Youngshin Electronics JMA510SS User Manual

CM3000

CM3000

INSTALLATION GUIDE

CM3000

YOUNG SHIN Electronics Co., Ltd.

www.MAGICAR.com

FCC ID : 044JMA510SS

This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions :
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference

that may cause undesired operation.

CAUTION :

Changes or modifications not expressly approved by the party
responsible for compliance could void the user

s authority to

operate this device.

INSTALLATION GUIDE

Compustar A Controllers

Page 2

TABLE OF CONTENTS

ᵄ

Wiring Diagram

ᵄ

Installation of FM or SS Antennas and RPS

ᵄ

Option Programming for Four Button Remote

ᵄ

Option Programming for Six Button(ONE WAY) Remotes

ᵄ

Remote - Pager Programming Menu Options

Page 4

Page 5

Page 6

Page 7

Page 7

ᴍᴍᴍᴍᴍᴍᴍᴍᴍᴍᴍᴍᴍᴍᴍᴍᴍᴍᴍᴍᴍᴍᴍᴍᴍᴍᴍᴍᴍᴍᴍ

ᴍᴍᴍᴍᴍᴍᴍᴍᴍᴍᴍᴍᴍᴍ

ᴍᴍᴍᴍᴍᴍᴍᴍᴍᴍᴍᴍᴍ

ᴍᴍᴍᴍᴍᴍ

ᴍᴍᴍᴍᴍᴍᴍᴍᴍᴍᴍᴍᴍ

Under normal circumstances, Reservation Mode is cancelled

when

a door or hatchback opens. Please verify if the opening of any door or
hatchback cancels Reservation Mode. If any of the doors or hatchback is not
monitored by CompuStar because of improper installation or a faulty dome light switch,
do not use the CompuStar and take your vehicle to the dealer immediately for repair.

Do not set Reservation Mode when the window(s) are open or if there is anyone
inside of the vehicle including animals.

This system requires no specific maintenance. Your remote-pager is powered by a single
AA battery that will last approximately one month under normal use depending on the
make and model of your vehicle. There is a battery icon in the lower right corner of the
CompuGLO LCD indicating remaining battery life. When the battery weakens, the
operating range will be reduced and the CompuGLO LCD will dim. Contact your
authorized CompuStar dealer if you have additional questions.

System Maintenance

Page 4

Important!

The model name, 2WSSR, stands for Two Way Spread Spectrum Remote with
Liquid Crystal Display. This 5-channel transmitter that allows you to activate multiple

functions by pressing a combination of 4 buttons on the unit in order to transmit signals.

REMOTE-PAGER : 2WSSR w/LCD

The remote-pager comes with CompuGLO which is a unique color LCD display that
visually tells the vehicle owner the security status of your car at all times. There are
differing icons that will appear on your CompuGLO LCD indicating what your vehicle is
currently doing.

CompuGLO color LCD

(Liquid Crystal Display)

The product s warranty is automatically void if its date code or serial number is defaced,
missing or altered. This warranty will not be valid unless you have completed the regis
tration card and mailed it to Firstech, Inc., within 10 days after the purchase to the
address listed on the registration card.

Your Warranty

Congratulations on the purchase of your high-tech vehicle security system and remote
auto-starter. This system has been designed to provide years of trouble-free operation.
Due to the complexity of the system, it must only be installed by an authorized
CompuStar dealer for full warranty and technical support. Installation of this product by
anyone other than an authorized dealer voids the warranty.

The owner s guide should help you to get the most out of your system. Please take
time to read it thoroughly prior to using this system. Additional replacement copies of this
manual are available for downloading at www.compustar.org.

Important Information

Please take these safety precautions under the following conditions:

1. Servicing the vehicle

When servicing (i.e. changing the oil, washing your car) your automobile, the CompuStar
system should be in Valet Mode. There is a safety shutdown switch under the hood that
deactivates the remote starter function if the hood is open. However, if the switch has
been damaged or the switch has been installed improperly, the vehicle may start when
Button II is pressed for 2 seconds even if the hood is open.

2. Loaning your vehicle to others

Whenever you loan your vehicle to an individual who is not familiar with Compustar,
please put the vehicle in Valet mode. This will prevent the vehicle loaner from accidental­ly activating the CompuStar auto-security system.

3. For manual transmission vehicles

If the Compustar 2WSSR is installed in a manual transmission vehicle, extra precautions
are required because the Compustar does not monitor the gear shift :

Safety Information

Page 3

Page 6

Page 5

Shock

Turbo
Timer

Passive

Indicates if the Shock Sensor is on or off. See page 12.

Indicate if Turbo Mode is on or off. See page 17.

Indicates if Timer Start Mode is on or off. See page 16.

Indicates if Passive Arming Mode is on or off. See page 17.

Icon Explanation

Indicates that the second stage shock sensor has been triggered.

If the icon appears continuously, you are in mute(vibration) mode. If the
icon blinks, the first stage shock sensor has been triggered. See page 15.

Indicates if you are in Valet Mode. See page 15.

Indicates if your car parking lights are flashing.

Indicates that your car siren is turned on or off when you lock or
unlock the vehicle.

Indicates that someone is paging you from your vehicle.

Displays if your car is locked or unlocked.

Indicates if your remote-pager is transmitting signals to the controller unit.

Displays remaining battery life.

Displays if your door is open.

Displays if your vehicle has auto-started properly or ignition on.

Displays if your trunk is open.

Remote-Pager Button Functions

1

2

3

4

5

6

7

8

9

10

11

12

13

I

II
III
IV
I

-

II

-

III

-

IV

-

( I+ II)
( I+ III)
( II+III)

(II+ IV)

(III+IV)

( I + III)

-

14

15

16

17

1/2 sec

1/2 sec

1/2 sec

1/2 sec

2 sec

2 sec

2 sec

2 sec

1/2 sec

1/2 sec

1/2 sec

1/2 sec

1/2 sec

2 sec

Alarm Mode - on/off, RPS - on/off

Auxiliary Option 1

Auxiliary Option 2

Query Function

Alarm Mode - on/off, RPS - on/off

Auto-start Function - on/off

Trunk Release - on/off

Panic Mode

Car Siren for Lock/ Unlock-on/off

Valet Mode - on/off

Passive Arming - on/off

Timer Start Mode - on/off

Turbo Mode - on/off

On

Off

Off

Off

Off

On

Off

Shock Sensor – on/off.

( II + III)

-

2 sec

Mute mode (Vibration only) – on/off.

( I + II)

-

2 sec

Programming Menu 1

( I + III)

-

2 sec Programming Menu 2

Button

Channel

Press for

Function

Factory
Setting

Note :

"

( )

" means simultaneously pressing the buttons

"

( )

-

" means simultaneously pressing the buttons for 2 seconds.

The user can activate differing functions of CompuStar 2WSSR system by pressing
one or two buttons simultaneously (ex.(

I+IV

) ) located on the antenna side of your

Compu Star remote-pager.

Page 8

(-)

Output for Parking Lights : Some vehicles, such

as Jeep, have negative Parking lights.

An Aux output is a 5sec pulse that can be changed to Latch.
See Programming Options.

Starter Kill supplies a negative 250mA output when the system is armed.

Dome Light Supervision : Dome light is turned on for one minute
after unlock. If you program Dome Lghts Rearm option, the
Violet wire of CN2 supplies a ground pulse before Lock.
The Dome Light Rearm Option is to simulate opening the door
and pressing the factory lock button for factory arming.

The sequence for the Rearm pulse : pulse when armed (locked).
The sequence for the Disarm pulse : a pulse when disarmed(unlocked).

Installation of FM or SS Antennas and RPS

Installation of FM or SS Antennas and RPS.
The antennas have been calibrated for
horizontal installation at the left-top corner
of the windshield. Different installation
may adversely affect the
transmitting distance.

RPS

Wiring Diagram

Page 7

(-)
(+)

Tx Antenna Date Cable

Rx Antenna Data Cable

LED (-)

(+)

RPS Sensor

(-)

(+) Siren Output
(+) Parking Light
12V Constant
Ground

(-) 250mA Parking Light
(-) 250mA Horn Output
(-) 250mA Aux1
(-) 250mA Aux2
(-) 250mA Starter Kill
(+) Ignition Sensing Input
(-) 250mA Dome Light Output
(-) 250mA Rearm Output
(-) 250mA Disarm Output

(-) Hood Pin Sensing
(-) Trunk Pin Sensing
(-) Door Pin Sensing
(+) Door Pin Sensing
(-) Optional Trigger 2ndStage
(-) Optional Trigger 1

st

Stage

(+)
(-) 250mA Trunk Output
(-) 250mA 2

nd

Pulse Unlock
(-)250mA Unlock Output
(-) 250mA Lock Output
(-)

(-) LED
(+) LED

(-)
2

nd

Stage Dual-Shock
(+)
1

st

Stage Dual-Shock

ḟ

ḟ

Page 10

Programming

Programming Menu 1

Programming Menu 2

Option Selection

Factory Setting

Option Selection

Default Setting Selection

6 Button Remote

(Trunk+Start)-

(Trunk+Stop)-

(Stop)-

Lock

Unlock

(Start)-

4 Button Remote

(I+II)-

(I+IV)-

(IV)

( I )

( II )

( III )

Option Programming for Six Button

(ONE WAY)

Remotes

.

The procedures will be same as the 4 button remotes except the use of the
different buttons.

Feature

Door Lock / Unlock Pulse Duration

Driver’s Priority Unlock

Double Pulse Unlock

Dome Light Factory Rearm

0.8 sec

OFF

OFF

OFF

2.5 sec

ON

ON

ON

Factory Default

Setting - Button I

Optional

Setting - Button II

Remote-Pager Programming Menu Options

Programming Menu #1 ( Door Lock Options )

1- 1

1- 2

1- 3

1- 4

1- 5

1- 6

1- 7

Note

1- 4 This feature unlocks the driverᴗs side door lock with the first unlock pulse.

A second unlock pulse is need to unlock the rest of the car doors.

Page 9

ᵉ

If you hear a long chirp, you are going out of programming mode,

please go back to Step 1.

ᵉ

If you want to change more options, go back to Step 1.

Option Programming for Four Button Remotes

Step1:

For programming menu 1 : Press Buttons (

I+II

) for 2 seconds.

For programming menu 2 : Press Buttons (

I+IV

) for 2 seconds.

The car will chirp once indicating that you are in programming mode.

Step2:

Within a 2 seconds after pressing (

I+II

) or (

I+IV

), press Button IVthe

number of times to go to the option number you want to change.

You will hear a chirp and see the parking lights flash each

time when you press Button

IV

.

Step3:

Wait a few seconds. You will hear a number of chirps and see a

number of parking light flashes corresponding to the option num
ber you want to change. If the number of chirps or flashes is not
what you want, go back to Step 1.

Step4:

Press Button I for the default factory settings and your car will

respond by one chirp and one flash. Press Button

II

for the
optional setting and your car will respond by two chirps and two
parking light flashes.

Resetting the Programming Options to the factory default settings.

Step1

:

Press Buttons (

I+II

) simultaneously or Buttons (

I+III

) simultaneously
for 2 seconds. Step 1 is confirmed by a car chirp and a one-time
flashing of the parking light.

Step2

:

Press Button

III

three times. This is confirmed by a car chirp and

parking light flash each time you press Button

III

. A few second later,
your car will chirp and parking light flash three times rapidly.
Your car is now set to all of the original factory default settings.

Page 12

Panic Mode

IV for 2 seconds

1.5 minutes
Starter-Kill

Activated immediately

N/A

Button

Siren

Installation required

Starter Kill

Ignition Kill

Anti-Jacking Mode

IV for 2 seconds

1.5 minutes
Ignition-Kill

N/A

Activated immediately if key is not on.

If key is on, activated in 30 seconds after

pressing the Button

IV

2- 5 With this option, the doors will lock after the ignition is turned on and unlock

when the ignition is turned off.

2- 6 & 2- 7

You can program the duration between 1 to 99 seconds.
You can program the “Latch Mode” also.

Setting

Contents

2-9

Off

Pluse

Latch

Pluse

Latch

On

2-6

2-7

off

on

off

on

1-99,

Latch

1-99,

Latch

2-9 If you need more than 2 Aux outputs, you can interface the CM 3000 with

Channel Expander for 7 Aux outputs. If you take this Channel Expander option
and you turn on the Passive setting of the 2WFMR, the four buttons of the
2WFMR operate these 7 outputs instead of normal button functions such as
arm/disarm or start/stop. Refer to the manual of the Channel Expander.

2-10

If you take the Channel Expander option of 2-9, the Passive setting of the

remote will change the button functions to operate of the Channel Expander.
The Passive setting of the remote will no longer work as the Passive Arming
function. Therefore, if you need both Channel Expander and Passive Arming
function, you need to choose this option.

In order for this feature to operate, the installer must use the

2ndUnlock Wire (Or/Bk wire of Connector 4). Isolate the driverᴗs door actuator
from the rest of the other doors. Call us for the technical support if you are not
sure about this.

Programming Menu #2 (Security Options)

Note

2-4 With this option, Panic mode becomes Anti-Jacking mode.

The differences between Panic mode and Anti-Jacking mode are :

Important!

Feature

Passive Locking, too

No Passve Locking

Remote

controller

OFF
OFF

0.5 Sec

0.5 Sec
30 Sec

ON

ON
Latch
Latch

60 Sec

Factory Default

Setting - Button I

Optional

Setting - Button

II

Programming

Method

2- 3

2- 4
2- 5
2- 6
2- 7
2- 8

Passive Arming

Anti-jacking

Ignition Controlled Door Lock

Aux 1 Output
Aux 2 Output

Siren Duration

Feature

Non using of Channel

Expander module

When Option 2-9 is on

Non using of Passive

Mode with remote

Using of Channel
Expander module

Using of Passive

Mode with remote

Channel Expander

Passive Arming with the

Channnel Expander

Option
Programmer
(CM3 -Series)

OFF ON

Programming

Method

2- 9

2 - 10

Page 11

Page 14Page 13

Adjusting the Car Siren Volume:

In order to decrease the chirping volume of the siren, cut the loop located on
the siren.

Adjusting the Shock Sensor Sensitivity:

In order to the shock sensor sensitivity, turn the screw located on the
sensor clockwise. In order to decrease the sensitivity, turn the screw located
on the sensor counter-clockwise. Turning the screw just a small amount can
make a big difference so make sure you recheck the sensitivity after each adjust­ment.

Setting

AUX No.

2-9

On

Access to passive mode through a remote

Non setting of passive mode

Setting of passive mode

Button

II

Button

III

All outputs are connecting with
Channel Expander through AUX1.

Button

I

Button

II

Button

II

Button

III

AUX 1,
AUX 2

Button

III

Button

IV

Button

II-

Button

III-

Button

IV-

off

AUX 1

AUX 2

AUX 3

AUX 4

AUX 5

AUX 6

AUX 7

Output