YUNJI INTELLIGENT TECHNOLOGY W5 User Manual

OUKITEL W5

User Manual for Smart Watch

I. Method of Application

1. Use of Watch

(1) Boot: When the watch is powered off, press and hold on the touch key for 3 seconds to boot
(If there is a side key, press and hold on the side key for 3 seconds to boot), showing the boot
animation and vibrating, then displaying the main interface of time of the watch as shown in Figure
1-1-1. The display duration can be adjusted in the APP.

(2) Operation: With a single point of touch on the area, the screen interface can be switched. If
the current interface has its sub-interface, then press and hold on the touch area for three seconds
to enter the corresponding sub-interface, (If the watch has the side key, press and hold on the side

key for three seconds to power off in random interface and press the side key for once to return to
the time display interface in terms of other interfaces.)

(3) Shutdown: Switch to the shutdown interface of the watch as shown in Figure 1-1-2, press
and hold on the touch key for three seconds, showing the shutdown animation and vibrating, then
powering off (if there is the side key, press and hold on it to power off in random interface).

(Fig. 1-1-1) (Fig. 1-1-2)

2. Bluetooth connection/ disconnection

(1) APP download: Search for "H Band" in the application market (for Android) or APP store (for
Apple) to download and install, or scan the QR code below to download the "H band" application.

(2) Switch on the mobile Bluetooth→ open the "H band" application→ " Click to connect
device", search for the watch Bluetooth necessary for connection and bond with the device. With
operating steps above, the watch can be connected with the mobile APP and can be set in the APP
after connection.

(3) Disconnection:
Method 1: Open the "H Band"→ "DISCONNECT"→disconnection (for IOS, it's necessary to ignore
the device in the mobile Bluetooth setting for the disconnection)
Method 2: Direct turnoff of mobile Bluetooth

3. Charging

(1) Charging: When charged in shutdown mode, the watch will power on automatically, show

the main interface and flash the battery icon in the main interface. However, the users can only
singly touch to display the main interface during charging and perform no other operations. In
addition, when the watch is shaken during charging, the charging animation will appear as shown in
Figure 1-3-2 and the dark screen will be shown after 8 seconds. When the battery is fully charged,
the flash in the interface will keep bright without blinking.

(Fig. 1-3-1) (Fig. 1-3-2)

4. Firmware Update

When there is a new version of update for the applications in the watch device, the firmware
update will be prompted when connecting with APP.

5. Restore Factory Settings

Users can clear watch data and restore watch factory settings and the methods are as follows:
Open the "H-Band"--> Device connection--> My Device--> Resetting Device Password--> Clearing
Data. All data of watch will be cleared after the operation above and all function switches will be set
as the default.

II. Function Introduction and Operation Instructions

1. Common Functions

1.1 Sports Mode

(1) Function Introduction

a. In the sports mode, the watch can record the time, heart rate, calorie and steps during sports
and to pause and to continue can be selected midway.

b. Automatic exit: During sports. the watch will automatically judge the motion state of the users.
If the watch has determined the current consistence with the conditions of sports exit, and then it will
exit the sports mode automatically.

c. Data storage: The watch only saves the latest 3 sports data

(Fig. 2-1-1) (Fig. 2-1-2) (Fig. 2-1-3) (Fig. 2-1-4) (Fig. 2-1-5)

1.2 Step-counting, Calorie and Mileage

(1) Function Introduction: The watch will display the users' total number of steps, calories,
mileage of the day and the completion of sports goals in the interface and erase the data at 00:00