status below says “Status: Running.” If you are using the serial command instead, type “S” to start streaming.
The way to set up VLC as your stream receiver on your PC differs depending on the format of your output
stream.
If your output format is transport stream, please follow the steps below:
Z3 Technology, LLC ♦ 100 N 8th ST, STE 250 ♦ Lincoln, NE 68508-1369 U.S.A. ♦ +1.402.323.07
V1.04.16
13
7.1 TRANSPORT STREAM
1. Open VLC Media Player
2. On the Media menu choose “Open Network Stream” (Cntrl + N)
3. If using VLC version 1.0.X:
a. On the Protocol menu choose “UDP”
b. Type in the static IP address of your personal PC
c. Change the Port Address to “8888”
4. If using VLC version 1.1.X:
a. Enter the network URL as follows: udp://@xxx.xxx.xxx.xxx:8888 (where xxx.xxx.xxx.xxx is the IP
Address of your personal PC)
5. Press play
6. If the original video is interlaced, the video can be deinterlaced as follows:
a. On the Video Menu, choose “Deinterlace” and choose an option other than “Disable”
If your output format is real-time transport protocol, please follow the steps below:
7.2 REAL-TIME TRANSPORT PROTOCOL
1. Open VLC Media Player
2. On the Media menu choose “Open File” (Cntrl + O)
3. Under the Media Files category, choose “All Files (*)”
4. Choose the SDP file provided by Z3 Technology
- Note: If you do not have the SDP file, please to refer to your Z3 Server user account and download
the file.
5. If the original video is interlaced, the video can be deinterlaced as follows:
a. On the Video Menu, choose “Deinterlace” and choose an option other than “Disable”
8.0 DYNAMIC BIT-RATE & FRAME-RATE CHANGE
The dynamic bit-rate and frame-rate control will take effect, if you change *only* the following parameters:
Video Bit Rate
Frame Decimation
After the Video Bit Rate and Frame Decimation rate have been configured to your preferred settings, hit the
"Start Encoder" or "Restart Encoder" button.
The web page will respond with:
Status: Changed rate
The video stream will continue uninterrupted with the new parameter.
Z3 Technology, LLC ♦ 100 N 8th ST, STE 250 ♦ Lincoln, NE 68508-1369 U.S.A. ♦ +1.402.323.07
V1.04.16
14
9.0 APPENDIX A: SERIAL CONTROL
Note: Please only use the serial control if you are experiencing difficulties with the Web
Server.
Plug-in a DB-9 serial cable from the Z3-MVE-02 to your PC
Set up Teraterm on the PC for 115k, 8, N, 1, N, 1ms/char, 50ms/line
Connect to the proper COM port
Connect the Power to the Z3-MVE-02
Power-on the Z3-MVE-02
Output should come immediately to the Teraterm console
| Current
| I - Change video input COMPONENT
| A - Change audio aac
| N - Change network address 225.1.2.3
| T - Change transport RTP
| F - Change framerate divider 1
| R - Change resolution 1080I
| G - Change GOP size 60
| B - Change video bitrate 9000k
| P - Change H.264 Profile high
| Y - Change H.264 QP range 5, 28, 51,0,40
| C - Change rate control mode CBR
| E - Change scan mode Interlaced
| D - Change delay limit ms 500
+------------------------------------------------------------------------------------------------+
| 1 - Set defaults for D1 streaming
| 2 - Set defaults for 720p streaming
| 3 - Set defaults for 1080I streaming
|
| S - Start streaming
| X - eXit to prompt
| W - Write config to flash
+=========================================================+
Enter option:
Z3 Technology, LLC ♦ 100 N 8th ST, STE 250 ♦ Lincoln, NE 68508-1369 U.S.A. ♦ +1.402.323.07
V1.04.16
16
- Power cycle system for clean boot and system should be updated.
10.2 SD CARD
- Locate the UPD-z3-mve02-v1.04.15.img file on your Z3 Server user account
- Place SD card into computer
- Open the zwriter.exe windows program (provided by Z3)
- Select the UPD-z3-mve02-v1.04.15.img file
- Select correct location for your SD card Do NOT make mistake on this item. This will cause wherever
you are writing to be overwritten. There is no recovery once you hit “Write Device”
- Eject SD card from computer
- Place in SD card socket of APP board
- Power on system with terminal output connected to PC
- You will see the system updating the flash
- Once complete, the system will boot.
- Power off unit
- Remove SD card
- Power cycle system for clean boot and system should be updated.
11.0 TROUBLESHOOTING
No video is usually caused by networking issues.
o First: check IP address and Netmask. Ping PC from Z3-MVE-02 and ping Z3-MVE-02 from PC. Use
direct connection from Z3-MVE-02 to PC without router/customer network. Once video connection
is established, then add in customer specific network equipment.
o Second: check to make sure firewalls are turned off
o Third: check video source. Verify video source is outputting compatible analog video
o Fourth: verify PC is fast enough and has enough DDR to decode compressed video
o Fifth: verify VLC version is 1.1x or later