Yujin robot YCR-M05 User Manual

www.yujinrobotusa.com

eX500 care & maintenance

1. Regularly empty the dust bin and replace the antibacterial filter

2. Cleaning the main brush

YCR-M05

Quick Start Guide

Robotic Vacuum Cleaner eX500

Furrow

3. Display window error messages & solutions

Check

display

C 1

C 2

C 3

C 4

C 5

C 6

C 7

C 8

Lifted wheel

Cannot detect floor

Dust bin error

Wheel motor overload

Brush motor overload

Suction motor overload

Internal system error

Magnetic Sensor

Cause Solution

Move eX500 to a flat area.

Move eX500 to a flat area in case the wheel was stuck on a
obstacle.

Dust bin is not properly assembled or installed.

Check if a foreign material such as hair or lint is caught in the wheel
and remove the material.

Check if a foreign material such as hair or lint is caught in the main
brush or side brush and remove the material.

Clean filter, empty the dust bin.

Turn off the power switch of the robot cleaner then turn it on again.

Check that the front wheel and magnetic sensor are clean and
correctly installed.

CLICK

iAQG.USA.500.V1

■The complete user manual is also available to download on our website

www.yujinrobotusa.com

www.yujinrobotusa.com

Installing eX500

1. Preparation of the robotic vacuum cleaner

Entrance
prevention tape

2. Installing the Charging Station and start charging

Using eX500

1. Changing vacuum modes

StartMethod

Bottom
side

Changing cleaning mode

3. Setting a scheduled cleaning

※ eX500 starts cleaning at the set time every day, completes a cleaning cycle, and then returns to the charging station.

On Device

Remote
control

1) Before setting a scheduled cleaning’

Display

Window

MODE

CLOCK TIMER

MAX

Setting the TIMER

Set "hour" Set "minute"

s start time, make sure to set the clock with the current time.

(Remote control is required to set the time)

2) For timer cleaning, use +/- buttons to set“hour”and press Enter button and use +/- buttons to set“minutes”
and press Enter button. Once the time setting completes, select the cleaning mode and press Enter button.

To check the start time: press the TIMER button once.

※

To cancel the set time: press the TIMER button twice.

Climbing mode

※ CLIMB is set
MAX or SPOT cleaning. When CLIMB is set eX500 can cross obstacles up to 0.79 inches in height. Sometimes the
shape of a surface of an obstacle may prevent the robot from climbing over it even when it is less than 0.79 inches in height.

※ Deselect CLIMB when circumstances require cleaning without climbing over obstacles of 0.2 inches or higher that need to
be avoided (shag rug for example). eX500 will always climb over obstacles up to 0.2 inches in height

※ Note: SPOT and MAX modes are only available via the remote control.

Set the

mode with

Remote

control

& iClebo

“on” by default but can be deselected on the remote control in AUTO or RANDOM modes and also within

Cleaning

mode

Explanation Explanation

AUTO is the default cleaning
mode that uses Smart
Navigation to move in a
systematic cleaning pattern
to cover the entire cleaning
area.

Cleaning

mode

RANDOM cleans for a set time (60 min. by default).
In RANDOM mode eX500 often covers areas
one or more times increasing the quality of the
cleaning. After selecting RANDOM mode use the
+/- buttons on the remote control to set the
cleaning duration.

Remote
control

eX500

MODE

CLOCK TIMER

MAX

2. Setting the current time

On Device

Remote
control

Display

Window

MODE

CLOCK TIMER

MAX

Setting the time

Set "hour" Set "minute"

① Press the“Clock”button on the remote control.
② Use the +/- buttons to set the hour, then press“Enter”
③ Use the +/- buttons to set the minute, then press“Enter”
④ The iClebo will confirm the time is set with a beep.
⑤ Press the set button when correct time is displayed.

(Remote control is required to set the time)

.

In MAX cleaning mode the iClebo first operates in

Only with

the

remote

control

eX500 cleans within
a range of 1.6 ㎡ with a
zigzag pattern.

AUTO mode where it uses its camera to
systematically navigate the entire accessible
area. After that eX500 enters RANDOM mode
and continues cleaning until the battery runs low
making sure you will be happy with its double
cleaning job.

Status StatusExplanation Explanation

This cleaning mode is automatically
entered once the mop plate is mounted
on the bottom of eX500. It is
recommended that CLIMB mode be
deselected when in mopping mode.

.

※ If you wish to clean without eX500 climbing over obstacles of 0.20 inches or higher such as rugs or doorsills, deselect

By using the CLIMB function the iClebo’
ability will be increased from 0.20 inches to cross
obstacles up to a height of about 0.79 inches.
Sometimes the shape of the surface of an obstacle
may prevent eX500 from climbing over it even
when the obstacle is less than 0.79 inches in height.

s climbing

climbing mode by pressing CLIMB before using.