BEFORE CALLING FOR SERVICE
Be fo re c al li ng f or s er vi ce , pl ea se c he ck t he t ro ub le s ho ot in g ch ar t be lo w.
It i nc lu de s se ve ra l co mm on f au lt s wh ic h yo u ca n co rr ec t, m ak in g a se rv ic e ca ll
un ne ce ss ar y.
OWNER’S MANUAL
Please read this owner’s manual thoroughly before operating
and keep it handy for reference at all times.
Point- Of-Use
Water Cooler
Model No. : YP-G10 (Hot & Cold Water)
YP-G1T (Hot & Cold Water)
YOUNG ONE Corporation
7.12.Z1 The specific instructions related to the safe operation of this
appliance (as given in 7.12 of this standard) shall be collated together
in the front section of the user instructions. The height of the characters,
measured on the capital letters, shall be at least 3 mm.
These instructions shall also be available in an alternative format, e.g. on
a website.
Check if the machine is placed close to a heat source
or direct sunlight.
Check if the machine is placed too close to a wall.
Machine must be more than 4 inches from the wall.
Check turn hot water switch on at the rear side.
Check if plugged in.
Check voltage. (It may be too high or low)
Cooler does not
operate.
Cooling efficiency
is low.
Heating efficiency
is low.
Is the machine placed on uneven floor?
Put the machine on firm and even surface.
ls there an obstacle at the back of the machine?
Remove the obstacle.
Abnormal noise
Drinking water does
not flow well.
Check if the water valve is on “open” position.
CIRCUMSTANCE
POSSIBLE CAUSE AND REMEDY
SAFETY INSTRUCTIONS
INSTALLATION
2
7
Use the machine for its intended
purpose only as described in this
manual.
Do not put any objects on the machine.
Unplug the machine before cleaning or
replacing parts of it.
Do not locate the machine direct
sunlight.
Do not locate the machine near the
radiator.
Do not locate the machine within or
directly adjacent to toilet facilities.
Do not locate the machine in constantly
damp areas,beneath dripping pipes,
or where water may collect underfoot.
Do not install the machine in a humid or
wet area.
All servicing should be performed by
qualified personnel only.
Do not use multiple socket outlet to
supply power.
If the power cord is damaged, it must
be replaced by the manufacturer or
by its service agent or a similar
qualified person in order to avoid injury
or hazard.
Place the machine on firm and even
surface. Unbalanced installation may
cause noise or vibrations.
Put the machine in an open area and
at a distance of more than 4 inches from
the wall. Otherwise, the cooling efficiency
may decrease.
The machine should be installed
within 6 feet from the nearest power
outlet.
The machine must be attached to a
portable water source.
The tubing job(usually 1/4”) which
connects the machine to the water supply
should not be exceed in 20 meters (65 feet).
Use only grounded outlet wall sockets.
The
machine
should be positioned in
such a way that the plug is easily
accessible.
CAUTION
1. Do not tilt appliance more than
45 degrees when moving system.
2. To avoid a hazard due to instability
of the appliance, it must be fixed in
accordance with the instructions.
Have 100mm sp ace bet ween the wall a nd the a pplianc e
and i nstall a bove th e floow where
it is solid a nd flat .
(After transporting, don’t switch on the
power supply for approximately 1 hour)
1. This appliance is not intended for use by persons (including children)
with reduced physical, sensory or mental capabilities, or lack of
experience and knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a person responsible
for their safety.
Children should be supervised to ensure that they do not play with
the appliance.
2. This appliance can be used by children aged from 8 years and above
and persons with reduced physical, sensory or mental capabilities or
lack of experience and knowledge if they have been given supervision
or instruction concerning use of the appliance in a safe way and
understand the hazards involved. Children shall not play with the
appliance. Cleaning and user maintenance shall not be made by
children without supervision.
3. For appliances with type Y attachment, the instructions shall contain
the substance of the following.
If the supply cord is damaged, if must be replaced by the manufacturer,
its service agent or similarly qualified persons in order to avoid a hazard.
4. WARNING : To avoid a hazard due to instability of the appliance, it
must be fixed in accordance with the instructions.
3
PARTS IDENTIFICATION
INSTALLATION
6
HOW TO USE THE HOT WATER
Push the faucet lever for the hot water and press the lock button.
HOW TO USE THE COLD WATER
Push the faucet lever for cold water and push the continuous supply lever to the right.
Cold water lever
Push this lever.
For child lock
button
Lamp for hot
Lamp for cold
Rear Panel
Hot water Switch
Compressor base
1. Connect water tube (”A” side) to water inlet.
(water tube linked to the water valve) (POU Only)
2. Connect water tube (”B” side) to city water line.
Open the water valve after connecting the water tube
(”B” side) to the city water line. (POU Only)
3. Plug in.
4. Check hot water, cold water respectively.
Caution ! Turn the hot water switch on after checking
the hot water flow.
Notes :
1. If the water line pressure exceeds 65PSI,
a pressure regulator must be used.
2. Refer to user’s manual supplied with each
machine
for operation and care.
Hot
(or Room Temperature)
Water lever
Push this lever.
Tray drip
To gather the
overowing water.
Switch (Rear side)
To turn on (”I” position)
for hot water or
turn o(“O” position)
for room temp. water.
Temp. controller (Rear side
)
To control the temperature
of cooling water.
SPECIFICATIONS
YP-G10 YP-G1T
(220-240)V~ / 50Hz
0.5A
420W
Total
R-134a (32g)
330 W
287x357x970 270x452x515
1.85 ℓ2.3 ℓ
Water Valve
Water Tube
“A” Side
“B” Side
Filter out
Filter in
Water inlet
Water inlet
4 5
SAFETY INSTRUCTIONS
CARE AND MAINTENANCE
SAFETY NOTICE
CLEANING
EXTERIOR
INTERIOR
LONG-TERM CARE
WATER LEVER
OPERATION PROCEDURE
CLEAN
The water faucet becomes easily dirty by
constant use. Clean it thoroughly at least
once in 3 months (figure 5).
Unplug the cooler before cleaning.
Clean the cooler regularly to ensure its
maximum efficiency.
Clean the water tank with vinegar if you
do not use the cooler for several days.
Clean the cooler every two months,
unless it includes in-tank sanitization
system. Do not use abrasive cleaning
tools nor sharp tools which may cause
defects or damages on the system.
(figure 4)
For extended vacation or absence, turn off
the power and clean the cooler inside and
out thoroughly.
Do not clean any part of the cooler with
gasoline, kerosene, thinner, etc.
Use clean cloth and mild detergent
when cleaning. Dry the surface with
clean and soft cloth. (figure 3)
Connect the water tube to water
inlet at the rear side and then
open the water valve on position.
1. WATER SUPPLY
2. Plug in.
3.
Check flow of hot water, turn hot
water switch on at the rear side.
4. Check flow of cold water, hot water.
Note:
1. If hot water is connected to machine
as water source, it may damage the
machine. (figure 1)
1. Keep unplugged when the machine is
not in use for long period. (figure 2)
2. Do NOT put hands in the water tank
while in use.
3. Wait at least 4 minutes before restarting
the machine after unplugged.
STOP
Note:
1. Be careful, when hot water is flowing.
Otherwise you may injure yourself.
HOT WATER
Loading...