Yuneec Technology E90 User Manual

E90 User Manual

OPERATING INSTRUCTIONS:

Insert the gimbal connection cord to the inner side of gimbal damping plate (relative

(1)

to the direction of H520 gimbal connection port).

Mount the gimbal thumb screws and rubber lock washers (4 pcs) to the gimbal and

(2)

rotate the screws until they’re secured into the gimbal damping plate.

(3)

Connect the gimbal power cord to H520 gimbal connection port.

ELECTRICAL PARAMETERS:

Working Current: 0.4A
Input/Operating Voltage: 17V
Image Sensor: 1'' CMOS sensor
Electronic Shutter: 8s‐‐‐1/8000s
FrequencyRange:

To Take A St i l l P h oto

Press the button located near the bottom left corner of the transmitter. You'll hear an
audible 'shutter' sound from the transmitter and the LED indicator on the front of the
E90 will blink blue and green alternatively once. It will take approximately 1‐2 seconds to
capture the photo and before you can take another still photo.

To START/STOP Recording Video

Press the button located near the bottom right corner of the transmitter. You'll hear an
audible indication from the transmitter each time the recording starts/stops. And while
video is recording the LED indicator on the front of the CGO3+ will flash blue and green,
and there will be a red dot next to the time length of the recording on the screen of the
transmitter.

1. FCC STATEMENT:

This equipment has been tested and found to comply with the limits for Part 15 of the
FCC rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment to an outlet on a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any
interference

5725

‐

5850

MHz

received, including interference that may cause undesired operation.
—Consult the dealer or an experienced radio/TV technician for help.

The user manual or instruction manual for an intentional or unintentional radiator shall
caution the user that changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the equipment. In
cases where the manual is provided only in a form other than paper, such as on a computer
disk or over the Internet, the information required by this section may be included in the
manual in that alternative form, provided the user can reasonably be expected to have the
capability to access information in that form.

2. RF EXPOSURE WARNING

• This equipment must be installed and operated in accordance with provided
instructions and the antenna(s) used for this transmitter must be installed to provide a
separation distance of at least 20 cm from all persons and must not be co‐located or
operating in conjunction with any other antenna or transmitter. End‐users and installers
must be provide with antenna installation instructions and transmitter operating
conditions for satisfying RF exposure compliance.

3. IC RADIATION EXPOSURE STATEMENT FOR CANADA

This device complies with Industry Canada licence‐exempt RSS standard(s).Operation is
subject to the following two conditions: (1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause
undesired operation of the device.Le présent appareil est conforme aux CNR d'Industrie
Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée
aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2)
l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d'en compromettre le fonctionnement.
This equipment complies with IC RSS‐102 radiation exposure limit set forth for an
uncontrolled environment.Cet équipement respecte les limites d'exposition aux
rayonnements IC définies pour un environnement non contrôlé

This equipment should be installed and operated with minimum distance 20cm between the
radiator and your body.

Installation et mise en œuvre de ce matériel devrait avec échangeur distance minimale entre

20 cm et ton corps.

Manufacturer:

Yuneec International (China) Co., Ltd.
Production Address:
No.388 East Zhengwei Road, Jinxi Town, Kunshan, Jiangsu 215324, China

Distributor:
CN: Youyu (Shanghai) Digital Technology Co.,Ltd.

Address: B 15F, 461 HongCao Road,CaoHeJing Software Building XuHui District, Shanghai,

China

Tel.: [phone]

US: Yuneec USA Inc.

Address: 5555 Ontario Mills Parkway, Ontario, CA91764, USA
Tel.: [phone]

EU: Yuneec Europe GmbH

Address: Niklaus–Otto‐Strasse 4, 24568 Kaltenkirchen, Germany.
Tel.: [phone]

COLLECTION AND PROCESSING OF DATA

Yuneec may collect navigation information such as GPS data to help improve our
products. We may also collect Depth Map information and Infrared Image information
from your drone delivered to our service center for repair and maintenance service or
any other service. We may also collect other information such as device information,
server log information, etc. We may also collect personal information used in registration
if you choose to become a registered user and any other information user provided to
Yuneec.
We may also collect information which user send to other users, and the recipients and
senders of such information. We reserve the right to disclose your information if
required to do so by law or in the good‐faith belief that such disclosure is needed to
comply with applicable laws, for example in response to a court order, judicial subpoena,
warrant or request from government, or otherwise cooperating with government
agencies or law enforcement. We also reserve the right to disclose your information that
we believe in good faith is necessary or appropriate to: (i) protect ourselves or others
from fraudulent, unlawful, or abusive activities; (ii) take precautions against potential
liability; (iii) protect the security of the Yuneec Apps embedded into or downloaded onto
your drone or any associated equipment and services; (iv) protect the legal rights of
ourselves or any others. Any information we collected maybe disclosed or transferred to
an acquirer, successor or assignee as part of any potential merger, acquisition, debt
financing or other activities that involves transfer of business assets. We may make the
aggregated non‐personal information of the users available to third parties for various
purposes, including (i) complying with various report obligations; (ii) marketing efforts;
(iii) analyzing product safety; (iv) understanding and analyzing our users ’ interests,
habits, usage pattern for certain functionalities, services, content, etc.